Fluke ScopeMeter 192B Handbuch

Fluke 192B, Fluke 196B, Fluke 199B, Fluke 192C, Fluke 196C, Fluke 199C, Fluke 215C, Fluke 225C SOMV 1 of 2 4/8/2011

Instrument Security Procedures

Model:

Fluke 192B, Fluke 196B, Fluke 199B, Fluke 192C, Fluke 196C, Fluke 199C,

Fluke 215C, Fluke 225C

Product Name:

190B and 190C Series ScopeMeter

Instrument Description:

High-performance Oscilloscopes

Memory Description:

The 190B/C series ScopeMeter Test Tools have the following memory devices:

1. D3500 Controller “Spider”. This contains a mask ROM 4kx32 with a initial

program with the operating code for the product and a RAM 1kx32 to

temporarily store stack values for computing actions.

2. D3502 SRAM 512k x 8 or 256k x 16 - SRAM memory to store:

•the actual screen and instrument setup

•saved screens and instrument setups

3. D3503 SRAM 512k x 8 - SRAM memory to store:

•the actual screen and instrument setup

•saved screens and instrument setups

4. A201 module with the following memory devices:

•D101, D202 : 1M x 16 Flash EEPROM or D101, D202 : 512k x

16 Flash EEPROM.

Non-volatile memory used to store operating code (instrument

firmware) for the product, and to store calibration constants.

•D201, D202 : 256k x 16 SRAM - SRAM memory to store:

- the actual screen and instrument setup

- saved screens and instrument setups

Fluke 192B, Fluke 196B, Fluke 199B, Fluke 192C, Fluke 196C, Fluke 199C, Fluke 215C, Fluke 225C SOMV 2 of 2 4/8/2011

Security Summary:

The operating code (instrument firmware) stored in D101-D102 on the A201

module can be read using special remote interface commands. The instrument

firmware can be loaded using a dedicated Fluke software program.

Calibration constants stored in D101-D102 on the A201 module can be read

using special remote interface commands. The calibration constants are

generated when the meter is sent through its calibration process and are

fundamental to the test tool operation.

Memory Cleaning Instructions:

The procedure to clear all saved screens and instrument set-ups differs per the

firmware version held in the ScopeMeter Test Tool. The version can be read by

pressing ‘USER’, then ‘F3 = VERSION & CAL’.

Firmware releases up to and

including V6.xx Firmware release V7.00 and beyond

1. Press the SAVE_PRINT button

2. Push the softkey F1 = SAVE

3. Push the softkey F3 = DELETE ALL

4. Press the softkey F4 = YES

1. Press the USER key

2. Press F1 = OPTIONS

3. Move the cursor to the field ‘Factory

Default’

4. Press F4 = ENTER to confirm this

selection

5. Press F4 = YES

The effectiveness of either of these procedures can be verified by checking the

status of the memories:

1. Press the SAVE_PRINT button

2. Press F1 = SAVE

The memory contents will show as ‘0 memory locations used’ or with all memory

number fields unfilled, confirming that all memories have been erased as

intended.

For all instrument versions mentioned and independent of the firmware release

that is installed, the test tool will also lose all data stored in SRAM in case the

instrument is not powered through its Power Adapter/Battery Charger and the

battery is removed for 10 minutes or longer.

Andere Handbücher für ScopeMeter 192B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fluke Prüfgeräte Handbücher

Fluke

Fluke NX1 Pocket Toner Bedienungsanleitung

Fluke

Fluke 2700G Gebrauchs- und Pflegehandbuch

Fluke

Fluke CNX a3000 Bedienungsanleitung

Fluke

Fluke 712 Bedienungsanleitung

Fluke

Fluke PM3082 Bedienungsanleitung

Fluke

Fluke 1587 FC Bedienungsanleitung

Fluke

Fluke 9011 Bedienungsanleitung

Fluke

Fluke ScopeMeter 190-502 Gebrauchsanweisung

Fluke

Fluke 154 HART Bedienungsanleitung

Fluke

Fluke CableIQ Bedienungsanleitung

Fluke

Fluke TS22A Bedienungsanleitung

Fluke

Fluke NX8 Bedienungsanleitung

Fluke

Fluke 705 Bedienungsanleitung

Fluke

Fluke 6003A Bedienungsanleitung

Fluke

Fluke 700PA3 Bedienungsanleitung

Fluke

Fluke 742A-10k Bedienungsanleitung

Fluke

Fluke 820-2 Bedienungsanleitung

Fluke

Fluke 5790A Bedienungsanleitung

Fluke

Fluke FiberInspector Versiv Series Gebrauchs- und Pflegehandbuch

Fluke

Fluke 1550C Bedienungsanleitung

Fluke

Fluke FLUKE-718 Bedienungsanleitung

Fluke

Fluke 80PK-10 Bedienungsanleitung

Fluke

Fluke CertiFiber Pro Bedienungsanleitung

Fluke

Fluke 707 Gebrauchs- und Pflegehandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung