FOR-A MBP-100PD Series Bedienungsanleitung

MBP-100PD Series

Clip Server (Baseband Converter)

MBP-100PD16G

MBP-100PD64G

MBP-100PD128G

2nd Edition

OPERATION

MANUAL

Edition Revision History

Edit. Rev. Date Description Section/Page

1 - 2010/05/07

2 - 2012/09/21 "Notes on Using The MBP-100PD" added

"Genlock Settings" changed

"How to Change Network Settings" added

Specifications changed (video formats, etc. )

Sec. 1-3

Sec. 3-3

Sec. 4

Sec. 5-1

Precautions

Important Safety Warnings

[Power]

Operate unit only on the specified supply voltage.

Disconnect power cord by connector only. Do not pull on cable portion.

Do not place or drop heavy or sharp-edged objects on power cord. A damaged cord

can cause fire or electrical shock hazards. Regularly check power cord for

excessive wear or damage to avoid possible fire / electrical hazards.

[Grounding]

Ensure unit is properly grounded at all times to prevent electrical shock hazard.

Do not ground the unit to gas lines, units, or fixtures of an explosive or dangerous

nature.

Ensure power cord is firmly plugged into AC outlet.

[Operation]

Do not operate unit in hazardous or potentially explosive atmospheres. Doing so

could result in fire, explosion, or other dangerous results.

Do not allow liquids, metal pieces, or other foreign materials to enter the unit. Doing

so could result in fire, other hazards, or unit malfunction.

If foreign material does enter the unit, turn power off and disconnect power cord

immediately. Remove material and contact authorized service representative if

damage has occurred.

[Transportation]

Handle with care to avoid shocks in transit. Shocks may cause malfunction. When

you need to transport the unit, use the original packing materials or alternate

adequate packing.

Stop

Caution

Hazard

Caution

Hazard

Caution

[Circuitry Access]

Do not remove covers, panels, casing, or access circuitry with power applied to the

unit! Turn power off and disconnect power cord prior to removal. Internal servicing /

adjustment of unit should only be performed by qualified personnel.

Do not touch any parts / circuitry with a high heat factor.

Capacitors can retain enough electric charge to cause mild to serious shock, even

after power is disconnected. Capacitors associated with the power supply are

especially hazardous. Avoid contact with any capacitors.

Unit should not be operated or stored with cover, panels, and / or casing removed.

Operating unit with circuitry exposed could result in electric shock / fire hazards or

unit malfunction.

[Potential Hazards]

If abnormal smells or noises are noticed coming from the unit, turn power off

immediately and disconnect power cord to avoid potentially hazardous conditions. If

problems similar to above occur, contact authorized service representative before

attempting to again operate unit.

[Rack Mount Brackets, Ground Terminal, and Rubber Feet]

To rack mount or ground the unit, or to install rubber feet, do not use screws or

materials other than those supplied. Otherwise, it may cause damage to the internal

circuits or components of the unit. If you remove the rubber feet attached on the unit,

do not reinsert the screws securing the rubber feet.

[Consumables]

The consumables used in unit must be replaced periodically. For further details on

which parts are consumables and when they should be replaced, refer to the

specifications at the end of the Operation Manual. Since the service life of the

consumables varies greatly depending on the environment in which they are used,

they should be replaced at an early date. For details on replacing the consumables,

contact your dealer.

Caution

Hazard

Stop

Caution

Upon Receipt

Unpacking

MBP-100PD units and their accessories are fully inspected and adjusted prior to shipment.

Operation can be performed immediately upon completing all required connections and

operational settings.

Check your received items against the packing lists below.

ITEM QTY REMARKS

MBP-100PD16G

MBP-100PD64G

MBP-100PD128G

AC Cord 1 set

Rack Mount Brackets 1 set EIA standard type

Rubber Feet 1 set

Operation Manuals 2 MBP-100PD Operation Manual (This manual)

MCS-MBPPON Operation Manual

IMPORTANT

Wait at least 10 seconds before turning back on the power of MBP-100PD after it is

powered off.

Check

Check to ensure no damage has occurred during shipment. If damage has occurred, or items

are missing, inform your supplier immediately.

In order to verify that you have received a correct product, please check the model number

printed on the label attached on the rear panel at the lower right corner of the product as shown

below.

AC100-240V 50/60Hz I N

VGA LAN1LAN2 USB3USB4

1234

INPUT

GENLOCKIN

OUTPUT

RS-2

32CREM

OTE

GPI/ALARM

SER

.NO.

MBP-100PD rear panel

Model number label

Table of Contents

1. Prior to Starting ........................................................................................................................ 7

1-1. Welcome ........................................................................................................................... 7

1-2. Features ............................................................................................................................ 7

1-3. Notes on Using The MBP-100PD...................................................................................... 8

2. Panel Descriptions ................................................................................................................... 9

2-1. Front Panel....................................................................................................................... 9

2-2. Rear Panel ...................................................................................................................... 10

2-3. Serial Interfaces .............................................................................................................. 11

2-3-1. REMOTE.................................................................................................................. 11

2-3-2. RS-232C .................................................................................................................. 11

2-4. Parallel Interface ............................................................................................................. 12

3. Connection with Peripherals................................................................................................... 14

3-1. Conversion from HD/SD-SDI to MXF File........................................................................ 14

3-2. Conversion from MXF Files to HD/SD SDI Signals ......................................................... 15

3-3. Genlock Settings ............................................................................................................. 16

4. How to Change Network Settings........................................................................................... 18

4-1. Connecting Monitor, Keyboard, and Mouse .................................................................... 18

4-2. Disabling Write-Protection ............................................................................................... 18

4-3. Changing the Computer Name........................................................................................ 20

4-4. Changing the IP Address................................................................................................. 22

4-5. Enabling Write-Protection................................................................................................ 23

5. Specifications and Dimensions............................................................................................... 24

5-1. Unit Specifications........................................................................................................... 24

5-2. External Dimensions ....................................................................................................... 25

Appendix. How to Reset BIOS ................................................................................................... 26

1. Opening BIOS Setup Menu ................................................................................................ 26

2. Setting Procedure............................................................................................................... 27

1. Prior to Starting

1-1. Welcome

Congratulations! By purchasing MBP-100PD Clip Server (Baseband Converter) you have

entered the world of FOR-A and its many innovative products. Thank you for your patronage and

we hope you will turn to FOR-A products again and again to satisfy your video and audio needs.

FOR-A provides a wide range of products, from basic support units to complex system

controllers, which have been increasingly joined by products for computer video based systems.

Whatever your needs, talk to your FOR-A representative. We will do our best to be of continuing

service to you.

1-2. Features

MBP-100PD is a compact 1RU clip server equipped with HD / SD-SDI inputs and outputs, and a

SSD (Solid State Drive) for data storage. MBP-100PD features recording and playback of

Panasonic P2/P2HD compatible MXF files, and transfer and storage of clips via gigabit Ethernet.

The supported functions such as ingest, playback, and program playout using APC (Automated

Production Control System) are highly versatile and reliable.

Block diagram

Equipped with HD/SD-SDI input and output, and supports conversion between

baseband signals and MXF files (ingest applications)

Even during video recording or playback, clips can be added over the network; no time

lost for switching disks or media (seamless operation)

Supports up to 8 channels of audio in embedded format

Compact 1RU vibration-resistant case; ideal for off-site and in-vehicle applications

Dedicated hardware; unlike products based on computer platforms, the converter can be

easily turned on and off with a single switch

FOR-A’s unique hardware enabls real-time recording and stable playback of video

The vibration-resistant SSD used as storage media enables solid video performance

PCI Express I/F

PCI Express x8

Hrz.

Scaler

Queue

Buffer

Sotware

CODEC

INPUT

Audio

DeMUX

Video

Audio

Hrz.

Scaler

Queue

Buffer

Audio

MUX

Video

Audio

OUTPUT

1-3. Notes on Using The MBP-100PD

Please note the following:

EWF (Enhanced Write Filter) must not be disabled when using the MBP-100PD.

Powering the MBP-100PD on or off while EWF is disabled may corrupt or damage files.

The C drive of the MBP-100PD is write-protected.

Do not create folders or data in the C drive.

Writing in the C drive may cause Windows to hang up.

Files cannot be created on the desktop regardless of whether write-protection is enabled or

disabled.

The below error message will appear if you attempt to write on the desktop.

The MBP-100PD has the Windows Operation System (Microsoft Windows XP Embedded)

installed and customized.

Do not install applications that are not required.

2. Panel Descriptions

2-1. Front Panel

No. Name Description

1 Indicators

POWER Lit green Power is properly supplied to the unit.

Unlit Power is not supplied.

ACT Not in use

FAN

Unlit Cooling fans are properly working.

Lit red One or more fans failed. Power off the unit and

replace the fan which is failed, if necessary.

2 POWER

switch

Power switch. Pressing " I " side turns on the power.

Power indicator will be lit green when the power switch is turned on. It

takes approximately 5 seconds for the indicator to be lit. When turning the

power of the MBP-100PD back on after powering off, wait at least 10

seconds.

3 USB1

USB2 USB ports. (USB2.0 compatible)

4 RESET If the POWER indicator does not light up green in 5 seconds after the

power switch is turned on, press the RESET switch (Not for normal use).

IMPORTANT

If the FAN indicator lights up red, there is a fan failure. Turn off the MBP-100SX and

contact your retailer.

OFF

POWER

RESET

POWERACT FAN

USB 1 USB 2

MBP-100PD

BASEBAND CONVERTER

1 2

2-2. Rear Panel

No. Name Description

1 INPUT 1 For the serial digital component video input (HD/SD SDI). (BNC

connector)

The input selector is internally provided to select which input to record

from input signals in INPUT 1 and 2.

To preview an input video while recording, the input video must be

synchronized with the reference signal input.

2 INPUT 2

3 GENLOCK

For the reference signal input (Black Burst or Tri-level sync signal).

Either connector can be used for the input. The one which is not used

for reference input will be loop through output. The output connector

must be terminated with 75 ohm resistor when it is not used.

4 OUTPUT 1 For the serial digital component video output (HD/SD SDI). (BNC

connector)

OUTPUT 1, 2, 3, and 4 output the same signal.

5 OUTPUT 2

6 OUTPUT 3

7 OUTPUT 4

8 VGA For the output to VGA monitor. (15-pin mini D-sub)

9 LAN1

LAN2

For the connection to the Ethernet port of a computer.

(100BASE-TX/1000BASE-T, RJ-45)

LAN2 is not in use.

10 USB3

USB4

For connecting USB devices such as a keyboard, mouse, and other

USB devices. (USB2.0 compatible)

11 Audio out Audio connector for monitoring audio while previewing video.

Compliant to Intel High Definition Audio, 2ch (Realtek ALC262)

12 GPI /

ALARM

For the power / fan alarm output and the GPI input/output. (15-pin

D-sub female)

13 RS-232C RS232C serial control connection used to controll from a PC.

(9-pin D-sub, male)

14 REMOTE RS422 serial control connection used to control from a PC.

(9-pin D-sub, female)

15 AC IN For the connection to AC power source via supplied AC cord.

(100-240VAC 50/60Hz)

16 Ground

Terminal

For grounding unit to protect operators against static electricity and /

or electrical shock.

17 Cooling Fan

For cooling unit to prevent overheating. Do not block the vent with

other equipment or objects.

AC100-240V 50/60Hz I N

VGA LAN1LAN2 USB3USB4

1234

INPUT

GENLOCKIN

OUTPUT

RS-2

32CREM

OTE

GPI/ALARM

SER

.NO.

12 13 14

4675

15 16 17 1 2 8 9 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere FOR-A Server Handbücher

FOR-A

FOR-A MBP-120SX Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung