Foxconn 845GVME-S Datenblatt

845GVME-S

P/N: 91-185-U45-F1-0E

Motherboard Layout

Easy Installation Guide

Remark:

The above motherboard layout is provided for reference only;

please refer to the physical motherboard.

JP4USBPowerSelec-

tionJumper

ATA33/66/

100IDE

Connectors

CD_INAudioConnector

12VATXPowerConnector

ATXPowerConnector

184-pin DIMM Slots

North Bridge: Intel®

845GVChipset

SouthBridge:Intel®

ICH4 Chipset

ClearCMOSJumper

FDD

Connector

FrontAudioConnector

IRConnector

SystemFANConnector

478-pinCPUSocket

PCIExpansionSlots

USB2.0Connector

FrontPanelConnector

BIOS-Protection

Jumper

CPUModelSelection Jumper

COM2Connector

CPU FAN Connector

JP3USBPowerSelec-

tionJumper

JP5USBPowerSelec-

tionJumper

PS/2 Mouse Connector

This green 6-pin connector is for a PS/2 mouse.

PS/2 Keyboard Connector

This purple 6-pin connector is for a PS/2 keyboard.

Serial Port (COM1)

This 9-pin COM1 port is for a serial mouse or other serial devices.

SPP/EPP/ECP Parallel Port (Printer Port)

This 25-pin port is for a parallel printer, a scanner, or other devices.

VGA Connector

The VGA connector is for output to a VGA-compatible device.

USB 2.0 Ports

These four Universal Serial Bus (USB) ports are available for connecting USB

2.0 devices.

LAN Connector

This port is for connection to a Local Area Network (LAN) through a network hub.

Line-in jack, Line-out jack, Microphone jack

When using a two-channel sound source, the Line-out jack is used to connect to

speakers or headphones; the Line-in port connects to an external CD player,

tape player or other audio device. The Microphone jack is used to connect to the

microphone.

Rear Panel

Serial Port

(COM1)

PS/2Mouse

Connector

SPP/EPP/ECP

Parallel Port

(Printer Port)

10Mb/100Mb

LANConnector

Line-in jack

Line-out jack

Microphone

jack

PS/2 Keyboard

Connector

VGA

Connector USB2.0 Port

845GVME-S Motherboard (x1)

Foxconn Utility CD (x1)

Easy Installation Guide (x1)

IDE Ribbon Cable (x1)

FDD Ribbon Cable (x1)

I/O Shield (x1)

Accessory Checklist

CPU/Memory Support Features

CPU:

Supports Intel®Pentium®4 socket 478 (Willamette/Northwood/Prescott)

processors

Supports Intel®Celeron®socket 478 (Willamette/Northwood/Prescott) pro-

cessors

Supports FSB at 400MHz/533MHz

Supports up to 2.8G Prescott CPU and 3.06G Northwood CPU

Memory:

Supports two 184-pin DIMM slots

Supports DDR266/333

Supports memory technology up to 2GB

The default status for JP2 is Open, which supports the

Prescott and Northwood CPU. If JP2 set as Close, then

it supports the Willamette CPU.

3. CPU Selection Jumper: JP2

The motherboard BIOS is inside the FWH. If the jumper

BIOS_WP set as Close, the system BIOS is protected

from being attacked by a serious virus, such as the

CIH virus. You will be unable to flash the BIOS to the

motherboard when the system BIOS is protected.

2. BIOS-Protection Jumper: BIOS_WP

This motherboard uses the CMOS RAM to store all

the parameters. The CMOS can be cleared by reset-

ting the CMOS jumper. You can refer to the following

process.

1. Turn off the AC power supply and connect pin 1 and

2 together using the jumper cap.

2. Return the jumper setting to normal (pin 2 and 3

together with the jumper cap).

3. Turn the AC power supply back on.

Clear

CMOS

Normal Status

(Default)

1. Clear CMOS Jumper: CLR_CMOS

CLR_CMOS

Open

Disabled Protection

BIOS_WP

Enabled Protection

(Default)

Attach the power LED, IDE LED, reset switch and

power switch connectors to the corresponding pins.

4. Front Panel Connector: FP1

Open

(Default)

JP2

HD-LED PWRLED

PWRSW

EMPTY

RESET

FP1

The motherboard uses JP3, JP4, JP5

jumper to select USB power. JP3 is for

USB, JP4 is for NIC_USB, JP5 is for Front

USB (FP_USB1). Pin 1 and 2 together

(default) select +5V_SYS power, which

doesn’t supports USB device wake up

function. Pin 2 and 3 together select

+5V_SB, which supports USB device wake

up function.

5. USB Power Selection Jumper: JP3, JP4, JP5

+5V_SYS

(Default)

+5V_SB

JP4

JP3

+5V_SB

+5V_SYS

(Default)

JP5

+5V_SB

+5V_SYS

(Default)

NIC_USB

USB

FP_USB1

for

The fan speed of PWR_FAN and CPU_FAN can be

detected and viewed in ‘‘PC Health Status’’ section

of the CMOS Setup. These fans will be automatically

turned off after the system enters S4 and S5 mode.

6. Fan Connectors: PWR_FAN, CPU_FAN

Besides four USB ports on the rear panel, the se-

ries of motherboard also have one 10-pin header

on board which may connect to front panel USB

cable (optional) to provide two additional USB ports.

7. USB 2.0 Header: FP_USB1

FAN1

+12V

SENSE

GND

CPU_FAN

+12V

SENSE

GND

D1-

VCC

GND

D1+

FP_USB1

D0+

Empty

GND

VCC

1 2

9 10

D0-

The audio interface provides two kinds of audio

output choices: the Front Audio, the Rear Audio.

Their priority is sequential from high to low(Front

Audio to RearAudio). If headphones are plugged

into the front panel of the chassis(using the

Front Audio), then the Line-out (the Rear Audio)

on the rear panel will not work. If you do not

want to use the Front Audio, pin 5 and pin 6, pin

9 and pin 10 must be SHORT, and then the

signal will be sent to the rear audio port.

9. Front Audio Connector: F_AUDIO1

The connector supports wireless transmitting and

receiving device. Before using this function, config-

ure the settings of IR Mode from the “Integrated

Peripherals” section of the CMOS Setup.

10. IrDA Header: IrDA

AUD_OUT_L

CD_IN is Sony standard CD audio connector, it can be

connected to a CD-ROM drive through a CD audio

cable.

8. CD_IN Connector: CD_IN

CD_IN

CD_R

CD_L

GND

IrDA

+5V

GND

IRRX IRTX

Empty

MIC_IN MIC_GND

+5VA

AUD_OUT_R AUD_RET_R

NC Empty

AUD_RET_L

F_AUDIO1

910

MIC_PWR

This motherboard attached a serial connector for your

computer, you only need connect it with cable, then link

devices to cable port.

11. COM2 Connector: FP_COM2

12. 6-channel Audio Effects

The motherboard is equipped with the Realtek ALC655 chip, which provides sup-

port for 6-channel audio output, including 2 front, 2 rear, 1 center and 1 subwoofer

channel. ALC655 allows the board to attach 2, 4 or 6 speakers for a better sur-

round sound effect. To apply this function, you have to install the audio driver in

utility CD as well as an audio application supporting 6-channel. Picture below

represents the standard location of all speakers in 6-channel sound track. Con-

nect the front speaker to the green audio output; connect the surround sound

speaker to the blue audio input; connect the center speaker/subwoofer to the red

Microphone input.

FP_COM2

SOUT RTS

RLSD

CTS

GND

DSR Empty

DTR

SIN

Front

Left Front

Right

Rear Left Rear Right

Center

Blue

Green

Red

Subwoofer

14. Foxconn Utility CD

This motherboard comes with one Utility CD. To begin using the CD, simply insert

the CD into your CD-ROM drive. The CD will automatically display the main menu

screen. After selecting Install Driver, you can install its Chipset Software, IAA,

DirectX 9.0, VGA Driver, USB 2.0 Driver, Audio Driver, LAN Driver from this CD.

Follow the screen

order to install the

motherboard

drivers.

After you finish the setting of jumpers and connect correct cables. Power on and

enter the BIOS Setup, Press <Del> during POST (Power On Self Test). Choose

“Load Optimized Defaults” for recommended optimal performance. Please en-

sure your system components are good enough for optimized defaults.

13. Power on and Load Optimized Defaults

Select this option

and press <Enter>.

Inhaltsverzeichnis

Andere Foxconn Hauptplatine Handbücher

Foxconn

Foxconn G43MX Series Bedienungsanleitung

Foxconn

Foxconn A74GA Series Bedienungsanleitung

Foxconn

Foxconn H67S Series Bedienungsanleitung

Foxconn

Foxconn H61MXP Series Bedienungsanleitung

Foxconn

Foxconn H77MXV Series Bedienungsanleitung

Foxconn

Foxconn 45CTD Original Betriebsanleitung

Foxconn

Foxconn 661FX7MJ Series Bedienungsanleitung

Foxconn

Foxconn M61PMX series Bedienungsanleitung

Foxconn

Foxconn P4M8907SA Bedienungsanleitung

Foxconn

Foxconn H81MX Series Bedienungsanleitung

Foxconn

Foxconn H61MXE Series Bedienungsanleitung

Foxconn

Foxconn FlamingBlade GTI Bedienungsanleitung

Foxconn

Foxconn D51S series Bedienungsanleitung

Foxconn

Foxconn 6100M2MA series Bedienungsanleitung

Foxconn

Foxconn G31AX-K Bedienungsanleitung

Foxconn

Foxconn A74ML-K 3.0 Bedienungsanleitung

Foxconn

Foxconn H77M Series Bedienungsanleitung

Foxconn

Foxconn A88GM Deluxe Bedienungsanleitung

Foxconn

Foxconn MCP61PM2MA Bedienungsanleitung

Foxconn

Foxconn G31 MX series Bedienungsanleitung

Foxconn

Foxconn 845GV4MR-ES Datenblatt

Foxconn

Foxconn A76GMV Bedienungsanleitung

Foxconn

Foxconn Renaissance II Bedienungsanleitung

Foxconn

Foxconn P35AP-S Series Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung