Fluke TS 19 Bedienungsanleitung

TS®19

Portable Test Telephone

PN 2448484

October 2005 Rev. 1 2/09

All product names are trademarks of their respective companies.

Users Guide

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Each Fluke Networks product is warranted to be free from defects in material and workmanship under

normal use and service. The warranty period for the mainframe is 18 months and begins on the date of

purchase. Parts, accessories, product repairs and services are warranted for 90 days, unless otherwise stated.

Ni-Cad, Ni-MH and Li-Ion batteries, cables or other peripherals are all considered parts or accessories. The

warranty extends only to the original buyer or end user customer of a Fluke Networks authorized reseller,

and does not apply to any product which, in Fluke Networks’ opinion, has been misused, abused, altered,

neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling. Fluke

Networks warrants that software will operate substantially in accordance with its functional specifications

for 90 days and that it has been properly recorded on non-defective media. Fluke Networks does not warrant

that software will be error free or operate without interruption.

Fluke Networks authorized resellers shall extend this warranty on new and unused products to end-user

customers only but have no authority to extend a greater or different warranty on behalf of Fluke Networks.

Warranty support is available only if product is purchased through a Fluke Networks authorized sales outlet

or Buyer has paid the applicable international price. Fluke Networks reserves the right to invoice Buyer for

importation costs of repair/replacement parts when product purchased in one country is submitted for repair

in another country.

Fluke Networks warranty obligation is limited, at Fluke Networks option, to refund of the purchase price,

free of charge repair, or replacement of a defective product which is returned to a Fluke Networks

authorized service center within the warranty period.

To obtain warranty service, contact your nearest Fluke Networks authorized service center to obtain return

authorization information, then send the product to that service center, with a description of the difficulty,

postage and insurance prepaid (FOB destination). Fluke Networks assumes no risk for damage in transit.

Following warranty repair, the product will be returned to Buyer, transportation prepaid (FOB destination).

If Fluke Networks determines that failure was caused by neglect, misuse, contamination, alteration, accident

or abnormal condition of operation or handling, or normal wear and tear of mechanical components, Fluke

Networks will provide an estimate of repair costs and obtain authorization before commencing the work.

Following repair, the product will be returned to the Buyer transportation prepaid and the Buyer will be

billed for the repair and return transportation charges (FOB Shipping point).

THIS WARRANTY IS BUYER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. FLUKE NETWORKS SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, ARISING FROM ANY

CAUSE OR THEORY.

Since some countries or states do not allow limitation of the term of an implied warranty, or exclusion or

limitation of incidental or consequential damages, the limitations and exclusions of this warranty may not

apply to every buyer. If any provision of this Warranty is held invalid or unenforceable by a court or other

decision-maker of competent jurisdiction, such holding will not affect the validity or enforceability of any

other provision.

4/04-18

Fluke Networks

PO Box 777

Everett, WA 98206-0777

USA

TS®19 Portable Test Telephone

Contents

Title Page

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Contacting Fluke Networks . . . . . . . . . . . . . . . . . 1

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . 1

Physical Characteristics. . . . . . . . . . . . . . . . . . . . . 2

Handgrip Controls. . . . . . . . . . . . . . . . . . . . . . . . . 2

Keypad Controls and Indicators. . . . . . . . . . . . . . 3

Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction

The TS19 Portable Test Telephone, often called a “butt-

in,” is a self-contained, line-powered, portable handset

used by installers, repair technicians, and other

authorized personnel for line testing and temporary

communications.

The TS19 Portable Test Telephone provides both DTMF

(Touch Tone) and dial pulse output. The TS19 also

provides last number redial, dual monitor impedance,

an electronic ringer (on/off), and field replaceable line

cords and belt clips.

Registration

Registering your product with Fluke Networks gives

you access to valuable information on product updates,

troubleshooting tips, and other support services. To

Fluke Networks website at www.flukenetworks.com/

registration.

Contacting Fluke Networks

www.flukenetworks.com

[email protected]

+1-425-446-4519 or 1-800-283-5853

•

Australia: 61 (2) 8850-3333 or 61 3 9329 0244

•

Beijing: 86 (10) 6512-3435

•

Brazil: 11 3759 7600

•

Canada: 1-800-363-5853

•

Europe: +44-(0) 1923 281 300

•

Hong Kong: 852 2721-3228

•

Japan: 03-3434-0510

•

Korea: 82 2 539-6311

•

Singapore: +65-6799-5566

•

Taiwan: (886) 2-227-83199

Visit our website for a complete list of phone numbers.

Safety Information

The following IEC symbols are used either on the test

set or in the manual:

Warning: Risk of personal injury. See the

manual for details.

Caution: Risk of damage or destruction to

equipment or software. See the manual for

details.

XWarning: Risk of electric shock.

.Earth ground

PConformité Européenne. onforms to relevant

European Union directives.

)CAN/CSA-C22.2 No. 60950-1-03

CAN/CSA-C22.2 No. 1010.1-92 + CSA-C22.2 No.

1010.1B-97, UL/ANSI 3111-1

~Do not put products containing circuit boards

into the garbage. Dispose of circuits boards in

accordance with local regulations.

TS19 Portable Test Telephone

Users Guide

WXWarning

Good safety practices prohibit the

connection of the TS19 and similar test sets

to 117 volts AC commercial electrical power;

should the TS19 be connected to commercial

power, all warranties are voided.

The TS19 Portable Test Telephone is not

designed to meet the outside plant

requirements of Bellcore Publication TR-TSY-

000344. It is recommended that this product

not be used outside during adverse and/or

wet weather conditions.

Do not use the test set if it is damaged.

Before you use the test set, inspect the case.

Look for cracks or missing plastic. Pay

particular attention to the insulation

surrounding the connectors.

If this product is used in a manner not

specified by the manufacturer, the

protection provided by the product may be

impaired.

Physical Characteristics

See Figure 1.

bdn01.eps

Figure 1. Physical Characteristics

The case is designed to give rugged service and

withstand the rough handling and shocks

normally associated with craft tools.

The back of the handgrip is contoured and has a

non-slip surface, freeing both hands while the

Portable Test Telephone rests on the shoulder.

The keypad has 12 keys on a black plastic bezel

that is recessed into the receiver end of the

housing. The recessed bezel protects the keypad

and prevents accidental key presses.

The spring-loaded belt clip ensures a secure

connection to a belt loop or D-ring. The belt clip

may be replaced in the field (see Belt Clip

Replacement).

The Portable Test Telephone is equipped with one

of two cord configurations. The line cords may be

replaced in the field.

Handgrip Controls

See Figure 2.

bdn02.eps

Figure 2. Handgrip Controls

Last Number Redial Button: The LNR button serves

as a last number dialed key. The number may be

redialed in either pulse or tone mode as selected

by the PULSE/TONE switch. The last number dialed

may be up to 18 digits long.

Note

The redial memory has a 15-minute time limit

after the TS19 has been disconnected from a

working telephone line. After 15 minutes, the

number will be lost from memory.

Keypad Controls and Indicators

HI Z/RING/TALK Switch: This three-position slide

switch is labeled as HI Z for high impedance

monitoring, RING for ringer and low impedance

monitoring, and TALK for talk.

•

In the

HI Z

position, the TS19 is on hook with a

high impedance coupling to the telephone line.

This allows for telephone line monitoring without

disrupting conversations, data or signaling.

•

In the

RING

position, the TS19 is on hook with an

electronic ringer connected to the telephone line.

The TS19 is low impedance coupled to the line for

monitoring of optional line identification tones.

Also, the TS19 provides enhanced receive levels.

•

In the

TALK

position, the TS19 is off hook and may

be used for dialing and talking. In this mode, the

TS19 performs as an ordinary telephone.

PULSE/TONE switch: This two-position slide switch

labeled PULSE/TONE, is located on the inside of

the handgrip just below the receiver. The switch

selects the signaling output. TONE for DTMF of

PULSE for dial pulse.

Keypad Controls and Indicators

See Figure 3.

Keys: The 12 standard keys will send either DTMF tones

or dial pulses, depending on the PULSE/TONE switch

setting.

Polarity LED: This red LED is located just below the

keypad. The LED indicates polarity (see “Polarity

Check”). The red LED lights if the red test lead is

connected to the Tip (positive) side and the black test

lead is connected to the Ring (negative) side.

bnd03.eps

Figure 3. Keypad

Cords

See Figure 4.

The TS19 comes with either a standard cord or an

angled bed-of nails cord (see

and

below). The line

cord can be replaced in the field (see “Line Cord

Replacement”).

bdn04.eps

Figure 4. Line Cords

Various cord types may be ordered for field

replacement:

Piercing Pin Cord: This cord is equipped with a

modular plug on one end, and has two five and

one half foot long fabric covered leads, one red

and one black. Each conductor is fitted with an

alligator clip offset 20 degrees to minimize clip

shorting. The clips have insulation piercing spikes

and a neoprene boot. Cord Number: P1980001.

Banana Jack Cord (STD): This is the standard cord.

This cord is equipped with a modular plug at one

end and two banana jacks at the other with

alligator clip adapters. Cord Number: P1980003.

TS19 Portable Test Telephone

Users Guide

Ground Start Cord: This cord consists of two

conductors with alligator clips. In addition, the red

(ring) conductor has a banana jack attached. This

jack is located six inches below the Portable Test

Telephone and is partially covered by the outer

fabric of the cord. A separate cord is also included.

This cord is 36 inches long with a banana plug on

one end and an alligator clip on the other. Cord

Number: P1980007.

Angled Bed-of-Nails Cord (ABN): This cord is

similar to the standard cord (STD), except that

each alligator clip is equipped with a “bed-of-

nails” and an insulation piercing spike. Cord

Number: P1980009.

Operation

WXWarning

When connecting to metallic network wires,

always handle alligator clips by the

insulated boots.

Monitoring: Move the HI Z/RING/TALK switch to HI Z

and connect the line leads to the telephone line under

test. Monitoring may now be done without disrupting

traffic.

Polarity Check: Move the HI Z/RING/TALK switch to

TALK. Connect the line leads to the telephone line

under test. The red LED lights if the red test lead is

connected to the Tip (positive) side and the black test

lead is connected to the Ring (negative) side.

Dialing:

Move the PULSE/TONE Switch to PULSE or TONE,

depending on the type of dial signaling required.

Move the HI Z/RING/TALK switch to HI Z. Connect

the line cord clips to the telephone line. Listen to

verify that the telephone line is idle.

Move the HI Z/RING/TALK switch to TALK and

verify that dial tone is received (when finished).

Enter the desired number to be called on the

keypad. If tone signaling is selected, the tones for

each digit are generated as each key is pressed. If

rotary dial pulse signaling is selected, the desired

number may be entered at any rate on the

keypad; digits will automatically be pulsed out at

the correct rate. To end the call, move the HI Z/

RING/TALK switch to the HI Z position.

Last Number Redial: The last number dialed can be

automatically redialed with the PULSE/TONE switch set

to PULSE or TONE. Use the following procedure for a

number up to 18 digits long:

Go on hook (move the HI Z/RING/TALK switch to

the HI Z position) for at least ½ second.

Move the HI Z/RING/TALK switch back to the TALK

position.

Press the LNR button and the number will be

automatically redialed.

Note

The redial memory has a 15 minute time limit

after the Portable Test Telephone has been

disconnected from a working telephone line.

After 15 minutes, the number will be lost from

memory.

Electronic Ringer (On/OFF): Move the HI Z/RING/TALK

switch to RING and connect line leads to the telephone

line. The piezo-electric transducer electronic ringer will

“ring” whenever it detects ringing voltage on the line.

Answer the call by moving the HI Z/RING/TALK switch

to TALK. To disable the ringer, move the HI Z/RING/

TALK switch to HI Z.

Troubleshooting

The following troubleshooting procedures are based

largely on the audible click heard in the receiver of the

TS19 when the two Portable Test Telephone leads are

placed on battery potential and ground respectively, or

across the terminal of an electrically charged capacitor.

These clicks and other sounds can help you locate open

circuits, shorts, crosses, and grounds.

Maintenance

To locate a short circuit: Open one side of the

telephone line and place the test set in the loop — one

lead to each side of the opened line. On the CO side of

the fault, a loud click will be heard. On the field side of

the fault, no click will be heard.

To locate an open circuit: Bridge the test set across the

circuit line — one test lead on tip, the other on ring.

Moving away from the CO, the fault is at the point

where the loud click disappears.

To verify continuity: Place one of the line leads on a

local ground and the other on the conductor in

question. On a good Ring conductor, a click will be

heard. On a good Tip conductor, an inductive hum will

be heard (due to the difference in ground potential

between the CO ground and the local ground).

WWarning

When testing circuits close to the battery

source, the clicks may be loud enough to

hurt your ear if the receiver is held too

tightly against the ear. The TS19 is designed

to rest comfortably on the shoulder with the

receiver away from the ear. It should be

used in this position when listening for

clicks.

Maintenance

WXWarning

Disconnect clips from any metallic

connections before performing any

maintenance. Read all instructions

completely and understand possible hazards

to end user if not performed by authorized

service personnel.

WCaution

Do not use CRC Cable Clean®or any similar

chlorinated solvent on the TS19. Doing so

will damage the TS19 Test Telephone.

Belt Clip Replacement

The ordering number for the replacement belt clip is

P3218249. To replace the belt clip assembly:

Place the TS19 on a firm and level working surface

with the keypad up.

Remove the two screws which secure the belt clip

to the TS19’s plastic grip (one screw also secures

the strain relief cord). Remove and discard the old

belt clip.

Position the new belt clip so that its screw

mounting holes line up with the mounting holes

in the TS19. Insert the screws and tighten. Make

sure the strain relief for the cord is properly

reinstalled.

Line Cord Replacement

To replace the line cord:

WXWarning

Disconnect from telephone network when

replacing line cord.

Place the TS19 on a firm and level working surface

with the keypad up.

Remove the screw and the strain relief cord.

Depress the plastic tang on the modular plug of

the line cord where it enters the TS19’s modular

jack and gently pull the plug and cord free from

the jack. Discard the cord.

Insert the modular plug of the replacement cord

into the TS19’s modular jack and listen for a click.

The click indicates that the plug has “locked” into

position with its tang properly engaged to prevent

accidental removal.

Reinstall the screw for the strain relief cord.

TS19 Portable Test Telephone

Users Guide

Specifications

Electrical

Loop Limit 2.4 kΩmaximum at 48 VDC (nominal 15 mA minimum loop

current)

DC Resistance (Talk Mode) 150 Ωtypical at 80 mA current

AC Impedance (Monitor Mode) Low impedance (Ring position) 600 Ωat 1 KHz typical

High impedance (HI Z position) 100 kΩminimum at 1 KHz

Rotary Dial Output

Pulsing Rate

Percent Break

Interdigit Interval

Leakage During Break

10 pps +0.5 pps

60 % ± 2 %

800 ms typical

> 50 kΩ

DTMF Output

Tone Frequency Error

Level per Tone Pair

±1 % maximum

+2 dBm maximum, -8 dBm minimum

High versus Low Tone Difference 4 dB maximum

Physical

Length 8.75 in (22.2 cm)

Width 2.375 in (6.03 cm)

Height 3.375 in (8.57 cm)

Weight 10.8 oz (.307 kg) maximum

Environmental

Temperature Operating: -5 °C to +40 °C

Storage: -40 °C to +66 °C

Drop 1 m, 4 times

Altitude To 3,000 m (10,000 ft) maximum

Relative Humidity 10 %to 80 % (non-condensing)

Regulatory Standards Used

47 CFR Part 15, Subpart B

ICES-003 Issue 3

AS/NZS 3548

EMC Directive 89/336/EEC, EN 55022:98, EN 61326:97, A1:98 Annex C, EN 61000-4-2, EN 61000-4-3

LV Directive 73/23/EEC, EN 610010.1 (1993)

Certifications and Compliance

Conformité Européenne. Conforms to relevant European Union directives.

CAN/CSA-C22.2 No. 60950-1-03

CAN/CSA-C22.2 No. 1010.1-92 + CSA-C22.2 No. 1010.1B-97, UL/ANSI 3111-1

Specifications subject to change without notice.

Andere Handbücher für TS 19

Inhaltsverzeichnis

Andere Fluke Telefon Handbücher

Fluke

Fluke TS 19 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung