Fox F50-800 Bedienungsanleitung

WET & DRY

VACUUM EXTRACTOR

Model F50-800

ASSEMBLY AND OPERATING INSTRUCTIONS

Wet & Dry Vacuum Extractor

FOX MODEL F50-800

TABLE OF CONTENTS

Safety instructions……………………………………………………………………………… Page 3

Specifications…………………………………………………………….……………………... Page 6

Electrical connections……………………………………………………………….…………..Page 7

Environmental protection……………………………………….……………………………… Page 8

Symbols…………………………………………………………………………………….……. Page 8

Package contents…………………………………………………………………………..…... Page 9

Assembly……………………………………………………………………………………..….. Page 10

Switching On/Off …….……………………………………………………………….………… Page 10

Dry vacuuming cleaning………………………………………………………………………...Page 11

Wet vacuuming cleaning….………………………………………………………………..…...Page 12

Blowing…………………………………………………………………………………………… Page 13

Vacuum maintenance…………………………………………………………………………...Page 13

Cartridge filter maintenance…………………………………………………………………….Page 14

Troubleshooting…………………………………………………………………………………. Page 14

Consumables……………………………………………………………………………………. Page 15

DART Tool Group Guarantee………………………………………………………………......Page 16

Declaration of Conformity…………………………………………………………………….... Page 17

ATTENTION :

- Read the instructions for use carefully before using the machine

- This device meets current safety standards for electrical machines.

- Incorrect use may result in injury. Anyone not familiar with the instructions for use should not use the

machine. Keep these instructions for use safe.

SAFETY INSTRUCTIONS

ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOCKET BEFORE ATTEMPTING ANY

MAINTENANCE.

Keep a safe working zone for both staff and equipment. NO CHILDREN must be allowed in the

working zone under any circumstance.

The machine must be always disconnected when not in use. Use the on/off switches on the machine. Always

disconnect the machine by pulling the plug, do not pull the power cord.

Before using the machine, remove all tools used for setup and keep them away from your working zone. Reconnect

the machine. Check that the working zone is clear and that there is plenty room to work with the wood.

Ensure you are in good working position. If the work will produce dust or small pieces, wear safety gear, protective

glasses, gloves, a mask and ear defenders. If you have long hair, tie it up. Do not wear watches or bracelets. Wear

shoes with good grip and remember to never place your fingers too near the blade.

Do not use the machine if you are tired or distracted because you risk injury.

Do not use this machine anywhere containing flammable liquids and/or volatile gases.

1. Keep your working area clean. Untidy working zones and busy workbenches invite injuries.

2. Avoid a dangerous environment. Do not expose machines to rain and not use them in wet places. Ensure your

working zone is well lit. Do not use the machine where there is gas or flammable liquids.

3. Protect yourself from electric shocks. Avoid touching earthed surfaces.

4. Keep children and visitors well away from the working area.

5. Tidy up any tools not in use. When tools are not used, they should be kept in a dry, locked place, out of reach of

children.

6. Do not force the machine. It will work better when used with the pressure it was designed for.

7. Use the correct tools. Do not force a small tool to do the work of a bigger tool. For example, do not use a circular

saw to cut branches or logs.

8. Wear appropriate clothing. Avoid loose clothing, and remove jewellery which could become caught in moving parts.

Non-slip shoes are particularly recommended when working outside. Keep long hair tied up.

9. Always wear safety glasses. Also wear a mask if operating the machine creates dust.

10. Do not mistreat the power cord. Never use the power cord to pull out the plug. Keep the power cord away from

heat, oil and sharp edges.

11. Do not bend over the machine. Keep your balance at all times.

12. Keep tools in good condition. Clean tools to obtain the best results with them. Follow instructions to grease and

change accessories. Regularly check the power cord and replace it if damaged. Keep handles dry, clean and free

from oil and grease.

13. Disconnect the tool when not in use, before the maintenance and while changing accessories such as blades,

drills, etc.

14. Remove all maintenance tools. Get used to checking that all maintenance tools are removed before using the

machine.

15. Avoid accidentally starting the machine. Make sure that the switch is in the "OFF" position before connecting the

power.

16. If the machine is used outside, use only extension leads designed for outdoor use.

17. Be observant. Use common sense when operating machinery. Do not use the tool when tired.

18. Inspect parts before use. Before continuing to use the tool, inspect any protective parts) which could be damaged

to make sure that they work well. Verify that the moving parts are properly aligned, and are not jammed or broken.

Check the assembly and any other conditions which may affect the correct functioning of the machine. Any

damaged part or guard must be repaired or replaced by an approved after-sales service centre. Do not use the

tool if the switch does not work correctly.

19. Warning: the use of any non-recommended accessory can present a health risk.

20. Have the machine repaired by a qualified person. This machine is built according to relevant safety requirements.

Repairs must only be made by a qualified person using original spare parts, otherwise it may be very dangerous

for the user.

21. Keep these instructions.

SPECIFIC SAFETY INSTRUCTIONS FOR VACUUM EXTRACTORS

1. The filtration housing contains a high speed fan blade that can amputate fingers, grab loose clothing and

neckties, and propel dust at high velocities. DO NOT OPERATE WITHOUT ALL PARTS IN PLACE.

2. Do not attempt to clean, remove the filter, or service the unit when the power is on. Turn the unit off and

disconnect the cord from the power source.

3. Static shocks are common in dry areas or when the relative humidity of the air is low. The use of a humidifier

where the dust collector is to be used will help raise the relative humidity, and may reduce static shocks.

4. Sparks inside the electrical parts can ignite flammable vapours or dust.

5. Do not vacuum, or use the vacuum extractor near flammable or combustible liquids, gases, gasoline or other

fuels, lighter fluid, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal dust, magnesium

dust, grain dust, or gun powder.

6. To avoid health hazards from vapours or dusts, do not vacuum toxic materials.

7. Do not use or store near hazardous material.

8. Do not use outdoors or on wet surfaces.

9. Put the unit on a stable, level surface.

10. Position the vacuum hose and electric cord away from traffic areas.

11. Do not allow the unit to be used as a toy. Close attention is necessary when used by or near children.

12. Do not leave the vacuum extractor plugged in. Unplug from the outlet when not in use and before servicing.

13. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

14. Turn off the controls before unplugging.

15. Do not use with a damaged cord, plug, or other parts. If your dust collection system is not working as it should,

has missing parts, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorised

Service Centre.

16. Do not pull or carry by the cord, use the cord as a handle, close the door on the cord, or pull the cord. Keep the

cord away from heated surfaces.

17. Do not handle the plug of the dust collector with wet hands.

18. Do not put any object into the ventilation openings. Do not vacuum with any ventilation opening blocked; keep

free of dust, lint, hair or anything that may reduce air flow.

19. Keep hair, loose clothing, fingers, and all body parts away from openings and moving parts.

20. Extension cords in poor condition or that are too small can cause fire and shock hazards. When using an

extension cord, ensure it is in good condition.

21. Connect to a properly grounded outlet only.

22. Safety is a combination of common sense, staying alert, and knowing how your dust collector works.

23. Keep these instructions safe.

Health Warning

Some dusts created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals

known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

Lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and

chromium from chemically-treated lumber. The risk from these chemicals varies depending on how often you do this

type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment,

such as dust masks that are specifically designed to filter out microscopic particles.

SPECIFICATIONS

Motor : 1400W –240V (1.75hp)

1000W –110V (1.5hp)

Power take-off : 240V / 110V

Power take-off maximum draw : 1400W (240V) / 1000W (110V)

Drum capacity : 30L

Filtration : 0.5 Micron

Flow rate : 60L/sec

Dimensions (h x l x d) : 640x375x470mm

Weight : 9kg

EXTENSION CORDS

Before using an extension cord, ensure the insulation is not cut or worn. Immediately repair or replace a damaged

or frayed cord.

ATTENTION :

Extension cords must be removed from the work area or located so that they will not get caught in parts, tools or other

objects while using the tool.

This appliance must be grounded. If it should malfunction or break down while in use, grounding provides a path of

least resistance for the electrical current and reduces the risk of electrical shock to the operator. This appliance has

a power cord with equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate

outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a

qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the machine. If it will not fit the outlet, have a proper outlet installed by a qualified

electrician.

ELECTRICAL CONNECTIONS

ENVIRONMENTAL PROTECTION

INFORMATION FOR USERS

In accordance with art. 13 of Legislative Decree 25th July 2005, no. 151 “Implementation of

Directives 2002/95/EEC, 2002/96/EEC and 2003/108/EEC, relative to reducing the use of

hazardous substances in electric and electronic appliances and the disposal of waste”, please

take note of the following:

The crossed out wheelie bin symbol found on the appliance or the packaging indicates that

the product must be disposed separately from ordinary household waste when it reaches

the end of its working life.

The user must consign the unwanted appliance to an authorised waste disposal centre for

electric and electronic goods, or alternatively, hand it over to the relative dealer at the

moment of purchasing a new appliance of the same type on a basis of a one to one ratio.

Differentiated disposal to enable possible recycling or environmentally compatible

elimination of the appliance, helps to limit undesirable effects on health and environment

and promotes the reuse and/or recycling of the materials that compose the appliance.

WARNING!

In accordance with the relative legislation in force in the country of use, sanctions will be

imposed on the user if the appliance is disposed of illegally.

SYMBOLS

Read the instruction manual carefully

Use personal protection devices

(goggles, dust mask, earphones)

Serial number / year of production

Unpack your vacuum extractor carefully, taking care with the loose parts.

Note : if any parts are damaged or missing, do not connect the machine to the power and do not

switch it on until the missing/damaged parts are replaced.

Do not throw away the cardboard box until you are sure the machine is working correctly.

Locate the two side clasps which hold the top section in place (Fig. 2)

Undo the clasps, remove the top section and take out the items in the

container.

Check and identify each component listed below. If anything is missing or

damaged, please contact your supplier immediately.

Parts Description

1. Handle

2. Top section

3. Blow connection

4. Filter basket

5. Hose set

6. Crevice tool

7. Rubber adaptor

8. Stainless steel tube

9. Floor nozzle

10.Dust bag

11.Safety float valve

12.Function switch

13.Air regulator handle

14.Cartridge filter

15.Drain outlet

16.Foam filter

17.Socket

18.On/Off switch

19.Clasp x 2

20.Vacuum hose connection

21.Container

22.Castors x 4

PACKAGE CONTENTS

1. Ensure the mains plug is disconnected (Fig. 1)

2. Undo the clasps (Fig. 2)

3. Lift off the top section assembly (Fig. 3)

4. Remove the contents from inside the container (Fig.

5. Turn the container upside down and insert the four

feet with castor wheels at the rear of the tank.

Ensure they are mounted correctly and pushed all

the way in. Screw in until tight (Fig. 5)

6. For wet vaccum cleaning, fit the supplied foam filter

(Fig. 6a)

7. For dry vacuum cleaning, fit the supplied cartridge

filter (Fig. 6b)

8. Or for dry vacuum cleaning, fit the optional dust bag

(Fig. 6c)

9. Replace the top section onto the container (Fig. 7)

10.Align the top section with the clasps and snap into

place, by applying pressure at the mid-point of the

clasps (Fig. 8)

11.Insert the large end of the hose into the front inlet of

the container and screw it in until tight (Fig. 9)

12.Choose the desired nozzle/extension tube(s) and

push it onto the suction tube (Fig. 10)

13.Store accessories as shown by inserting the accessory into the storage slot after use (Fig.

11)

A: Function switch

B: Outlet socket

C: On/Off switch

1. Connect the mains plug

2. To switch on the vacuum cleaner, press or

3. Switch on the electrical appliance. Only connect electrical appliances with a maximum power

rating of 1200W (240V) / 1000W (110V)

4. Switching on the electrical appliance automatically switches on the vacuum cleaner.

5. Once the electrical appliance has been switched off, the vacuum cleaner switches off

following a time lapse

6. To switch off the vacuum cleaner, press

ASSEMBLY

SWITCHING ON/OFF

Inhaltsverzeichnis

Andere Fox Schrubber Handbücher

Fox

Fox F50-843 Bedienungsanleitung

Beliebte Schrubber Handbücher anderer Marken

Olympus

Olympus M200H Bedienungsanleitung

Clarke

Clarke BEXT 100H Installations- und Betriebsanleitung

JOHNY VAC

JOHNY VAC JVC70BCT Bedienungsanleitung

RCm

RCm Elan Series Handbuch

Kärcher

Kärcher B 120 W Bedienungsanleitung

Truvox

Truvox Orbis MotorScrubber 20 Bedienungsanleitung

Numatic

Numatic TTB 4045/100 Bedienungsanleitung

U.S. Products

U.S. Products PEX 500-C-TICK Betriebsanleitung

Mclennan

Mclennan C510 Bedienungsanleitung

Tennant

Tennant T20 LPG Bedienungsanleitung

Columbus

Columbus ARA 66 BM 100 Bedienungsanleitung

Numatic

Numatic TTV 678G / 300T Bedienungsanleitung

American-Lincoln

American-Lincoln 505-945 Bedienungsanleitung

FIORENTINI

FIORENTINI ET 65-75 Bedienungsanleitung

Floorpul

Floorpul ruby 48 blt Benutzerhandbuch

Onyx

Onyx RX-34 Bedienungsanleitung

Dustbane

Dustbane Hurricane 400 Bedienungsanleitung

Sana

Sana EUJ-702 Bedienungsanleitung