Fluke TS54 Bedienungsanleitung

Toner and SmartTone Function

The toner helps you identify wire pairs and find

cables in bundles, at patch panels, or behind

walls.

Connect the test leads to two wires in a cable.

Press M, then select SmartTone. Use a tone

probe to find the place where the tone is the

loudest.

If there is voltage on the line, the display shows

SmartTone Volt Detect Lock Out, and toner will

not operate.

The SmartTone function helps you make sure

you correctly identify a wire pair. When you put

a short on the correct pair, the tone changes.

Standard VOPs

Press M, select TDR, then select VOP Setting.

VOP Twisted Pair Cable Types

68 Gel Filled19 AWG

64 Gel Filled 22 AWG

62 Gel Filled 24 AWG

60 Gel Filled 26 AWG

68 Paper 22 AWG

66 Paper 24 AWG

65 Paper 26 AWG

72 PIC 19 AWG

67 PIC 22 AWG

66 PIC 24 AWG (default)

64 PIC 26 AWG PN 3836378

August 2011, Rev. 3 2/2017

Data Test / Lockout Override

Connect the test set to Tip and Ring. Press P.

If data is present, a warning beep sounds, and

the test set does not go off-hook, and the

display shows Data Detect Lockout. To go off-

hook, press $.

Polarity

+: The polarity of Tip and Ring is reversed.

Redial the Last Number Dialed

Press P. Press L.

Speed Dial a Stored Number

Press P. Press R. Press the key ( 1through 9 )

of the memory location where the number is

stored.

Volume

Press CDto adjust the volume of the

speaker that is on.

Press M. To scroll, press CD. To select an

item or save a setting, press Magain. To exit,

select Back or press Q.

•Contacts: A phonebook of nine stored numbers

for the speed dialing function. The number in

memory location 9 is the number for the ANAC

function.

TS®54 TDR Test Set Users Card

•Call Log: A list of phone numbers for the last 10

calls that the test set made or received.

•Digit Grab: Shows you the digits dialed by

another device.

•SmartTone: Lets you use an inductive probe to

find telephone lines.

•EditContact: Lets you edit numbers in the

phonebook.

•TDR: Lets you change the Line Verification and

VOP settings for the TDR.

•Settings:

•Bklt Time: Backlight timeout

•Handset Vol, Spkr Vol: Handset and speaker

volume.

•Tone/Pulse: Select tone or pulse mode

•Pause Time Flash Time: Duration for pause and

flash.

•SpkrPhone: Default mode for the speakerphone.

Two-Way: microphone is on.

RecivOnly: microphone is off.

•AutoShutOff: Power-down timeout.

•FactDfaults: Select factory defaults.

Visual ANAC mode (For service provider use only.

Visual ANAC is not available in all regions.)

Connect the test set to a working telephone

line. Press P. Press R$. The display shows

Dial ANAC. Dial the ANAC number.

If you put the ANAC number into location 9 in

the Call Phonebook, the test set goes into visual

ANAC mode and dials the ANAC number when

you press R9.

Caller ID Messages

• The incoming phone number

•Blocked ID: CID is blocked

•Line error: CID data is incomplete

•Unknown ID: CID is not available

TDR

The TDR lets you measure the length of cables

and the distance to the first open or short on

cables as long as 3,000 ft (914 m). Optional: Turn

on the Line Verification (Line Verif) function

and set the velocity of propagation (VOP) to the

correct value for the cable. The Line Verification

function does tests for data and voltage on the

line when you press t.

Press Q. Connect the test leads to the cable.

Press t.

TDR Results

•Short at 1267 ft: There is a short across the two

conductors 1267 feet from the test set.

•Open at 2433 ft: The cable is 2433 feet long, or

there is an open in one or both of the

conductors 2433 feet from the test set.

•TDR Voltage Detect Lockout: There is data or

voltage on the line. The TDR does not operate

on an active line.

Andere Fluke Prüfgeräte Handbücher

Fluke

Fluke 190 Series II Bedienungsanleitung

Fluke

Fluke 1623 Bedienungsanleitung

Fluke

Fluke LinkIQ Bedienungsanleitung

Fluke

Fluke CertiFiber Bedienungsanleitung

Fluke

Fluke 718 Series Bedienungs- und Montageanleitung

Fluke

Fluke 810 Bedienungsanleitung

Fluke

Fluke 5522A Operators Bedienungsanleitung

Fluke

Fluke 525A Bedienungsanleitung

Fluke

Fluke 5730A Bedienungsanleitung

Fluke

Fluke NetTool II Series Bedienungsanleitung

Fluke

Fluke NETWORK SERVICE MODULE DTX-NSM Bedienungsanleitung

Fluke

Fluke 700PTP Bedienungsanleitung

Fluke

Fluke 741B Bedienungsanleitung

Fluke

Fluke FIBER QUICKMAP Bedienungsanleitung

Fluke

Fluke 5502A Bedienungsanleitung

Fluke

Fluke 753 Bedienungsanleitung

Fluke

Fluke 753 Gebrauchs- und Pflegehandbuch

Fluke

Fluke 5500A Bedienungsanleitung

Fluke

Fluke 9144 Bedienungsanleitung

Fluke

Fluke MicroScanner MS-POE Bedienungsanleitung

Fluke

Fluke 150X Series Gebrauchs- und Pflegehandbuch

Fluke

Fluke 975 AirMeter Montage- und Bedienungsanleitung

Fluke

Fluke 9040 Betriebsanleitung

Fluke

Fluke i400s Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung