FOLSOM Blend PRO BP-2002 Einrichtungshandbuch
INSTALLATION AND OPERATOR’S MANUAL
Model BP-2002
Blend PRO – Wide Screen Image Processor
Manual #26-0206000-00 / Revision B
RECORD OF CHANGES
REV #
DATE
ECO #
DESCRIPTION
Approved By
A
939
Released A. Yerocostas
B 5/6/03 1050 Front panel menu changes:
- Added black level adjustment and removed
halo removal submenu to Output Image
Adjust menu.
- Added input source menu item to System
Options menu.
Remote command changes:
- Removed remote debug commands.
- Added seam removal threshold.
- Added input clamp gate position and width.
- Added input sync-on-green threshold.
- Added rear panel DAC threshold.
- Added rear panel input select.
Removed halo adjustment instructions.
Updated BlendPRO Rear Panel figure 2-1.
A. Yerocostas
Manual # 26-0206000-00
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top
cover will expose dangerous voltages. To avoid personal injury, do not
remove the top cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not
apply more than 230 volts rms between the supply conductors or
between both supply conductor and ground. A protective ground
connection by way of grounding conductor in the power cord is essential
for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power
cord. To avoid electrical shock, plug the power cord into a properly wired
receptacle before connecting to the product input or output terminals.
A protective-ground connection by way of the grounding conductor in the
power cord is essential for safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use
only a power cord that is in good condition. Refer cord and connector
changes to qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage
rating, and current rating characteristics. Refer fuse replacement to
qualified service personnel.
Do Not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an explosive
atmosphere.
Terms In This Manual and Equipment Marking
Highlights an operating procedure, practice,
condition, statement, etc., which, if not strictly
observed, could result in injury to or death of
personnel.
NOTE Highlights an essential operating procedure,
condition or statement.
CAUTION
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
AVERTISSEMENT!
Le point d´exclamation dans un triangle equilatéral signale
à alerter l´utilisateur qu´il y a des instructions d´operation
et d´entretien tres importantes dans la litérature qui
accompagne l´appareil
WARNING
VORSICHT ein Ausrufungszeichen innerhalb eines gleichwinkeligen
Dreiecks dient dazu,
den Benutzer auf wichtige Bedienungs-und
Wartungsanweisungen in der Dem
Great beiliegenden Literatur aufmerksam zu machen.
BlendPROQuick Start Guide
1. Equipment Setup
Connect the image sources, BlendPRO and projection devices as required for the application. A typical 4 screen
system is shown above. Turn the equipment on. Connect a laptop with the BlendWizard application installed to the
Controller Console Port. For detailed instructions on how to install the BlendWizard to your laptop please refer to
Chapter 2; BlendWizard Installation instructions.
2. System Configuration and Adjustments
The BlendWizard will walk you through the series of steps required to configure and adjust the system. The steps are
outlined below for reference, however, much of the process is automated by BlendWizard. For detailed explanations
please refer to Chapter 2; Detailed instructions for configuring a wide screen Presentation.
STEP 1: Projector Clock Phase Adjustment
STEP 2: Projector Horizontal and Vertical Sampling Adjustments
STEP 3: Projector-to-Projector Color Balance Adjustment
STEP 4: Projector Registration (Overlap and Geometry Adjustment)
STEP 5: Output Black Level Adjustment for Non-Overlapped Region
STEP 6: Configure BlendPRO for 1:1 Sampling (Input Clock Phase and Horiz. Position Adjustments)
STEP 7: Source-to-Source Color Balance
STEP 8: Turn on Data Doubling
STEP 9: Feathering transfer function adjustment
This is a quick reference guide. For detailed information on the BlendPRO, please refer to the
Installation and Operating Manual supplied with your unit.
Folsom Research, Inc.
•
11101-A Trade Center Drive, Rancho Cordova CA 95670
•
(916) 859-2500
•
www.folsom.com
Inhaltsverzeichnis
Andere FOLSOM Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
