Fluke 700PTP Bedienungsanleitung

PN 688736

December 1997, Rev.1, 8/02

All product names are trademarks of their respective companies.

Caution

To maintain proper operation of the fine

adjustment knob, never unscrew the fine

adjustment knob past the red line. If you do go

past the red line, vent the pressure from the

system before you re-engage the piston.

Red line indicator

pp03f.eps

8. Tighten the pressure release valve (item .).

9. If you want to limit the maximum pressure that can be

developed by the pump, tighten the maximum-stroke

limiting adjustment nuts (item -). This also reduces

the amount of pressure increase per stroke.

10. To apply very low pressures, use the fine adjustment

knob only (item /).

11. Squeeze the handles together to apply incrementally

higher pressure. For pressure over 7 bar (100 psi),

use two hands.

12. Adjust the pressure using the fine adjustment knob

(item /).

Replacement Parts

Hose assembly, Fluke PN 2029186

Seal kit, Fluke PN 2029173

Handle and main piston assembly, Fluke PN 2029199

Limited Warranty & Limitation of Liability

This Fluke product will be free from defects in material and

workmanship for one year from the date of purchase. This

warranty does not cover fuses, disposable batteries or damage

from accident, neglect, misuse or abnormal conditions of operation

or handling. Resellers are not authorized to extend any other

warranty on Fluke’s behalf. To obtain service during the warranty

period, send your defective calibrator to the nearest Fluke

Authorized Service Center with a description of the problem.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries do not

allow the exclusion or limitation of an implied warranty or of

incidental or consequential damages, this limitation of liability may

not apply to you.

Fluke Corporation Fluke Europe B.V.

P.O. Box 9090 P.O. Box 1186

Everett, WA 98206-9090 5602 B.D. Eindhoven

U.S.A. The Netherlands

Introduction

The Fluke 700PTP Pneumatic Test Pump (hereafter called

the pump) is a handheld device that develops precise

pressure and vacuum. The pump has the following

specifications:

•Pressure to 40 bar (600 psi)

•Vacuum to -0.96 bar (-13.9 psi)

•Wetted materials: anodized aluminum, brass, nitrile,

and nylon.

•Weight: 1.43 lb (650 g)

•Dimensions: length 8.66 in (220 mm), width 4.13 in

(105 mm), depth 2.48 in (63 mm)

Box Contents

•Model 700PTP Pneumatic Test Pump with hose and

1/4-in. NPT female adapter

•3/8-in. BSP male to 1/4-in. NPT female adapter

installed in the master instrument port

•Replacement seal kit for the pump

•Instruction Sheet

How to Contact Fluke

To contact Fluke, call one of the following numbers:

USA: 1-888-99-FLUKE (1-888-993-5853)

Canada: 1-800-36-FLUKE (1-800-363-5853)

Europe: +31 402-675-200

Japan: +81-3-3434-0181

Singapore: +65-738-5655

Anywhere in the world: +1-425-446-5500

Visit us on the World Wide Web at:

www.fluke.com

Fluke-700PTP

Pneumatic Test Pump

Instruction Sheet

Features of the Test Pump

pp01f.eps

No. Item Function

)Master

instrument

port

Port for Fluke 700 Series Pressure

Module. Supplied with 3/8-in. BSP

to 1/4-in. NPT adapter installed.

*Pressure /

vacuum

button

Push in from this side for vacuum,

and from the other side for

pressure. Use a small screwdriver.

+Test

pressure

port hose

Flexible hose to pressure

instrument under test.

,Test

pressure

port

1/4-in. NPT adapter

-Maximum

stroke

limiter

To limit the pressure from the hand

pump, tighten these nuts to shorten

the compression stroke.

.Pressure

release

valve

Unscrew to vent pressure from the

pump. Tighten the valve to close

the valve before you apply

pressure.

/Fine

adjustment

knob

Allows you to precisely adjust the

applied pressure.

Using the Test Pump

mA mA VV

RTD RTD

SOURCE

300V

MAX

30V

MAX

30V

MAX

30V

MAX

MEAS

CAT

743

DOCUMENTING PROCESS CALIBRATOR

MEAS

SOURCE

SETUP

RTD

789

456

123

SIGNAL

TEST

+–

Red

Black

ENTER

CLEAR

(ZERO)

RANGE

Pressure

Module

pp02c.eps

Warning

To avoid a violent release of pressure, always

depressurize the system slowly using the pressure

release valve (item .

., left) before you detach any

pressure line from the pump. Do not connect the

pump to an external pressure source.

1. Attach a 700 Series Pressure Module (hereafter called

“pressure module”) to the master instrument port.

2. Connect the pressure module to the calibrator as

shown in the figure.

3. Connect the test pressure port hose (item +) to the

pressure input of the pressure instrument under test.

4. Make sure the pressure/vacuum button (item *) is in

the desired postion.

5. Unscrew the pressure release valve (item .) to vent

pressure from the pump.

6. Zero the pressure module. The zeroing procedure

depends on which pressure module and calibrator you

are using.

7. Turn the fine adjustment knob (item /) to mid-range.

Inhaltsverzeichnis

Andere Fluke Prüfgeräte Handbücher

Fluke

Fluke ScopeMeter 199C Bedienungsanleitung

Fluke

Fluke MicroScanner Series Bedienungsanleitung

Fluke

Fluke FEV100 Bedienungsanleitung

Fluke

Fluke 1AC II VoltAlert Bedienungsanleitung

Fluke

Fluke 5520A Service Handbuch

Fluke

Fluke 753 Gebrauchs- und Pflegehandbuch

Fluke

Fluke P5515-V Bedienungsanleitung

Fluke

Fluke 975 AirMeter Montage- und Bedienungsanleitung

Fluke

Fluke PRV240FS Bedienungsanleitung

Fluke

Fluke 9640A Series Bedienungsanleitung

Fluke

Fluke 80PK-27 Bedienungsanleitung

Fluke

Fluke 725Ex Bedienungsanleitung

Fluke

Fluke CableIQ Bedienungsanleitung

Fluke

Fluke AIRCHECK Bedienungsanleitung

Fluke

Fluke 1507 Bedienungsanleitung

Fluke

Fluke 1625 Bedienungsanleitung

Fluke

Fluke 718 30G Bedienungsanleitung

Fluke

Fluke 729 FC Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungsanleitung

Fluke

Fluke 9102S Bedienungsanleitung

Fluke

Fluke 726 Bedienungsanleitung

Fluke

Fluke 716 Bedienungsanleitung

Fluke

Fluke T+ Gebrauchs- und Pflegehandbuch

Fluke

Fluke 714B/EN Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung