Focal Point F820680 Programmierhandbuch

ASSEMBLY & INSTALLATION INSTRUCTIONS

All instructions must be handed to the user for

safekeeping.

Please note : Except where otherwise stated, all rights, including copy-

right in the text, images and layout of this booklet is owned by Focal

Point Fires plc. You are not permitted to copy or adapt any of the con-

tent without the prior written permission of Focal Point Fires plc.

Revision A - 09/15

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330

Fax: 01202 499326

www.focalpointfires.co.uk

e : [email protected].uk

Questions or problems with your appliance?

Don’t take it back to the store

just give us a call on 01202 588601 we’re here to help

lines open between 9am and 5pm, onday to Friday

MODELS COVERED BY THESE INSTRUCTIONS

F820680 FPFB 553 MONTANA FIRE SURROUND WHITE

A S S E M B L Y I N S T R U C T I O N S

GB IE

1.0 IMPORTANT NOTES

Section

1.0

2.0

3.0

4.0

5.0

6.0

7.0

Contents

Important notes

Tools required

Hardware & parts list

Assembly

Installation

Cleaning/ finishing

Guarantee - terms and conditions

Page No.

2.0 TOOLS RE UIRED

CODE NA E FIGURE QUANTITY

ASCREWS

(8x 25mm)

16PCS

B SCREWS

(8x 45mm)

9PCS

WOOD

DOWELS

(8x 30mm)

16PCS

D SCREWS

(6x 20mm)

4PCS

WALL

SCREWS

(6x 38mm) 2PCS

WALL

PLUGS

(6x 25mm)

2PCS

IRROR

PLATES

(45x 43mm)

2PC

3.0 HARDWARE & PARTS LIST

CODE NA E FIGURE QUANTITY

①TOP PANEL 1PC

②LEFT LEG 1PC

③RIGHT LEG 1PC

④

NARROW

INSIDE

PANEL

3PCS

⑤

CONNECT-

ING

BLOCK 4PCS

To ensure safe and stable installation:

1. The assembled Fire Surround must be fixed / secured to wall.

2. The wall must be sturdy and in good repair.

3. Some walls require alternative fixings (not included).

4. When drilling into the wall, check for hidden pipes and cables.

5.There are two options for construction of this surround.

A - with rebates - If you are installing this surround with a gas fire, or an electric fire where there is space in the wall to recess

the fire, this means the laminate / marble is up against the wall.

B - with out rebates - If using this surround with an electric fire and a flat wall you will need to remove the rebates, instead use

the spacer frame from the fire.

Cross head screwdriver PZ2 (3 inches in length or greater)

Drill, 6mm and a 2mm suitable drill bit

Pencil

Tape measure

4.0 ASSEMBLY

GB IE

Screw the 4x connecting blocks (5) onto the rear of the left leg (2) and the right leg (3) with the 8x 25mm screws (A) provid-

ed.

Fixings Parts

A x 8 PCS 2

STEP 1

Fixings Parts

A x 8 PCS 1

C x 4 PCS 2

Next insert the 4x wood dowels (C) into the top of the left leg (2) and the right leg (3). Carefully place the top panel (1) on to

the top of the left and right hand legs (2 and 3). Ensuring the top (1) lines up with the 4x connecting blocks (5) and the 4x

wooden dowels (C). Once in place, screw the 8x 8x 25mm screws (A) through the connecting blocks (5) and into the top

panel (1) securing it into position.

STEP 2

⑤

4.0 ASSEMBLY

GB IE

Fixings Parts

B x 9 PCS 1

C x 12 PCS 2

STEP 3

If using option A only. If rebates are not being used go to section 5.

If a 75mm rebate (4) is required. CAREFULLY! lay the surround on a soft flat surface, taking extra care that you do not scratch

the front of the surround. NEVER DRAG THE SURROUND! Insert the 12x wooden dowels (C) into the rear of the top panel

(1), the left leg (2) and the right leg (3). With the rebates (4) in the correct orientation, place the 3x rebates (4) into position

over the wooden dowels (C). Screw the 9x 8x 45mm screws (B) through the rear of the rebates (4) connecting them to the

surround.

5.0 INSTALLATION

With a pencil mark out the desired height where you would like the mirror brackets (G) to be situated on the rear of the legs. To avoid

splitting the leg, pre drill the bracket holes with a 2mm drill bit. Now attach the brackets to the legs using the screws (D). Once the

brackets are in position, centre and level the hearth into its final fitting position. Position the surround on the hearth to correspond with

the header/fireplace lintel, mark with a pencil on the wall where you wish to drill. Remove the surround and prepare the wall from the

marked positions. If using the fixings supplied, drill a hole in the wall using a 6mm drill bit. If not, use a suitable drill bit for the wall plugs

you are using. Insert the wall plugs (F) into position. Offering the surround back up into position against the wall, you are now able to

secure the surround to the wall using the screws (E).

Fixings

D x 4 PCS

E x 2 PCS

F x 2 PCS

G x 2 PCS

①

②

③

⑤

Before carrying out any of the following operations, ensure that the appliance is OFF and completely cold. Regularly clean

around the appliance to ensure that dust, fluff, pet hair etc, are kept to a minimum. There are no other specific requirements for

care, other than regular cleaning of the general appliance.

A wipe with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Test on a hidden

part before cleaning. Clean only in the direction of the grain. Regularly check the surround is securely fixed in position.

6.0 CLEANING/ FINISHING

7.0 GUARANTEE - TERMS AND CONDITIONS

The 3 year guarantee commences from the date of purchase, provided that the terms and conditions are adhered to:

Registration is not required.

1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your

proof of purchase.

Making a claim is easy.

If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then

please submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you

can email or fax. Please note that this does not affect your statutory rights.

Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.

Alternatively email: 3g@focalpointfires.co.uk or fax. 01202 499326.

Details required:

1. Name, full address including post code and contact telephone number.

2. Receipt of purchase or credit card statement.

F861316

As our policy is one of continuous improvement and development, we hope therefore you understand we must retain the right to amend details and/or specifications without prior notice.

GB IE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Focal Point Kaminzubehör Handbücher

Focal Point

Focal Point DS-FS22 Programmierhandbuch

Focal Point

Focal Point F820586 Programmierhandbuch

Focal Point

Focal Point Durham Pine Bedienungsanleitung

Focal Point

Focal Point FPFBQ395 Gebrauchsanweisung

Focal Point

Focal Point MONTANA FPFBQ553 Programmierhandbuch

Focal Point

Focal Point F820936 Programmierhandbuch

Focal Point

Focal Point EASTON LED ELECTRIC SUITE Programmierhandbuch

Focal Point

Focal Point F820583 Programmierhandbuch

Focal Point

Focal Point MONTANA Programmierhandbuch

Focal Point

Focal Point NEBRASKA SURROUND WALNUT VENEER Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Valor

Valor L2 1700K Bedienungsanleitung

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung