Franke FKU 608 TC Bedienungsanleitung

Istruzioni per l’uso e l’installazione

Cappa

Instructions for use and installation

Cooker Hood

Mode d’emploi et installation

Hotte de Cuisine

Bedienungsanleitung und Einrichtung

Dunstabzugshaube

Kullan

ım ve montaj talimatları

Davlumbaz

FKU 608 TC

FKU 808 TC

FKU 908 TC

Instructions Manual

INDEX

RECOMMENDATIONS AND SUGGESTIONS....................................................................................................................15

CHARACTERISTICS............................................................................................................................................................16

INSTALLATION....................................................................................................................................................................17

USE.......................................................................................................................................................................................20

MAINTENANCE....................................................................................................................................................................21

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance. Accord-

ingly, you may find descriptions of individual features that do not apply to your

specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incor-

rect or improper installation.

• The minimum safety distance between the cooker top and the extractor hood

is 650 mm.

• Check that the mains voltage corresponds to that indicated on the rating plate

fixed to the insideof thehood.

• For Class I appliances, check that the domestic power supply guarantees ade-

quate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum diameter

120 mm.The route of the flue must be asshort aspossible.

• Do not connect the extractor hood to exhaust ducts carrying combustion fumes

(boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances (e.g. gas

burning appliances), a sufficient degree of aeration must be guaranteed in the

room in order to prevent the backflow of exhaust gas. The kitchen must have

an opening communicating directly with the open air in order to guarantee the

entryof clean air.

USE

• The extractor hood has been designed exclusively for domestic use to elimi-

nate kitchen smells.

• Never use the hood for purposesotherthan forwhich it hasben designed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only, making

sure that it does not engulf the sides.

• Deep fat fryers mustbe continuously monitored during use: overheated oil can

burst into flames.

• Do not flambè under the range hood; risk of fire

• This appliance is not intended for use by persons (including children) with re-

duced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use ofthe appliance by a person responsible fortheir safety.

• Children should be supervised to ensure that they do not play with the appli-

ance.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out

any maintenance work.

• Clean and/orreplace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutralliquid detergent.

650 mm min.

CHARACTERISTICS

Dimensions

Components

Ref. Q.ty Product Components

11 Hood Body, complete with: Controls, Light, Blower,

Filters

21 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

91 Reducer Flange ø150-120 mm

14.1 2 Air Outlet Connection Extension

15 1 Air Outlet Connection

Ref. Q.ty Installation Components

7.2.1 2 Upper Chimney Section Fixing Brackets

7.3 1 Air Outlet Connection Support

11 6 Wall Plugs

12a 6 Screws 4,2 x 44,4

12c 6 Screws 2,9 x 9,5

Q.ty Documentation

1 Instruction Manual

2.1

2.2

12c

12a 7.2.1 11

12a

7.3

14.1

INSTALLATION Wall drilling and bracket fixing

Wall marking:

• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the

centre of the area in which the hood will be installed.

• Draw a horizontal line at 650 mm above the hob.

• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit align-

ing the centre (notch) with the vertical reference line.

• Mark the wall at the centres of the holes in the bracket.

• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the

upper chimney section supplied), aligning the centre (notch) with the vertical line.

• Mark the wall at the centres of the holes in the bracket.

• Mark a reference point as indicated at 116 mm from the vertical reference line and 340 mm

above the horizontal reference line.

• Repeat this operation on the other side.

• Drill ø 8 mm holes at all the centre points marked.

• Insert the wall plugs 11 in the holes.

• Fix the lower bracket 7.2.1 using the 12a screws (4,2 x 44,4) supplied.

• Fix the upper bracket 7.2.1 and the air outlet connection support 7.3 together using the 2

screws 12a (4,2 x 44,4) supplied.

• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap

of 5-6 mm between the wall and the head of the screw.

12a

340 X

116

1÷2

116

650 min.

7.2.1

Mounting the hood body

• Before attaching the hood body, tighten the two screws Vr lo-

cated on the hood body mounting points.

• Hook the hood body onto the screws 12a.

• Fully tighten support screws 12a.

• Adjust screws Vr to level the hood body.

12a

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to the

chimney using either a flexible or rigid pipe ø 150 or 120 mm,

the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection, insert the re-

ducer flange 9 on the hood body outlet.

• Fix the pipe in position using sufficient pipe clamps (not sup-

plied).

• Remove any activated charcoal filters.

ø 120ø 150

RECIRCULATION VERSION AIR OUTLET

• Put connection 15 into the connection support 7.3.

• Insert the connection extension pieces laterally 14.1 in connec-

tion 15.

• Make sure that the outlet of the extension pieces 14.1 is hori-

zontally and vertically aligned with the chimney outlets.

• Connect the air outlet connection 15 to the hood body outlet

using either a flexible or rigid pipe ø 150 mm, the choice of

which is left to the installer.

• Ensure that the activated charcoal filters have been inserted.

ø 150

14.1

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch hav-

ing a contact gap of at least 3 mm.

• Remove the grease filters (see paragraph Maintenance) being

sure that the connector of the feeding cable is correctly inserted

in the socket placed on the side of the fan.

Flue assembly

Upper exhaust flue

• Slightly widen the two sides of the upper flue and hook them

behind the brackets 7.2.1, making sure that they are well

seated.

• Secure the sides to the brackets using the 4 screws 12c (2,9 x

9,5) supplied.

• Make sure that the outlet of the extensions pieces is aligned

with the chimney outlets.

Lower exhaust flue

• Slightly widen the two sides of the flue and hook them be-

tween the upper flue and the wall, making sure that they are

well seated.

• Fix the lower part laterally to the hood body using the 2 screws

12c (2,9 x 9,5) supplied.

12c

2.1

2.2

7.2.1

12c

USE

Control panel

Button Function Display

A Turns the suction motor on and off at the

last speed used. Displays the speed set.

B Decreases the working speed. Decreases the lighted segments.

C Increases the working speed. Increases the lighted segments.

D Activates intensive speed from any other

speed, including motor off. This speed is

timed to run for 10 minutes, after which

the system will return to the speed that

was previously set. Suitable for dealing

with severe cooking fumes.

Iflashes and the segments on the Display are

all lit.

It is disabled by pressing the Button.

E Starts the motor at a speed that allows a

suction of 100 m3/h for 10 minutes every

hour, after which the motor stops.

Displays 24 and the segments on the Display,

initially all lit, turn off one at a time in cycle.

It is disabled by pressing the Button.

F Activates automatic switch-off with a 30’

delay. Suitable to complete elimination of

residual odours. Can be activated from any

position, it is deactivated by pressing the

button of turning the motor off.

Displays a flashing Clock symbol.

It is disabled by pressing the Button.

G Performs a Reset of the Filter saturation

alarm when the button is pressed for ap-

proximately 2 seconds.

After 100 hours operation the Drop symbol is

displayed to indicate saturation of the Metal

Grease Filters.

After 200 hours operation the letter Cis dis-

played to indicate saturation of the Activated

Charcoal Filters.

H Turns the Lighting System on and off.

Keyboard Lock Command: it is possible to lock the keyboard, for example when cleaning the

Glass, when the Hood Motor and Lights are turned off.

Press F(Delay) for approximately 5 seconds to enable or disable Keyboard Locking, which is

always confirmed by a Beep and an animated signal on the display motor bar.

CEH

MAINTENANCE

Cleaning the Comfort Panels

• Pull the Comfort Panel to open it.

• Disconnect the panel from the hood canopy by sliding the fix-

ing pin lever.

• The comfort panel must never be washed in a dishwasher.

• Clean the outside using a damp cloth and neutral liquid deter-

gent.

• Clean the inside as well using a damp cloth and neutral deter-

gent; do not use wet cloths or sponges, or jets of water; do not

use abrasive substances.

• When the above operation has been completed, hook the panel

back to the hood canopy and close it by turning the knob in the

opposite direction.

Metal grease filters

Metal filters can be washed also in a dish machine. They need to

be washed every time a drop-symbol appears in the display or at

least every two months. In case of very frequent use these have to

be washed even more often.

Alarm reset

• Press the G-key for at least 2 seconds.

Cleaning

• Open the comfort panel.

• Remove the filters one by one by pushing them backwards and

pulling them down contemporaneously.

• Wash the filters. Pay attention not to bend them. Make sure

that filters are completely dry before putting them into their

seat. (a possible modification of the filter surface doesn’t influ-

ence its efficiency).

• Place the filters again into their seats and make sure that the

handle of the filter remains outside.

• Close the comfort panel.

Charcoal filter (recycling version)

This filter cannot be washed or regenerated. It must be replaced when the C appears on the

display or at least once every 4 months. The filter saturation alarm has to be activated already

before.

Activation of the alarm signal

• In the recycling version hoods the filter saturation alarm must be activated during the instal-

lation or later.

• Switch off the hood and the lights.

• Press the E-key for about 5 seconds until the last two segments of the motor LEDS are lit on

the display.

• By releasing the E-key the clock icon starts to flash.

• Within 3 seconds press the D-key to activate/deactivate charcoal filter saturation alarm.

• C-symbol lit - charcoal filter saturation alarm ACTIVATED.

• C-symbol unlit - charcoal filter saturation alarm DEACTIVATED.

SUBSTITUTION OF THE CHARCOAL FILTER

Alarm reset

• Switch off the motor and the lighting system.

• Press the G-key for at least 2 seconds.

Substitution of the filter

• Open the confort panel.

• Remove the metal grease filters.

• Remove the charcoal filter as indicated in the picture.

• Place the filter again into its seat.

• Place again the metal grease filters into their place.

Lighting

CHANGING LAMP

16 W Neon Lamp

• Open the comfort panel.

• Remove the neon lamp guard by unfastening the screws and

sliding it out of its housing.

• Change the Neon lamp or the Starter, taking care to ensure that

the new components have the same characteristics as the old

ones.

• Replace the neon lamp guard.

• Close the comfort panel.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Franke Dunstabzugshaube Handbücher

Franke

Franke CONCERTO FCO 520 Bedienungsanleitung

Franke

Franke FDL 662 XS Bedienungsanleitung

Franke

Franke FTC 622 Bedienungsanleitung

Franke

Franke FBOX 901 BI X A Bedienungsanleitung

Franke

Franke FFC 905-P XS LED0 Bedienungsanleitung

Franke

Franke FNO 605 BK Bedienungsanleitung

Franke

Franke FBI 537 XS Bedienungsanleitung

Franke

Franke FSTP NG 605 X Bedienungsanleitung

Franke

Franke FBI 537 XS/BK Montage- und Bedienungsanleitung

Franke

Franke FCBI 926 Bedienungsanleitung

Franke

Franke TALE 605 Bedienungsanleitung

Franke

Franke FFI 622 Bedienungsanleitung

Franke

Franke FCBI 1204 C X Bedienungsanleitung

Franke

Franke TIBER Bedienungsanleitung

Franke

Franke ARNO Bedienungsanleitung

Franke

Franke FCMY 90 C WHG A 2B Bedienungsanleitung

Franke

Franke 790 FRI Bedienungsanleitung

Franke

Franke FPJ 705 V BK/SS Bedienungsanleitung

Franke

Franke FTU 3807 I XS 77H Bedienungsanleitung

Franke

Franke FDF 6354 XS Bedienungsanleitung

Franke

Franke Galaxy Slim 2 FX Bedienungsanleitung

Franke

Franke FMYPL 608 POT BK Bedienungsanleitung

Franke

Franke FPJ 605 V Bedienungsanleitung

Franke

Franke FSMS F42 BK MATT Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch