formlabs Form 2 Bedienungsanleitung
FormLab 2
November 2017
3D PRINT - FormLab 2
This instruction manual describes the basic operations of the FormLab 2 print.
System consists of :
•Form 2 : Stereolithography SLA
•Build Volume : 145 x 145 x 175mm
•Layer Thickness: 25, 50, 100 microns
•Laser Spot Size: 140 microns
•Laser specifications: 405nm violet laser / 250mW
•Materials: Black, Flexible and Tough Resin
https://formlabs.com/3d-printers/tech-specs/
1
Contents
1 Set Up 3
1.1 Remove the resin cartridge . . . . . . . . . . . . . . . . . . . . . 3
1.2 Remove the Build platform . . . . . . . . . . . . . . . . . . . . . 4
1.3 Remove the resin tank . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Start up 7
2.1 Insert the tank resin . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Insert the build platform . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Insert the resin cartridge . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Print.................................. 10
2.5 Remove the Build platform . . . . . . . . . . . . . . . . . . . . . 12
2.6 Washingyourprint.......................... 13
2.7 Finition ................................ 14
3 Cleaning 15
3.1 Cleaning the optical window . . . . . . . . . . . . . . . . . . . . 15
3.2 Cleaning the tank resin . . . . . . . . . . . . . . . . . . . . . . . 16
4 Level print 17
2
Chapter 1
Set Up
1: Print Cover, 2: Build platform , 3: Resin, 4: Wiper, 5: Resin
Tank, 6: Touchscreen, 7: Sleep / Confirm button, 8: Cartridge Resin.
•Turn on the printer with the Sleep button at the front to the 3D print ( 7).
1.1 Remove the resin cartridge
•Push down the cap 1and 2.
•Remove up the cartridge 3.
3
3D PRINT - FormLab 2 CHAPTER 1. SET UP
1.2 Remove the Build platform
Be careful : Always remove the build platform before removing the
resin tank.
•Put some gloves to remove the build platform.
•Put the handle to up and slide the build platform towards you 2.
•Remove the build platform from the Print 3.
•Turn the platform over to prevent resin dripping 5.
•Clean the build platform with kimtech paper.
4
3D PRINT - FormLab 2 CHAPTER 1. SET UP
1.3 Remove the resin tank
Be careful: Wear gloves each step.
•Pull the wiper towards you and move up the wiper from the wiper mount 2.
•Put the wiper on the right edge of the resin tank 3.
•Cover the resin tank with the black plastic lid 2.
•Remove the resin tank by pulling towards you.
•Put the resin tank into the box 2.
•Put the resin tank into the cabinet.
5
3D PRINT - FormLab 2 CHAPTER 1. SET UP
•Inspect inside the tank 1.
•Check with a spatula all resin surface by beginning from the right-top to the
left-bottom side 2.
•Remove the leftovers materials.
•Close the orange protection cover.
6
Chapter 2
Start up
2.1 Insert the tank resin
•Choose your resin (Black, Resin, Tough...).
•Open the box 1(Be careful when you move the box from cabinet).
•Put some gloves.
1: Cardboard, 2: Resin tank, 3: Resin, 4: Lid
•Remove the tank by handling only the sides 2. Don’t touch the optical
window on the resin tank 1.
7
3D PRINT - FormLab 2 CHAPTER 2. START UP
•Insert the resin tank by aligning the four feet of the resin tank into the four
holes 1.
•Push the tank toward the rear of the 3D print 2.
•Remove the tank lid 4.
•Inspect the resin tank on the bottom side. If you can see some dust or resin,
go to cleaning chapter.
•Put the wiper into the wiper mount 2.
•Push the wiper against the resin tank 3.
8
3D PRINT - FormLab 2 CHAPTER 2. START UP
•Inspect inside the tank 1.
•Check with a spatula all resin surface by beginning from the right-top to the
left-bottom side 2.
•Remove the leftovers materials.
2.2 Insert the build platform
•Insert the build platform 1.
•Lock handle down 2and 3.
9
Andere Handbücher für Form 2
3
Inhaltsverzeichnis
Andere formlabs 3D-Drucker Handbücher
formlabs
formlabs Form Cure Bedienungsanleitung
formlabs
formlabs Fuse Sift Bedienungsanleitung
formlabs
formlabs Form 3 Bedienungsanleitung
formlabs
formlabs Form 2 Bedienungsanleitung
formlabs
formlabs Form Wash Bedienungsanleitung
formlabs
formlabs IBT Flex Resin Bedienungsanleitung
formlabs
formlabs Form Cure Bedienungsanleitung
formlabs
formlabs Form 3BL Bedienungsanleitung
formlabs
formlabs Form Wash L Bedienungsanleitung
formlabs
formlabs FORM 1 Bedienungsanleitung
