Foxfury Lighting Solutions Taker B70 Bedienungsanleitung

PRODUCT MANUAL

480-600

TAKER B70

TABLE OF CONTENTS

INTRODUCTION

Taker B70 Reference Guide 3

Physical Characteristics & Warnings 4

BATTERY

Battery Installation and Replacement 5

Battery Life 6

OPERATION

Operational Modes 6

FEATURES

Ambidextrous Light Activation 7

Pressure Switch 7

Individual LED Rows 8

Dual Settings 8

INSTALLATION

Shield Installation 9

Wiring Installation 10-11

WARRANTY 12–13

CONTACT FOXFURY 13

TAKER B70 REFERENCE GUIDE

SHIELD LIGHT

(WITH PROTECTIVE COVER ON)

SHIELD LIGHT

(WITH PROTECTIVE COVER OFF)

+ +

– –

+ +

– –

HANDLE

(BACK SIDE)

PROTECTIVE

COVER

LEDs (6)

PROTECTIVE

LENS (2)

WIRE

HOLES

(4)

TERMINAL

BLOCKS (4)

POWER/MODE

SWITCH (2)

BOLT HOLE (2)

BATTERY

DOOR (2) GRIP

SCREWS (10)

BOLT

HOLE (2)

WIRE

THROUGH

HOLES (4)

PHYSICAL CHARACTERISTICS

Please read below before using the Taker B70 as it relays beneficial operating

and safety information.

SHIELD LIGHT (P/N 600-480-300)

DIMENSIONS (WxH) 6.3 x 2.5 in (160 x 2.5 mm)

WEIGHT 35.2 oz (998 g)

HANDLE ONLY (P/N 60-601)

DIMENSIONS (WxH) 5.5 x 4.3 in (127 x 109 mm)

WEIGHT 19.2 oz (554 g) with batteries

WARNINGS

Do not stare into LEDs for long periods of time or from a close range

(less than 2 ft (.06 m)).

FoxFury’s Turbo-Strobe™is purposely designed to induce disorientation.

Prolonged viewing may produce vertigo or even vomiting.

Do NOT attempt to charge the batteries by using the Pressure Switch

Port.

INCLUDED

Handle with Electronics & Pressure Switch (P/N 60-601)

Dual Discover Shield Light Head (P/N 600-480-600)

BATTERY INSTALLATION AND REPLACEMENT

1. Twist the Battery Door (at both ends of the handle) in a counter-clockwise

direction to remove them.

2. Insert three (3) batteries (with the negative end first) into either side of the

handle (respect appropriate polarity when installing).

If installing six (6) batteries (doubling battery life), then repeat step 2

one more time on the opposite side of the handle.

3. Re-install the End Cap(s) by twisting in a clockwise direction (make sure

the End Cap(s) are tightly sealed).

Test the light’s performance and function by activating the Power/

Mode Switch (located under the Grip).

BATTERIES

The Taker B70 uses three (3) or six (6) CR123 batteries. As long as there

are at least three (3) installed, the light will function.

Using three (3) CR123 batteries decreases the battery life by half, but

does not effect the light intensity.

Mixing of new and used, or different brand batteries is not recommended

as this could lead to leakage or explosion.

+–

OPERATIONAL MODES

BATTERY LIFE

MODE BATTERY LIFE LUMENS

MOMENTARY 2 hours 1200

CONTINUOUS ON 2 hours 1200

TURBO-STROBE™ 4 hours 1200

*Battery life may vary according to mode selected, battery quality and prevailing ambient conditions.

For MOMENTARY mode: Press and hold the Power/Mode Switch. While

the Switch is depressed, the light will operate continuously. When the user

removes pressure from the Switch, the light will turn OFF.

For CONTINUOUS ON mode: Press the Power/Mode Switch two (2)

times in rapid succession. The light will remain ON.

For TURBO-STROBE™: Press the Power/Mode Switch three (3) times in

rapid succession.

For OFF or EXIT a mode: Press the Power/Mode Switch once. Then,

continue following the directions above to progress to desired mode.

NOTE: The light does not retain the mode in memory. Once you turn the light

ON, you will have to re-select the mode you desire.

FEATURES

AMBIDEXTROUS LIGHT ACTIVATION

The Taker B70 includes two (2) Power/Mode Switches on both the left and

right sides of the Handle. This allows users to toggle between modes using

either hand.

PRESSURE SWITCH (INCLUDED)

The Taker B70 includes a Pressure Switch that allows the user to place

it anywhere on the shield. This makes it easier to access the Power/Mode

Switch. The Pressure Switch can easily be attached to the shield or Handle via

Velcro®or glue.

POWER/MODE

SWITCH

POWER/MODE

SWITCH

PRESSURE

SWITCH PORT

PRESSURE SWITCH

HANDLE

(BACK SIDE)

HANDLE

(FRONT SIDE)

FEATURES (CONT’D)

INDIVIDUAL LED ROWS

The LEDs of the B70 operate on separate circuits, allowing a single row of

LEDs to continue functioning if the other row is damaged.

DUAL SETTINGS

The Taker B70 includes two mode settings: the ON/OFF SETTING and the

TACTICAL SETTING. The ON/OFF SETTING simply allows the Light Head to

turn ON and OFF. The TACTICAL SETTING allows you to choose from three

(3) different Operational Modes: Momentary, Continuous On, and

Turbo-Strobe™. The Taker B70 is shipped in the TACTICAL SETTING.

To change from the TACTICAL SETTING to the ON/OFF SETTING:

With the light turned OFF, press the Power/Mode Switch twice in rapid

succession and hold for 10 seconds. The light should begin to flash. Once

it begins flashing, it is now in the ON/OFF SETTING.

To change from the ON/OFF SETTING to the TACTICAL SETTING:

With the light turned OFF, press and hold the Power/Mode Switch for 10

seconds. The light should begin to go through a slow Turbo-Strobe™ cycle

and then turn OFF. It is now in the TACTICAL SETTING.

SHIELD INSTALLATION

1. Begin by drilling two holes into the shield. To do this, locate the Bolt Hole(s)

(2) located on the BACK SIDE of the Handle (shown above).

HELPFUL TIP: Use a #2 pencil (or a tool of the same diameter) and

insert it through the Bolt Holes (of the BACK SIDE of the Handle)

to draw two marks on the shield. This will help when determining

placement of the holes when drilling.

IMPORTANT: The bolts pictured above are NOT included. The user must

purchase two (2) bolts with the following specifications:

Bolt Head Diameter: 24 mm MAXIMUM

Bolt Shaft Diameter: 7.5 mm MAXIMUM

Bolt Length: 97 mm (this does NOT include the thickness of the shield)

2. Once both holes are drilled through the shield, it is important to drill two

small holes (4 mm diameter) next to each Bolt Hole, so that the wires can

be fed through the shield. NOTE: See pg. 10–11 for wiring installation.

PROTECTIVE COVER

BOLTS (2)

(NOT INCLUDED)

BOLT

HOLES

BALLISTIC SHIELD

Place the shield in

between the Handle

and Light Head.

(The shield pictured is cut in

half for this visual)

LIGHT HEAD

HANDLE

(BACK SIDE)

The B70 is intended to be installed as an OEM product, by ballistic shield and

armor manufacturers.

+ +

– –

+ +

– –

WIRING INSTALLATION

1 2

TERMINAL BLOCK SCREWS

WIRE

THROUGH

HOLES (4)

TERMINAL

BLOCK

HOLDER

SCREWS

(10)

RED WIRE

HOLE

BLACK WIRE

HOLE

Andere Handbücher für Taker B70

Inhaltsverzeichnis

Andere Foxfury Lighting Solutions Taschenlampe Handbücher

Foxfury Lighting Solutions

Foxfury Lighting Solutions Breakthrough series Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions TAKER R40 Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions TAKER B30 Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions TAKER B50 Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions Taker B10 Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions SCOUT J SERIES Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions 920-310 Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions BREAKTHROUGH BT2 Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions Scout Tac Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions 380-BTS-BL Bedienungsanleitung

Foxfury Lighting Solutions

Foxfury Lighting Solutions HAMMERHEAD SERIES Bedienungsanleitung

Beliebte Taschenlampe Handbücher anderer Marken

StreamLight

StreamLight PROPOLYMER 2AA Bedienungsanleitung

StreamLight

StreamLight Stinger Bedienungsanleitung

Silverline

Silverline 994024 Bedienungsanleitung

Gama Sonic

Gama Sonic 23i60065 Bedienungsanleitung

Olympia

Olympia RG580 CREE XM-L2 Bedienungsanleitung

EUFAB

EUFAB 13495 Bedienungsanleitung

OLIGHT

OLIGHT S35 BATON Bedienungsanleitung

Kopp

Kopp Emergency Sensor Light Bedienungsanleitung

YLP

YLP PROFESSIONAL Series Bedienungsanleitung

Light motion

Light motion GoBe Bedienungsanleitung

MOB

MOB MO8622 Bedienungsanleitung

EuroLite

EuroLite KKS-3 Bedienungsanleitung

Carson

Carson 500907010 Bedienungsanleitung

Duracell

Duracell 550 Bedienungsanleitung

Mactronic

Mactronic Black Eye 1300 Bedienungsanleitung

Eurotops

Eurotops 29780 Bedienungsanleitung

MOB

MOB MO8690 Bedienungsanleitung

Pelican

Pelican L1 1930 LED Bedienungsanleitung