Fortinet FortiWLC-500D Bedienungsanleitung
Wireless lan Controller
FortiWLC™-500D
QuickStart Guide
Table of contents
Package contents...................................................... 1
Rack mounting ........................................................ 2
Installing SFP transceivers ............................................. 3
Supported SFP transceivers ............................................ 5
Connecting to FortiWLC ............................................... 6
Shutting down ........................................................ 8
Registering your product .............................................. 9
Ports & LEDs..........................................................10
Replacing a PSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cautions and warnings ...............................................13
Regulatory notices ...................................................15
License agreement & warranty ........................................17
1
2 Power Cables Console Cable
4 Rubber Feet 8 Bracket
Sc rews
Ethernet Cable
2 Rack Mount
Ears
2 Grounding
Sc rews
FortiWLC 500D
QuickStart Guide
Quic kStart Guide
Package contents
The box should contain:
FortiWLC-500D appliance
FortiWLC-500D QuickStart Guide
2 Power cables
Console cable
Ethernet cable
4 Rubber feet
2 Grounding screws
8 Bracket screws
2 Rack mount ears
2
Rack mounting
FortiWLC appliances should be installed in a restricted access location
such as a locked data center to ensure their physical security, which is
fundamental to your network security. Mount the appliance in any standard
19 inch (48.3cm) rack with the rack-mount brackets.
In a rack, a FortiWLC-500D occupies 1U (1.77in/4.45 cm).
• 2-post rack: Attach the rack-mount brackets to the middle of each
side of appliance so that its weight is distributed evenly.
• 4-post rack: Attach the rack-mount brackets to the front of each side
of the appliance with anges facing outwards, towards the notches in
the rack.
3
Installing SFP transceivers
If not already installed, install the SFP/SFP+ transceivers that will be used
to connect your appliance to the network.
Caution: Do not install or remove SFP transceivers while ber-optic cables
are still attached. This can cause damage to the cables, cable connectors,
and optical interfaces. It may also prevent the transceiver from latching
correctly into the socket.
Note: Installing and removing SFP transceivers can shorten their life. Do
not install or remove transceivers more than is necessary.
To install the SFP transceivers
1. On the appliance’s front panel, remove the caps from SFP cage sockets.
2. Position the SFP transceiver in front of the cage socket so that the
extraction lever is level with the socket latch.
Note: SFP cage socket orientation may vary. Ensure that the SFP
transceiver module is correctly oriented.
3. Holding the sides of the SFP transceiver, gently slide it into the cage
socket.
Caution: Do not force SFP transceivers into cage sockets. Force can
cause damage. If the transceiver does not easily slide in and click into
place, it may not be aligned correctly or may be upside down. If this
happens, remove the SFP transceiver, realign or rotate it, and try again.
4
4. Press the transceiver rmly into the cage socket with your thumb until it
clicks, indicating that it is latched.
5. To verify that the transceiver is latched, grasp its sides and try to pull it out
without lowering the extraction lever.
If you can remove the transceiver, it was not latched correctly, and could
become accidentally dislodged. Try again.
To remove the SFP transceivers
1. Disconnect the ber optic cable from the transceiver connector.
2. To prevent dust from entering the optical bores, insert clean plugs.
3. To eject the transceiver, pull the extraction lever out and down.
Tip: Instead of using your nger, try a small at-head screwdriver.
4. Hold the sides of the transceiver and carefully pull it from the cage socket.
5. Replace the cap on the SFP cage socket.
6. Put the removed SFP transceiver into an anti-static bag.
5
Supported SFP transceivers
These are the supported transceivers for FortiWLC-500D.
Supplier Type Part Number
Intel DUAL RATE 1G/10G SFP+ SR (bailed)* FTLX8571D3BCV-IT
Finisar SFP+ SR bailed, 10g single rate* FTLX8571D3BCL
Avago 10GBASE-SR/SW, SFP+ * AFBR-709ASMZ
Finisar DUAL RATE 1G/10G SFP+ * FTLX8571D3BCV
Finisar SFP+ SR, 10g single rate* FTLX 8574D3BCL
HP 1000BASE-SX SFP SFP SX J4858C
Axcen SFP, 1000SX AXGE-5854-0511
Dlink 1GB Copper DGS712
Finisar 1 Gbps SFP FCLF8521P2BTL
NetGear 1 Gbps SFP AGM731F
* Not supported on 1 Gbps SFP module.
6
Connecting to FortiWLC
If the appliance has a redundant power supply, connect each power cable
to a dierent power source.
You can congure FortiWLC for your network through a connection to
command line interface (CLI).
IMPORTANT • FortiWLC-500D is supported ONLY from System
Director 8.0-SR1 and later.
• SFP support is not available in the 8.0-SR1
release.
Connect FortiWLC only to your computer until you nish setup. (If you
place FortiWLC in your network before FortiWLC is set up, trac could
be interrupted until setup is complete.) Detailed instructions are in the
System Director User Guide.
One typical, basic network topology is shown below.
7
To connect to the CLI via serial console
Requires: Terminal emulator such as PuTTY, TeraTerm, or a terminal server
1. Using the console cable, connect the appliance console port to your
terminal server or computer.
2. On your computer or terminal server, start the terminal emulator.
Usethesesettings:
• Baud rate: 115200
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control:None
3. Press Enter on your keyboard to connect to the CLI.
8
Shutting down
Always properly shut down the FortiWLC
appliance’s operating system before unplugging
the appliance. This causes it to nish writing
buered data, and to slow and park the harddisks.
Do not unplug the FortiWLC appliance before
halting the operating system. Failure to shut down
correctly could cause dataloss and hardware
problems.
To power o the appliance via the CLI, use the powero controller CLI
command before unplugging the power.
The command gracefully brings the controller down to a state where power
can safely be removed.
Inhaltsverzeichnis
Andere Fortinet Controller Handbücher
Fortinet
Fortinet FortiADC 1000F Bedienungsanleitung
Fortinet
Fortinet FortiADC 400F Bedienungsanleitung
Fortinet
Fortinet FortiADC 4000D Bedienungsanleitung
Fortinet
Fortinet FortiController-5913C Stücklistenhandbuch
Fortinet
Fortinet FortiController-5103B Bedienungsanleitung
Fortinet
Fortinet FortiADC 4000F Bedienungsanleitung
Fortinet
Fortinet FortiManager 4000E Bedienungsanleitung
Fortinet
Fortinet FortiWLC 1000D Bedienungsanleitung
Fortinet
Fortinet FortiADC 200F Bedienungsanleitung
Fortinet
Fortinet FortiWeb 1000E Bedienungsanleitung
