FlyTech POS455 Bedienungsanleitung
USER MANUAL
VERSION 1.1 September 2018
POS455
Hardware System
ii
Copyright 2018
All Rights Reserved
Manual Version 1.1
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose.
We shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated
to another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation
to ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register or in a built-in installation
unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
WRXFKGDQJHURXVYROWDJHSRLQWVRUVKRUWRXWSDUWVWKDWFRXOGUHVXOWLQDÀUHRUHOHFWULF
shock. Never spill liquid of any kind on the product.
iii
CE MARK
This device complies with the requirements of the EEC directive 2014/30/EU with
regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery
according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
OHJLVODWLRQSHULSKHUDOVVKDOOEH´0DWHULDOVIRUÀUHHQFORVXUHµFRPSOLDQW
0DWHULDOVIRUÀUHHQFORVXUHV
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a
),5((1&/2685(LQWKHWKLQQHVWVLJQLÀFDQWZDOOWKLFNQHVVXVHGVKDOOEHRI9&/$66
MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY
EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall
thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1
iv
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centers for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
RUWKHLUORFDOJRYHUQPHQWRIÀFHIRUGHWDLOVRIZKHUHDQGKRZWKH\FDQWDNHWKLVLWHPIRU
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
v
Revision Description Date
1.0 • Initial release September 2017
1.1 • D36 V4.0 MB added
• D86S MB added September 2018
Revision History
Changes to the original user manual are listed below:
vi
Table of Contents
1. Packing List..................................1
1-1. Standard Accessories.....................................................1
1-2. Optional Accessories.......................................................2
2. System View..................................3
2-1. Front & Side View............................................................3
2-2. Rear View.........................................................................3
2-3. IO Ports View....................................................................4
2-4. System Dimensions ........................................................5
3. System Assembly & Disassembly6
3-1. Disassemble the Stand ..................................................6
3-2. Remove the Cable Cover ................................................6
3-3. Install the Power Adapter................................................7
3-4. Replace HDD...................................................................7
4. Peripheral Installation.................8
4-1. Install the MSR Module..................................................8
4-2. Install the Fingerprint Module........................................9
4-3. Install the iButton Module.............................................10
4-4. Install the Customer Display..........................................11
4-5. Install the Second Display ............................................12
4-6. Cash Drawer Installation ...............................................13
vii
6SHFLÀFDWLRQ................................15
&RQÀJXUDWLRQ...............................17
6-1. D36 V2.1 Motherboard..................................................17
6-1-1. Motherboard Layout........................................................17
6-1-2. Connectors & Functions .................................................18
6-1-3. Jumper Setting................................................................19
6-2. D36 V4.0 Motherboard..................................................21
6-2-1. Motherboard Layout........................................................21
6-2-2. Connectors & Functions .................................................22
6-2-3. Jumper Setting................................................................23
6-3. D86U Motherboard........................................................24
6-3-1. Motherboard Layout........................................................24
6-3-2. Connectors & Functions .................................................25
6-3-3. Jumper Setting................................................................26
6-4. D86S Motherboard........................................................28
6-4-1. Motherboard Layout........................................................28
6-4-2. Connectors & Functions .................................................29
6-4-3. Jumper Setting................................................................30
Appendix: Drivers Installation..........31
viii
The page is intentionally left blank.
1
a. System
b. Power adapter
c. Power cord
d. RJ45-DB9 cable (x2)
e. Driver bank
Note: Power cord will be supplied differently according to various region or country.
1. Packing List
1-1. Standard Accessories
ab
cd
e
2
a. MSR module
b. Fingerprint module
c. iButton module
d. Customer display
e. 8.4" 2nd display
1-2. Optional Accessories
ab
cd
e
Inhaltsverzeichnis
Andere FlyTech Touch-Terminal Handbücher
Beliebte Touch-Terminal Handbücher anderer Marken
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung
Ingenico
Ingenico AXIUM EX4000 Bedienungsanleitung
Heisei Electronics
Heisei Electronics Q-POS 815 Bedienungsanleitung
Amano
Amano MTX-15 Bedienungsanleitung
FLOWBIRD
FLOWBIRD CWT Compact Touch Bedienungsanleitung
Demco
Demco SP7 Bedienungsanleitung
Motorola
Motorola MTP850 Bedienungsanleitung
YASKAWA
YASKAWA 62H-MDC0 Bedienungsanleitung
MVG industries
MVG industries NeptuLink Bedienungsanleitung
Price Industries Limited
Price Industries Limited FDC Gebrauchsanweisung
Honeywell
Honeywell TemaKey Bedienungsanleitung
EBN
EBN BPC65-B-A16G Bedienungsanleitung