Franke FSW908TC WH Bedienungsanleitung

HANDBOOK HOOD FSW908TC WH/XS 9925084 110.0030.787 UPDATED JANUARY 2010

CONTROL type : PUSH BUTTONS KEY- TOUCH CONTROL

MOTOR : NR 01 330 W

TOTAL POWER : 370 W

FLOW RATE - FREE DELIVERY : 920 M3/H MAX

FLOW RATE IEC 61591 850/740 M3/H MAX

PRESSURE 440 PA MAX

SOUND POWER(IEC 60704-2-13): 66 DBA

NO SPEED POSITIONS : N0 8 + BOOST

LAMPS : NR 02 HALOGEN LAMPS X 20 W each one

LIGHTING SYSTEM CAN BE MODIFIED UP TO FIVE LEVELS.

GREASE FILTER : aluminium cassette

DIAMETER : 150 MM-120 mm adaptor supplied

IMPUT VOLTAGE 230V -50 HZ

TECHNICAL DATA

SPEED BOOST 8 7 6 5 4 3 2 1

Q MAX 920 750 650 550 480 410 350 280 200

Q IEC 850 700 620 530 460 390 330 265 190

P 440 420 400 390 360 320 280 200 100

W 330 220 180 135 110 90 70 50 35

DBA 66 61 58 55 52 49 46 42 35

ELECTRICAL CONNECTION •

Connect the hood to the mains through a two-pole switch having a contact gap of at least 3

mm.

• Remove the grease filters (see paragraph Maintenance) being sure that the connector of the

feeding cable is correctly inserted in the socket placed on the side of the fan.

Metal grease filters Metal filters can be washed also in a dish machine. They need to be washed every

time a drop-symbol appears in the display or at least every two months. In case of

very frequent use these have to be washed even more often. Alarm reset • Press

the G-key for at least 2 seconds.

Cleaning

• Open the comfort panel.

• Remove the filters one by one by pushing them backwards and pulling them

down contemporaneously.

• Wash the filters. Pay attention not to bend them. Make sure that filters are

completely dry before putting them into their seat. (a possible modification of the

filter surface doesn’t influence its efficiency).

• Place the filters again into their seats and make sure that the handle of the filter

remains outside.

• Close the comfort panel.

Hood body mounting Firstly, it is necessary to adjust the two Vr-screws of the 11a-

brackets, at minimun (B).

• Hang the hood body on the two brackets 11a.

• Connect the hood to the mains supply by means of a bipolar switch

with at least 3 mm contact gap.

• Press the “A”-key for one second (see Part USE) to open the upper

panel.

• Remove the metal filters.

• In order to align the hood it is necessary to adjust the Vr-screws

from inside the hood.

• Fasten the safety screw 11.

• Fit again the metal filters into their seats and close the upper panel

by pressing “L”-key for one second (see Part USE).

• Disconnect the hood from the mains supply. Attention: the upper

panel stops if any barrier occurs in its way during the panel opening

or closing.

To open the panel it is enough to remove the barrier and press the

key once again.

KEY- FUNCTION DISPLAY

A Upper panel closed: when pressed for

about one sec-ond it opens the upper panel.

It switches the motor on at the latest selected

speed. Upper panel open: when shortly

pressed it switches the motor on/off

Indicates the selected speed.

B Decreases the suction speed.

The number of lit LEDS decreases.

C Increases the suction speed. The number of lit LEDS increases.

D Functioning only when the upper panel is

open. This speed has been timed at 10

minutes. After that time the system activates

automatically the latest selected speed. The

function is suitable for cooking conditions

when vapours and smells are of the utmost

emission.

I flashes and all the LEDS on the display are lit. By pressing the key

the function is deactived

E Functioning only when the upper panel is

open. By pressing this key it is possible to set

up the motor to a suction speed at 100 m3/h .

24 appears and the LEDS extinguish one by one. By pressing the

key the function is stopped

F Functioning only when the motor is on. By

pressing this key it is possible to set the A flashing clock-symbol appears.

By pressing the key the function is

delayed shutdown of the motor and the

lighting to 30 minutes. stopped

G By pressing this key for about 2 seconds it

is possible to reset the filter saturation alarm

A drop symbol indicates that the metal grease filters saturation alarm

has been activated, and the filters need to be washed. The alarm is

triggered after 100 working hours. C indicates that the charcoal filter

satura-tion alarm has been activated, and the filter has to be

replaced. The alarm s triggered after 200 working hours.

H By pressing this key the intensity of the

lighting system can be modified up to five

levels.

I Upper panel closed: when pressed for about

1 second it opens the upper panel and sets

the lights at the maximum intensity. Upper

panel open: when shortly pressed it switches

the lights on/off.

L Upper panel closed: when pressed for

about one second it opens the upper panel

and switches the motor on at the third speed

and the lights at the maximum intensity.

Upper panel open: when pressed for about 1

second it switches off motor and lights

resetting every activated function, and closes

the upper panel.

Keyboard lock: it is possible to jam the keyboard when, for example, cleaning the glass. The

motor and lights are switched off, and upper panel can be open or closed. By pressing the F-

key (Delay) for about 5 seconds the keyboard block can be activated or de-activated. This

function is confirmed by a Beep and by moving motor LEDS on display.

Charcoal filter (recycling version)

This filter cannot be washed or regenerated. It must be

replaced when the C appears on the display or at least once

every 4 months.

The filter saturation alarm has to be activated already before.

Activation of the alarm signal • In the recycling version hoods

the filter saturation alarm must be activated during the

installation or later.

• Switch off the hood and the lights.

• Press the E-key for about 5 seconds until the last two

segments of the motor LEDS are lit on the display.

• By releasing the E-key the clock icon starts to flash.

• Within 3 seconds press the D-key to activate/deactivate

charcoal filter saturation alarm.

• C-symbol lit - charcoal filter saturation alarm ACTIVATED. •

C-symbol unlit - charcoal filter saturation alarm

DEACTIVATED.

ON OF THE CHARCOAL FILTERSUBSTITUTI

Alarm reset

• Switch off the motor and the lighting system.

ast 2 seconds. Substitution of the filter• Press the G-key for at le

• Open the confort panel.

• Remove the metal grease filters. ated in the picture.• Remove the charcoal filter as indic • Place the filter again into its seat.

Place again the metal grease filters into their place.•

LIGHT REPLACEMENT

20 W halogen light. • Extract the lamp from the lamp holder by pulling gently. • Replace with another of the

ame type, making sure that the two pins are properly inserted in the lamp holder socket holes.s

Replacing the fuse

The hood panel opening and closing mechanism is controlled by a starter motor which is activated by a

fuser.

This fuser works only on the starter motor. In case the fuser gets damaged when the panel is closed it is

be necessary to manually unblock the panel. In this case proceed as follows:

• Remove the cover placed up on the left side.

• Press the releasing lever with the screwdriver as much as necessary to enable the manual opening of

the panel.

• After having completely opened the panel remove the metal grease filters, as explained in the part

concerning the filter cleaning.

• The fuser is placed up on the right side. Turn the fuser holder as indicated. Replace the fuser with one

having the same features.

• Put the fuser holder and grease filters into their place again. Make sure that the hood functions

correctly.

In case the panel doesn’t work correctly it is necessary to contact an authorized technician. If the fuser

gets damaged being the panel open, it is sufficient to simply remove the grease filters and replace the

fuser .

Andere Handbücher für FSW908TC WH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Franke Dunstabzugshaube Handbücher

Franke

Franke Galaxy Slim 2 Energy FX Bedienungsanleitung

Franke

Franke FTU 3805 X Bedienungsanleitung

Franke

Franke FTU PLUS 3707 XS Bedienungsanleitung

Franke

Franke FMPL 606 BK B Bedienungsanleitung

Franke

Franke FVAS A80 BK Bedienungsanleitung

Franke

Franke FCR 925 I TC BK XS Bedienungsanleitung

Franke

Franke Maris Built Under FCBU 1204 2M C WH Bedienungsanleitung

Franke

Franke FBI 705 PLUS Bedienungsanleitung

Franke

Franke FSAS A120 BK/XS Bedienungsanleitung

Franke

Franke FOP 906 Bedienungsanleitung

Franke

Franke FCMY 90 C WHG A FL Bedienungsanleitung

Franke

Franke 782-16 T45 Bedienungsanleitung

Franke

Franke FCBI 1204 C X Bedienungsanleitung

Franke

Franke FMY PRO 907 FM BK/IX Bedienungsanleitung

Franke

Franke FTC 601 GR/XS Bedienungsanleitung

Franke

Franke FBI FLUSH 602 Bedienungsanleitung

Franke

Franke FCO 70 BK MATT Bedienungsanleitung

Franke

Franke ALLIANCE HOOD COMFORT PLUS 1243B-10 Bedienungsanleitung

Franke

Franke 792-10/12 T45 FRI Bedienungsanleitung

Franke

Franke FPL 457 I XS 645H V2 Bedienungsanleitung

Franke

Franke FLI 605 XS LED Bedienungsanleitung

Franke

Franke FMY 607 WH Bedienungsanleitung

Franke

Franke 780 STIL Bedienungsanleitung

Franke

Franke FMA 2.0 PRO 807 BK Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch