Fortinet FortiSandbox 1000F Bedienungsanleitung

FortiSandbox 1000F

FSA-1000F & FSA-1000F-DC

QuickStart Guide

Before you begin

firmware upgrades, technical support and warranty coverage.

http://support.fortinet.com

March 16, 2022

of Fortinet, Inc., in the U.S. and other jurisdictions, and other Fortinet names herein may also be registered and/or common law trademarks of Fortinet. All

other product or company names may be trademarks of their respective owners. Performance and other metrics contained herein were attained in internal

lab tests under ideal conditions, and actual performance and other results may vary. Network variables, different network environments and other conditions

may affect performance results. Nothing herein represents any binding commitment by Fortinet, and Fortinet disclaims all warranties, whether express or

implied, except to the extent Fortinet enters a binding written contract, signed by Fortinet’s General Counsel, with a purchaser that expressly warrants that

the identiﬁed product will perform according to certain expressly-identiﬁed performance metrics and, in such event, only the speciﬁc performance metrics

expressly identiﬁed in such binding written contract shall be binding on Fortinet. For absolute clarity, any such warranty will be limited to performance

in the same ideal conditions as in Fortinet’s internal lab tests. In no event does Fortinet make any commitment related to future deliverables, features or

development, and circumstances may change such that any forward-looking statements herein are not accurate. Fortinet disclaims in full any covenants,

representations, and guarantees pursuant hereto, whether express or implied. Fortinet reserves the right to change, modify, transfer, or otherwise revise this

publication without notice, and the most current version of the publication shall be applicable.

For Product License Agreement / EULA and Warranty Terms, visit https://www.fortinet.com/content/dam/fortinet/assets/legal/EULA.pdf

This guide covers: FSA-1000F, FSA-1000F-DC

Box Includes Box Includes

Power Cable

Ethernet Cable

5x Rubber Feet

2x Sliding Rails

2x Sliding Rail Handles

6x M4 Flat Head Screws

2x Rack Mount Screws

10x M4 Wafﬂe Head Screws

Console Cable

FortiSandbox 1000F

4 5

QuickStart Guide

6 7

1 2 3 4

CONSOLE MGMT

POWER

STATUS

HDD

FortiSandbox 1000F

USB

5678 1 2 3 4

CONSOLE MGMT

POWER

STATUS

HDD

FortiSandbox 1000F

USB

5678

Front Panel - Ports

1MGMT (RJ-45) not in use

Console (RJ-45) CLI management computer interface

Ports 1 to 4 (RJ-45) 1 Gbps Ethernet connections

Ports 5 to 8 (SFP) 1 Gbps SFP connections

USB (USB A, B) not in use

FSA-1000F & FSA-1000F-DC

1Green: The device is on

Off: The device is off

Not in use

Red: Device failure

Off: Device is running normally

POWER

STATUS

HDD

ETHERNET

SFP

Ports Link/Activity (Left LED)

Flashing Amber: Data activity

Off: No link established

Ports Speed (Right LED)

Amber: Connected at 1Gbps

Green: Connected at 100Mbps

Off: Connected at 10Mbps or off

Ports Link/Activity (Left LED)

Flashing Amber: Data activity

Off: No link established

Ports Speed (Right LED)

Amber: Connected at 1Gbps

Off: Not in use

FSA-1000F & FSA-1000F-DC

Front Panel - LEDs

8 9

ESD

Rear Panel FSA-1000F Rear Panel FSA-1000F-DC

Reset Switch will reboot the device Reset Switch will reboot the device

Power 100-240V AC, 5-3A, 50/60Hz DC Input (RTN) power supply return

DC Input (Power) -48V DC, 9A

DC Input (GND) power supply ground

ESD

12345

Green: PSU operating normally

Flashing Green: PSU on standby

Flashing Red: No power to the PSU

Red: PSU failure

Off: PSU is off Blue: DC PSU operating normally

Flashing Blue: DC standby on

Flashing Red: No power to the PSU

Red: PSU failure

Flashing Red & Blue: PSU warning

Off: PSU is off

AC Power Supply LED

DC Power Supply LED

RTN

-36V

-72V

RTN

-36V

-72V

10 11

Installation

The FortiSandbox unit can be placed on a ﬂat surface using the provided rubber feet, or

mounted in any standard 19 inch rack unit with the provided mounting rails.

Please also read "Cautions and Warnings" on page <?> prior to installing your device.

Caution: The rack must be stabilized before sliding the unit out for servicing.

Failure to stabilize may cause the rack to tip over.

Electrostatic discharge (ESD) can damage your Fortinet equipment.

To avoid personal injury or damage to the unit, it is recommended that two or more

people install the unit into the rack.

Do not place heavy objects on the unit.

Rack Precautions

• Ensure the leveling jacks on the bottom of the rack are fully extended to the ﬂoor with

the full weight of the rack resting on the jacks.

• For single rack installation, stabilizers should be attached to the rack.

• For multiple rack installations, the racks should be coupled together.

• Ensure the rack is stable before extending a component from the rack.

• Only extend one component at a time; extending two or more simultaneously may

cause the rack to become unstable.

Rack Rail Parts

The rail assembly consists of two parts:

• Outer rail: connects to the rack

• Inner rail: connects to the device

The inner rail has a locking tab that locks the device into place when it is installed and

pushed into the rack. This prevents the device from sliding fully out of the rack when the

device is being worked on.

There are four steps to install the device into the rack:

1. Disassemble the rail assembly

2. Attach the inner rails to the device

3. Install the outer rails on a rack

4. Install the device into the rack

Disassemble the rail assembly

1. Identify the left and right rail assemblies.

2. Pull out the inner rail until it is fully extended.

3. Push the white locking tab to release the inner rail.

4. Remove the inner rail from the outer rail.

5. Repeat steps 2 - 4 for the remaining rail assembly.

Attach the inner rails to the device

1. Ensure that the right and left rails are correctly identiﬁed.

2. Place the inner rail against the side of the device and ensure that the screw holes are

aligned.

3. Secure the rail to the device using ﬁve of the provided M4 Wafﬂe Head screws.

4. Attach the sliding rail handle to the device using three of the provided M4 Flat Head

screws.

5. Repeat steps 2 - 3 for the remaining inner rail.

12 13

Install the outer rails on a rack

1. Ensure that the right and left rails are correctly identiﬁed.

Bracket

Front

Bracket

Rear

2. Press the front of the outer rail into three available screw holes on the front of the

rack until you hear a click.

3. Ensure that the rail is level, then slide the rear of the rail over three holes on the back

of the rack until you hear a click.

No screws are required to secure the rail to the rack.

4. Repeat steps 2 - 3 for the remaining outer rail.

Install the device into the rack

1. Ensure that there is enough room around the unit to allow for sufﬁcient air ﬂow.

2. Ensure that the inner rails are properly connected to the device, and the that the

outer rails are securely attached to the rack.

3. Align the inner rails with the outer rails and slide the device onto the rails until the

locking tabs click into the locked position.

Ensure that even pressure is applied to both sides of the device while doing this.

4. Simultaneously push the locking tabs on both sides while pushing the device all the

way into the rack.

5. For additional security, secure the handles to the front of the rack with the two

provided rack mount screws.

To remove the device from the rack, pull it out as far as it will go, then push the

locking tabs on both sides and slide the device out.

After the device is installed in the rack, plug the provided power cable into the rear of

the unit, and then into a grounded electrical outlet or separate power source, such as an

uninterruptible power supplies (UPS) or a power distribution units (PDU).

To install the unit on a at surface

1. Ensure that the surface onto which the FortiSandbox unit to be installed is clean,

level, and stable, and that there is at least 1.5in (3.8cm) of clearance on all sides to

allow for adequate airﬂow.

2. Attach the provided rubber feet to the bottom of the unit.

3. Place the unit in the designated location.

4. Verify that the spacing around the unit conforms to requirements and that the unit is

level.

1.5in

5. Plug the provided power cable into the rear of the unit, and then into a grounded

electrical outlet or separate power source, such as an uninterruptible power supplies

(UPS) or a power distribution units (PDU).

14 15

Setup Options

Set up your device locally using the GUI or CLI. Choose one of the following

options to complete your setup, then conﬁgure your device.

Local Setup

Command Line Interface (CLI)

An alternate conﬁguration tool from the web-based manager that

uses a terminal emulation application to type commands or upload

batches of commands from a text ﬁle or conﬁguration script.

GUI

Local Setup

An easy-to-use GUI, compatible with most web browsers.

To minimize scrolling, the screen resolution should be at least

1280 x 1024 pixels.

Connect your device as follows:

Port Connection

1Connect a management computer to conﬁgure the device using

the GUI.

Connect to the Internet to access FortiGuard and FortiCare.

2High Availability (HA) connection.

3The VM outgoing port allows possibly malicious connections to

connect to the Internet.

This port should be connected through an isolated network.

4 and up Connect FortiGate or other devices.

Optionally, can be used as sniffer ports.

Connections

Note: The FortiSandbox unit requires some basic conﬁguration to add it to your

network, including assigning IP addresses, DNS settings, and the default gateway.

Until these steps are completed trafﬁc will not ﬂow through the device.

Ethernet port 1 only supports HTTPS, HTTP, SSH, and Telnet services. With the

exception of HTTPS, these services can be disabled using the GUI.

FortiGates (or other

compatible devices)

Management

Computer

Malware

Traffic

FortiGuard

Traffic

1 2 3 4

16 17

Ethernet Cable

1. Connect port 1 to the Management Computer using the suplied Ethernet cable

2. Enable DHCP or set the Management Computer’s IP and subnet to:

Static IP Address: 192.168.1.1

Subnet Mask: 255.255.255.0

3. Visit 192.168.1.99 in a web browser

4. Log in with username admin and no password

5. You can now conﬁgure your FortiSandbox

Management Computer

Port 1

Browse to 192.168.1.99

Username: admin

No Password

GUI

ACLI

1. Connect the Console Port with a console cable to the Management Computer

2. Start a terminal program on the Management Computer and select an available

COM Port using the following default settings:

Baud rate: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

3. Log in using username admin and no password

4. You can now conﬁgure your FortiSanbox

5. See the next page for Useful CLI Commands

Console Port

Serial Port

Console Cable

help Show a list of valid CLI commands.

show Show the bootstrap conﬁguration including

the port IP address (IPv4), network

mask, and default gateway.

set port1-ip <ip>/<netmask> Set the port 1 IP address and netmask.

set portX-ip <ip>/<netmask> Set the port XIP address and netmask.

set default-gw <ip> Set the default gateway.

reboot Reboot the FortiSandbox. All sessions will

be terminated.

shutdown Shut down the FortiSandbox.

status Show various system information.

For example, to conﬁgure the IP address and gateway of the FortiSandbox device, use

the following commands:

set port1-ip 192.168.0.10/24

set default-gw 192.168.0.1

Useful CLI Commands

A limited CLI is available for basic device conﬁguration and debugging purposes.

The FortiSandbox device is primarily conﬁgured using the GUI.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fortinet Firewall Handbücher

Fortinet

Fortinet FortiGate-200A Bedienungsanleitung

Fortinet

Fortinet FortiGate 60M Bedienungsanleitung

Fortinet

Fortinet FortiGate 50A Bedienerhandbuch

Fortinet

Fortinet FortiWeb 1000F Bedienungsanleitung

Fortinet

Fortinet FortiGate FortiGate-800 Bedienerhandbuch

Fortinet

Fortinet FortiGate-400A Bedienungsanleitung

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

Fortinet

Fortinet FortiGate FortiGate-500A Bedienungsanleitung

Fortinet

Fortinet FortiGate 3016B Bedienungsanleitung

Fortinet

Fortinet FortiGate 3000 Bedienungsanleitung

Fortinet

Fortinet FortiMail-4000A Bedienungsanleitung

Fortinet

Fortinet FortiAnalyzer-4000A Bedienungsanleitung

Fortinet

Fortinet FortiMail-2000A Bedienungsanleitung

Fortinet

Fortinet FortiGate FortiGate-50 Bedienerhandbuch

Fortinet

Fortinet FortiMail-400 Bedienungsanleitung

Fortinet

Fortinet FortiAnalyzer-400 Bedienungsanleitung

Fortinet

Fortinet FortiDB-1000B Bedienungsanleitung

Fortinet

Fortinet FortiGate FortiGate-30B Bedienungsanleitung

Fortinet

Fortinet FortiGate-3016B Bedienungsanleitung

Fortinet

Fortinet FortiGate FortiGate-5003 Bedienungsanleitung

Fortinet

Fortinet FortiWeb 100E Bedienungsanleitung

Fortinet

Fortinet FortiGate-50A Bedienungsanleitung

Fortinet

Fortinet FortiWiFi 60D Service-Handbuch

Fortinet

Fortinet FortiGate 5050 Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Cisco

Cisco S190 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Cisco

Cisco 3110 Handbuch

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung

GTA

GTA GB-200 Bedienungsanleitung

Trend Micro

Trend Micro Deep Edge Bedienungsanleitung