Franke FCR 925 TC Bedienungsanleitung

Instructions for use and installation

Cooker Hood

Istruzioni per l’uso e l’installazione

Cappa

Mode d’emploi et installation

Hotte de Cuisine

Bedienungsanleitung und Installation

Dunstabzugshaube

FCR 925 TC BK/XS CH

INDEX

SAFETY INFORMATION 3

CHARACTERISTICS 6

INSTALLATION 7

USE 10

MAINTENANCE 11

INDICE

INFORMAZIONI SULLA SICUREZZA 12

CARATTERISTICHE 15

INSTALLAZIONE 16

USO 19

MANUTENZIONE 20

SOMMAIRE

CONSIGNES DE SÉCURITÉ 21

CARACTERISTIQUES 24

INSTALLATION 25

UTILISATION 28

ENTRETIEN 29

IN ALTSVERZEIC NIS

SICHERHEITSINFORMATIONEN 30

CHARAKTERISTIKEN 33

MONTAGE 34

BEDIENUNG 37

WARTUNG 38

SAFETY INFORMATION

For your safety and correct operation of the appliance, read this manual

carefully before installation and use Always keep these instructions

with the appliance even if you move or sell it Users must fully know the

operation and safety features of the appliance

The wire connection has to be done by specialized technician

•The manufacturer will not be held liable for any damages resulting from

incorrect or improper installation

•The minimum safety distance between the cooker top and the extractor

hood is 650 mm (some models can be installed at a lower height,

please refer to the paragraphs on working dimensions and installation)

•If the instructions for installation for the gas hob specify a greater

distance, this must be respected

•Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood

•Means for disconnection must be incorporated in the fixed wiring in

accordance with the wiring rules

•For Class I appliances, check that the domestic power supply

guarantees adequate earthing

•Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm The route of the flue must be as short as possible

•Regulations concerning the discharge of air have to be fulfilled

•Do not connect the extractor hood to exhaust ducts carrying

combustion fumes (boilers, fireplaces, etc )

•

If the extractor is used in conjunction with non-electrical appliances

(e g gas burning appliances), a sufficient degree of aeration must be

guaranteed in the room in order to prevent the backflow of exhaust gas

When the cooker hood is used in conjunction with appliances supplied

with energy other than electric, the negative pressure in the room must

not exceed 0,04 mbar to prevent fumes being drawn back into the room

by the cooker hood

•The air must not be discharged into a flue that is used for exhausting

fumes from appliances burning gas or other fuels

•If the supply cord is damaged, it must be replaced from the manufac-

turer or its service agent

•Connect the plug to a socket complying with current regulations, locat-

ed in an accessible place

•With regards to the technical and safety measures to be adopted for

fume discharging it is important to closely follow the regulations provid-

ed by the local authorities

WARNING: Before installing the Hood, remove the protective films

•Use only screws and small parts in support of the hood

WARNING: Failure to install the screws or fixing device in accordance

with these instructions may result in electrical hazards

•Do not look directly at the light through optical devices (binoculars,

magnifying glasses…)

•Do not flambè under the range hood; risk of fire

•This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and under-

stand the hazards involved Children shall not play with the appliance

Cleaning and user maintenance shall not be made by children without

supervision

•Children should be supervised to ensure that they do not play with the

appliance

•

The appliance is not to be used by persons (including children) with re-

duced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

Accessible parts may become hot when used with cooking appliances

•Clean and/or replace the Filters after the specified time period (Fire

hazard) See paragraph Care and Cleaning

•There shall be adequate ventilation of the room when the range hood is

used at the same time as appliances burning gas or other fuels (not

applicable to appliances that only discharge the air back into the room)

•The symbol

on the product or on its packaging indicates that this

product may not be treated as household waste Instead it shall be

handed over to the applicable collection point for the recycling of elec-

trical and electronic equipment By ensuring this product is disposed of

correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by

inappropriate waste handling of this product For more detailed infor-

mation about recycling of this product, please contact your local city of-

fice, your household waste disposal service or the shop where you pur-

chased the product

C ARACTERISTICS

Dimensions

11b

Components

Ref. Q.ty Product Components

1 1 Hood Body, complete with: Controls, Light, Blower,

Filters

2 1 elescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

9 1 Reducer Flange ø 150-120 mm

11b 2 Flap

15 1 Air Outlet Connection

Ref. Q.ty Installation Components

7.2.1 2 Upper Chimney Section Fixing Brackets

11 6 Wall Plugs

12a 6 Screws 4,2 x 44,4

12c 6 Screws 2,9 x 6,5

Q.ty Documentation

1 Instruction Manual

INSTALLATION

Wall drilling and bracket fixing

Wall marking:

• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the

centre of the area in which the hood will be installed.

• Draw a horizontal line at 650 mm above the hob. Place bracket 7.2.1 on the wall as shown

about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical

reference line.

• Mark the wall at the centres of the holes in the bracket.

• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the

upper

chimney section supplied), aligning the centre (notch) with the vertical line.

• Mark the wall at the centres of the holes in the bracket.

• Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm

above the horizontal reference line.

• Repeat this operation on the other side.

• Drill ø 8 mm holes at all the centre points marked.

• Insert the wall plugs 11 in the holes.

• Fix the brackets using the 12a (4,2 x 44,4) screws supplied.

• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap

of 5-6 mm between the wall and the head of the screw.

12a

320 X

116

1÷2

116

650 min.

7.2.1

Mounting the hood body

• Before attaching the hood body, tighten the two screws Vr located on

the hood body mounting points.

• Hook the hood body onto the screws 12a.

• Fully tighten support screws 12a.

• Adjust screws Vr to level the hood body.

• If necessary, it is possible to fasten the hood to the wall using more

screws with wall plugs, which can be positioned from inside the hood

canopy.

12a

Connections

AIR OUTLET DUCTING VERSION

When installing the Ducting version, join the Hood to the outlet

duct using a rigid or flexible pipe ø150 or 120 mm, selection of

which is at the discretion of the installation technician.

• Insert flaps 11b on the Hood Canopy Outlet.

Connecting the ø 150 pipe

• Fasten the pipe using suitable pipe clamps. The materials re-

quired to do so are not provided.

Connecting the ø 120 pipe

• To connect using a ø120 mm pipe, insert the reduction Flange

9onto the Hood Canopy Outlet.

• Fasten the pipe using suitable pipe clamps. The materials re-

quired to do so are not provided.

• In both cases, any Activated Charcoal Filters must be removed.

ø 120ø 150

AIR OUTLET – RECIRCULATION VERSION

• Unfasten the 2 screws fixing the upper bracket 7.2.1.

• Fasten the air outlet connector 15 in its place, using the 2

screws removed as above.

• Join the Connector 15 to the Hood canopy outlet using a rigid

or flexible pipe ø150 mm, selection of which is at the

discretion of the installation technician.

• Make sure that the Activated charcoal odour filter has been

fitted.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch hav-

ing a contact gap of at least 3 mm.

• Remove the grease filters (see paragraph Maintenance) being

sure that the connector of the feeding cable is correctly inserted

in the socket placed on the side of the fan.

Flue assembly

Upper exhaust flue

• Slightly widen the two sides of the upper flue and hook them

behind the brackets 7.2.1, making sure that they are well seat-

ed.

• Secure the sides to the brackets by using the 4 screws 12c (2,9

x 9,5) supplied.

• Make sure that the outlet of the extensions pieces is aligned

with the chimney outlets.

Lower exhaust flue

• Slightly widen the two sides of the flue and hook them be-

tween the upper flue and the wall, making sure that they are

well seated.

• Fix the lower part laterally to the hood body by using the 2

screws 12c (2,9 x 9,5) supplied.

12b

USE

Control panel

T1 T2 T3 T4 L

Button Function

T1 Turns the Motor off.

T2 Turns the motor on at speed one Buttons T1+T2 are lit.

T3 Turns the Motor on at speed two Buttons T1+T3 are lit.

Press and hold for 2 seconds to activate

switch-off with a 30 minute delay (Mo-

tor+Lights). It is possible to change the oper-

ating speed with this function activated.

Buttons T1+ (T2 or T3 or

T4, respectively) flash.

T4 Turns the Motor on at speed three Buttons T1+T4 are lit.

Press and hold for 2 seconds to activate In-

tensive speed with a timer set to 6 minutes,

after which it returns to the speed that was

set previously. Suitable to deal with maxi-

mum levels of cooking fumes.

The Button flashes.

L Turns the Lighting system on and off at max-

imum intensity.

Button on

Andere Handbücher für FCR 925 TC

Inhaltsverzeichnis

Sprachen:

Andere Franke Dunstabzugshaube Handbücher

Franke

Franke FTU PLUS 3707 I BK Bedienungsanleitung

Franke

Franke FSMO 805 Bedienungsanleitung

Franke

Franke FMA PRO 807 BK/BK MATT Bedienungsanleitung

Franke

Franke FTF 604 Bedienungsanleitung

Franke

Franke FPL 607 I XS 645H CH LED0 Bedienungsanleitung

Franke

Franke FDW 908 IB XS Bedienungsanleitung

Franke

Franke FME 407 Bedienungsanleitung

Franke

Franke FGB 906 IS Bedienungsanleitung

Franke

Franke FBFE A52 Bedienungsanleitung

Franke

Franke FTC 922 Bedienungsanleitung

Franke

Franke FKAS A80 BK Bedienungsanleitung

Franke

Franke IMPRESS 603 WH Bedienungsanleitung

Franke

Franke FHO 508 BK Bedienungsanleitung

Franke

Franke FCR 908 TC Bedienungsanleitung

Franke

Franke FDF 9156 I XS H100 Bedienungsanleitung

Franke

Franke FMY 608 POT BK Bedienungsanleitung

Franke

Franke FTC 532L GR/XS Bedienungsanleitung

Franke

Franke FTU PLUS 3707 XS Bedienungsanleitung

Franke

Franke 770 OPAL FRI Bedienungsanleitung

Franke

Franke FGC 625 XS NP Bedienungsanleitung

Franke

Franke FRO 908 BK/XS Bedienungsanleitung

Franke

Franke 792-12 Bedienungsanleitung

Franke

Franke 1224B-10 Bedienungsanleitung

Franke

Franke FNO 605 BK Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch