Focal Point BCD-85U Bedienungsanleitung

All instructions must be handed to the user for

safekeeping.

Please note: Except where otherwise stated, all rights,

including copyright in the text, images and layout of this

booklet is owned by Focal Point Fires plc. You are not

permitted to copy or adapt any of the content without

the prior written permission of Focal Point Fires plc.

Revision A - 08/17

BCD-85U

Under Counter Fridge Freezer

wner’s Instructions GB IE

Focal Point Fires plc.

Christchurch, Dorset BH23 2BT

Tel: 01202 499330 ption 5

Fax: 01202 499326

www.focalpointfires.co.uk

e : sales@focalpointfires.co.uk

M DELS C VERED BY THESE INSTRUCTI NS

BCD-85U Under Counter Fridge Freezer

N TE: Before discarding an old appliance switch off and disconnect it from the power supply. Cut off and

render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be

undertaken by a competent person. Disable any door lock to make sure that children cannot get stuck inside

the appliance.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for

the environment and human and health, which could otherwise be caused by inappropriate waste handling of

this appliance.

The symbol shown in figure 1 on the product or on the documents accompanying the product indicates that this appliance may not

be treated as household waste. Instead it shall be handed over to the applicable collection point for recycling of electrical and

electronic equipment.

Disposal must be carried out in accordance with the local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local authority household

waste disposal service or the shop where you purchased the product.

Your safety is of the utmost important to F CAL P INT.

Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of

the information contained in this booklet, please phone the F CAL P INT advice line.

IMP RTANT: Any installation work must be carried out by a qualified electrician or competent person.

Use of the appliance

Your appliance is only designed to be used in the home. It is suitable for storing food that needs to be chilled and refrigerated. If it is

used for any other purpose or it is not used correctly, F CAL P INT will accept no liability for any damage that may be caused.

Altering the specifications of the appliance must not be attempted for reasons concerning your safety.

Before using the appliance

Check the appliance for any signs of transport damage. If you notice any damage then you should not connect the appliance to the

main power supply, also contact the manufacturer.

Transportation and Handing

For safe lifting, tilt the appliance backwards by no more than 45 degrees, hold the base and rear corners of cabinet. Lift the appliance

carefully.

Never use the door handles for lifting.

I N S T A L L A T I N I N S T R U C T I N S

1.0 ENVIR NMENTAL

Section

1.0

2.0

3.0

4.0

5.0

6.0

Contents

Environmental

Important Safety Information

Technical Specification

Using Your Appliance

Freezer Tips

Care & aintenance

Page No.

Section

7.0

8.0

9.0

9.1

9.2

10.0

Contents

Reversing the Doors

Cleaning & aintenance

Installation

Electrical Connection

Positioning

Troubleshooting

Page No.

2.0 IMP RTANT SAFETY INF RMATI N

Figure 1

Refrigeration

Your appliance contains R600a Refrigerant, which is a natural gas that does not contain CFC’s that can damage the environment.

However it is a flammable substance, therefore care should taken:

During the transportation and installation of the appliance make sure that the refrigeration pipework does not get damaged.

If it does become damaged then sources of ignition and open flames should be avoided, also the room that the appliance is situated in

should be thoroughly ventilated.

Do not place any objects on top of the appliance as this may damage the top and block up the required ventilation.

Child Safety

Packaging materials should be kept away from children.

Children should not be allowed to touch the controls or play with the appliance.

General Safety

Do not pull out or insert the plug with wet hands.

Do not attempt to use the appliance outdoors or any place where it is likely to come into contact with the elements.

Before cleaning the appliance or performing maintenance work, ensure that the appliance has been disconnected from the mains

supply.

Never allow the back coils of the appliance to come into contact with the wall surface.

Always ensure that the location where you are installing your appliance is free of stored items such as papers and other flammable

materials.

Do not place electrical devices inside of the appliance such as mixers.

Service

You should not attempt to repair the appliance yourself, as this could cause injury or a more serious malfunction. If you require a

service call then please contact the manufacturer.

Note: Figures in the user manual are only for reference. The actual product may differ slightly.

2.0 IMP RTANT SAFETY INF RMATI N - C NTINUED

GB IE

3.0 TECHNICAL SPECIFICATI N

Model BCD-85 U

Description of appliance Double Door

Type/appliance Refrigerator

Installation of Appliance Free Standing

Aesthetics

Door profile Rounded

Handle Integrated

Available colours White/Silver

Basic features

Energy efficiency class A+

Climate class (R600a:N=16~32°C, ST=18~38°C N,ST

Climate class (R134a ST=18~38°C, T=18~43°C)

Freezer compartment star rating 4

Gross capacity (L) 75

Net capacity (L) 71

Net capacity fridge compartment (L) 49

Net capacity freezer compartment (L) 22

Energy consumption (kWh/year) 161

Freezing capacity / 24 hours 2.5

ax noise level 42

ax storage time from no power (hours) 13

Kind of coolant R600a

Foaming components C-P

Certifications CE/GS

Key features

Cooling system: Compressor

Number of compressor(s) 1

Defrosting Fridge / Freezer anual

Control system echanical

NO FROST (Fridge/Freezer) No/No

Wind Air System No

Bacteria Proof System No

Energy efficiency class

Energy class: A+

*Please refer to the installation instructions for more specific information on the size of aperture that you will require.

Important: when you install the appliance it is important to bear in mind its climate class.

In order to find out the climate class of the appliance you should check the rating plate.

3.0 TECHNICAL SPECIFICATI N - C NTINUED GB IE

Before switching on. ake sure that it has been installed by a suitably qualified person, as per the information contained in

FOCAL POINT’s installation instructions.

After delivery, wait for four hours before connecting the appliance to the mains supply. This will allow any refrigerant gasses that may

have been disturbed during the transportation process to settle.

The outside of the appliance and the removable accessories contained within it should be cleaned with a solution of liquid detergent

and water.

The interior of the appliance should be cleaned with a solution of sodium bicarbonate dissolved in lukewarm water. The interior and

accessories should be thoroughly dried after the cleaning process has been completed.

There may be an odour when you first switch on the appliance. It will lessen as the appliance starts to cool.

Setting the temperature

The temperature in the appliance is controlled by the temperature control knob located behind the

freezer drawers. Rotate the control knob left or right to regulate the temperature inside the freezer.

On the temperature control, 1 is the warmest setting and 7 is the coldest setting. Under normal

conditions the temperature control should be set between 3 and 4.

Once the temperature control has been set, close the door and plug in the appliance. We recommend

that the door is not opened for a minimum of 2.5 hours to allow the appliance to reach standard

operating temperature.

Note: The standard operating temperature for the freezer compartment should be between -18°C and

-25°C.

Figure 2

4.0 USING Y UR APPLIANCE

Control panel

External control display No

External control display with LCD No

Temperature range (from>to) R:0~8 F: ＜-18

Super Cooling (Fridge) No

Super Freezing (Freezer) No

Holidays function (Stand-by) No

ECO function No

Over temperature alarm No

Adjustable thermostat Yes

Control lamps No

Basics datas

Unit dimensions ( W / D / H ) 480x445x845

Depth with open door 90

Net weight 24.0

Voltage / frequency 220-240V/50Hz

mains fuse (intensity) 0.8

Input power R600a (A, A+, A++) 90

Input power R134a 120

Fridge compartment

Shelves:

Number/type 1/glass

Colour transparent

Shelf (on salad crisper) Yes/glass

Crisper(s):

Number / colour 1/ Transparent

Door:

Storage rack(s) (Total) 2

Butter and cheese compartment No

Inside colour White

Reversible door Yes

Lock Optional

Freezer compartment

Drawer(s) No

Shelve(s) No

Flap(s) No

Colour of drawer No

Shelf in the Freezer No

Door rack(s) No

Accessories

Defrost water outlet Optional

Interior light Yes

Special ice maker No

Ice cube tray(s) 1

Eggs tray(s) / Total number of eggs 1

Adjustable feet (front / rear) 2/0

Castors (front / rear) No

Wall spacer grid or distance holder Optional

Condensor Internal/ External

Lenght of cable/incl. plug (mm) 126

Packing dimensions

Packing dimensions ( W / D / H ) 500x465x870

Gross weight (kg) 26

Storage of Frozen food

• Fresh foods such as fish and meat can be frozen to maintain freshness, and keep the nutrients in the food.

• Wrap food to be frozen or place it in an airtight container.

• Do not allow already frozen food into direct contact with food to be frozen.

• Ready frozen food should be placed it in freezer as soon as possible.

• Do not re-freeze food once it has thawed.

Defrosting

We recommend this is done once or twice a year or when the ice formation is 3-4mm thick.

1. Switch the appliance off at the wall socket and remove the plug.

2. Wrap frozen food in layers of newspaper or blankets

3. Keep the freezer door open.

4. Place a suitable container to collect the defrost water.

5. Place a bowl of hot (not boiling) water in the freezer to speed defrosting.

6. Use a plastic or wooden implement to gently scrape ice.

7. After defrosting, clean and dry the interior.

8. Switch the appliance on and replace any frozen food.

Never use sharp metal tools, you will damage the appliance.

Never use an electric heater to raise the temperature.

The Freezer has the capability of opening the door from either the left or the right side. The unit is delivered to you with the door

opening from the left side.

We strongly recommend that this task is performed by 2 people to avoid any injury or damage.

Ensure the appliance is unplugged and all contents have been removed.

Tools required

• Phillips head screwdriver

• Flat head screwdriver

• Hexagonal spanner

5.0 FREEZER TIPS

6.0 CARE AND MAINTENANCE

GB IE

7.0 REVERSING THE D RS

1.Remove the right top hinge cover.

2. Remove the top-hinge with a phillips screwdriver or a spanner.

7.0 REVERSING THE D RS - C NTINUED GB IE

3. Remove the door limit block from the bottom for the door with a screwdriver and refit on the opposite side.

Limit block

4. Remove the bottom door hinge pin fixing bracket with a screwdriver or a spanner. After the fixing bracket is removed it

will need to be fitted on the opposite side of the appliance. The bottom hinge pin fixing bracket is located underneath the

appliance and you need to tilt the appliance backwards to remove the bracket.

5. Remove the bottom door bush bearing and the limit block and refit on the opposite side.

6. Remove the screw hole covers.

IMP RTANT: The screw cap and screw hole covers should be retained for use on the opposite side of the appliance.

7.0 REVERSING THE D RS - C NTINUED GB IE

7. Remove the middle door hinge and refit on the opposite side.

8. Correctly position the bottom door and then secure the middle hinge. Note: Always put the bottom door on first.

10. Refit the top-hinge with a phillips screwdriver or a spanner on the opposite side from it’s original position.

9. Use a spanner to remove the pin from the top hinge pin fixing bracket. Then turn the hinge pin bracket over and refit the

hinge pin with a spanner.

Disconnect the appliance from the mains supply.

Leave the door to the freezer compartment open. You can place a bowl of warm water inside the freezer compartment to speed up

to defrost process.

Once all the ice that has built up has melted then inside of the freezer compartment should be dried thoroughly. Failure to do this

will result in immediate ice build-up when the appliance is turned back on.

With dry hands, reconnect the appliance to the mains supply. Set the temperature display to it’s maximum setting or switch on the

super frost setting for 24 hours.

You should not attempt to freeze fresh food inside the freezer compartment until this 24 hour time period has elapsed.

Once the 24 hour period has elapsed, you should set the temperature display to its normal operating temperature or switch off the

super frost setting.

Do not defrost the appliance with other electrical devices (e.g. hair dryers). Do not use sharp metal objects to

remove the ice on the freezer, as this could cause damage to the refrigeration system.

7.0 REVERSING THE D RS - C NTINUED GB IE

8.0 CLEANING AND MAINTENANCE

9.0 INSTALLATI N

IMP RTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the

frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The

rating plate can be found on the front left edge of the inside edge of the refrigerator.

The manufacturer declines all responsibility in the event of the installer failing to observe all the accidental prevention regulations in

force, which are necessary for use and the regular operation of the electric system.

Electrical Connections

THE FRIDGE/FREEZER IS INTENDED F R FITTED AND PERMANENT INSTALLATI N.

We recommend that the appliance is connected by a qualified electrician who is a member of the N I C E I C and who will comply

with the I.E.E. and local regulations.

Your refrigerator comes supplied with a 13 amp plug fitted. If in future you need to change the fuse in the plug then a 13 amp ASTA

approved (BS 1362) fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED!

11. Refit the top hinge cover.

12. Correctly position the top door and then secure the top hinge.

13. Install the four screw caps and two catches to corresponding position.

Ensure the Appliance is unplugged and empty.•

Adjust the two leveling feet to their highest position.•

We recommend you have someone to assist you.•

14. Replace the leveler to the other side and adjust it to make sure the cabinet is level.

The wiring in the mains lead is coloured as follows:

Brown Live

Blue Neutral

Green and yellow Earth

As the colours of the wires in the appliance’s mains lead may not correspond with coloured markings identifying the terminals in your

spur box, please proceed as following:

The Brown wire must be connected to the terminal marked “L” (Live) or coloured Red.

The Blue wire must be connected to the terminal marked “N” (Neutral) or coloured Black.

The Green and Yellow wire must be connected to the terminal marked “E” (Earth), or by the earth symbol or coloured Green

and Yellow.

When the connection is completed no stray strands or cut wire should be present. The cord clamp must be secured over the outer

sheath.

It is advised that the appliance is only installed in a location where the ambient temperature of the room, corresponds with the

climate classification that is stated on the rating plate of the appliance. The appliance may not function correctly if the ambient

temperature falls outside of the following ranges.

The appliance should not be located in direct sunlight or exposed to continuous heat or extremes of temperature (e.g. next to a

radiator or boiler).

The door should be able to open completely and freely.

The appliance should be situated so the food stored inside can be easily accessed.

Check whether there is an electrical socket available, which will be accessible after the appliance is installed.

Place the fridge in a location with a firm base. In order to prevent vibration and noise, the freezer must be levelled by adjusting the

front feet.

Choose a well ventilated location with no less than 10cm clearance around the freezer.

9.1 ELECTRICAL C NNECTI N GB IE

Climate Classification Appropriate Ambient Temperature

SN + 10 to + 32 degrees centigrade

N + 16 to + 32 degrees centigrade

ST + 18 to + 38 degrees centigrade

9.2 P SITI NING

IMP RTANT: If the fridge/freezer appears not to be operating properly, before contacting the manufacturers please

refer to the checklist below.

My fridge/freezer does not appear to be working/there is no power to my appliance.

Check that the plug is fully inserted into the power socket.•

Check that there is power to the mains supply (e.g. there hasn’t been a power cut or that the fuse hasn’t blown).•

Check that the display has not been turned to the off position.•

Check that your mains supply voltage corresponds to the voltage stated on the rating plate of the appliance.•

My Fridge/freezer appears to be performing poorly.

Check that the appliance isn’t overloaded and that food hasn’t been packed too tightly into it•

The thermostat setting is too high i.e. (9) degrees then you should turn the thermostat down i.e. (4) degrees.•

Ensure that there is adequate ventilation for your appliance.•

My Fridge/freezer is noisy

The refrigerant gas that circulates the pipework of the appliance may make a slight noise even if the compressor is not running.•

If the noise worsens or the appliance gets louder than normal; check that it is levelled off correctly, that nothing is touching the•

rear of the fridge freezer and that nothing placed inside the appliance is rattling.

Ice has formed on the inner back wall of my fridge

Please check that food has not been pushed too far back inside the appliance so that it is in contact with the inner back wall.•

Please check that food has not been pushed up against the thermostat. The thermostat is on the right hand side, having food too•

close to the thermostat will affect the temperature of the fridge.

IMP RTANT: if you run the appliance with the temperature controls on lower settings for prolonged periods, the defrost drain•

hole will freeze. It may also cause the appliance to overwork and the fridge and freezer sections to freeze over.

The seal must adhere properly all the way around the door

If either seal is not adhering to the cabinet properly then you should either.

1.Use a warm damp cloth and manipulate the seal until it does adhere to the cabinet properly all the way around the door.

2.Use a hair dryer on its lowest heat setting and lightly heat the areas of the door seal that are not adhering correctly. The heat will

make the seal more pliable and this will allow you to manipulate the seal into the correct position.

IMP RTANT: nly use the lowest setting of the hair dryer and do not heat the seal for long periods of time

otherwise irreversible damage may be caused and this will not be covered by your guarantee.

IMP RTANT: It is normal to get some ice droplets forming on the back of the appliance. The formation of ice droplets does•

not indicate an appliance fault.

D N T ATTEMPT T REPAIR THE APPLIANCE Y URSELF.

Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not of an

appliance fault, then you may be liable for the cost of the call out charges.

The appliance must be accessible for the engineer to perform any necessary repair. If your appliance is installed in such a way that an

engineer is concerned that damage will be caused to the appliance or your kitchen then they will not complete a repair.

This includes situations where appliances have been tiled in, sealed in with sealant, have wooden obstructions placed in front of the

appliance like plinths or any installation other than the one specified by FOCAL POINT has been completed.

10.0 TR UBLESH TING GB IE

F861458

Inhaltsverzeichnis

Andere Focal Point Kühlschrank Handbücher

Focal Point

Focal Point HD-172W Montageanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung