Franke FTU 3807 I XS 77H Bedienungsanleitung

Istruzioni per l’uso e l’installazione

Cappa

Instructions for use and installation

Cooker Hood

Mode d’emploi et installation

Hotte de Cuisine

Bedienungsanleitung und Einrichtung

Dunstabzugshaube

FTU 3807 I XS – IN2

Instructions Manual

INDEX

RECOMMENDATIONS AND SUGGESTIONS....................................................................................................................18

CHARACTERISTICS............................................................................................................................................................19

INSTALLATION....................................................................................................................................................................21

USE.......................................................................................................................................................................................26

MAINTENANCE....................................................................................................................................................................27

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting

from incorrect or improper installation.

• The minimum safety distance between the cooker top and the extrac-

tor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply guaran-

tees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm. The route of the flue must be as short as possible.

• Do not connect the extractor hood to exhaust ducts carrying combus-

tion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances

(e.g. gas burning appliances), a sufficient degree of aeration must be

guaranteed in the room in order to prevent the backflow of exhaust

gas. The kitchen must have an opening communicating directly with

the open air in order to guarantee the entry of clean air.

USE

• The extractor hood has been designed exclusively for domestic use to

eliminate kitchen smells.

• Never use the hood for purposes other than for which it has ben de-

signed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only,

making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use: over-

heated oil can burst into flames.

• The hood should not be used by children or persons not instructed in

its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carry-

ing out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

650 mm min.

CHARACTERISTICS

Dimensions

Components

Ref. Q.ty Product Components

11 Hood Body, complete with: Controls, Light, Blower,

Filters

21 Chimney Upper

7.1 1 Telescopic frame complete with extractor, consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

81 Air Outlet Grill

91 Reducer Flange ø150-120 mm

14.1 1 Air Outlet Connection Extension

14.2 1 Air Outlet Extension

15 1 Air Outlet Connection

25 2 Pipe clamps

Ref. Q.ty Installation Components

11 4 Wall Plugs ø 10

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5,2 x 70

21 1 Drilling template

22 4 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual

12h

7.1

12g

7.1a

7.1b

14.1

14.2

12f

12e

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

DRILLING THE CEILING/SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the

template is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert

the Dowels 11 supplied).

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air ex-

haust duct connection.

• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• for Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h,

supplied.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

FIXING THE FRAME

• Unfasten the two screws fastening the upper chimney

stack 2.1 to the frame, and remove the chimney from

the upper stack.

If you wish to adjust the height of the frame, proceed as

follows:

• Unfasten the four safety screws located at the top in

the frame separation area. (A)

• Unfasten the eight metric screws joining the two col-

umns, located at the sides of the frame. (B)

• Adjust the frame to the height required, then replace

all the screws removed as above.

• To guarantee greater stability in the frame, replace

the four safety screws in the last hole available.

• Insert the upper chimney stack from above, and leave

it running free on the frame.

• Lift the frame up, making sure that the index over the

frame plate is turned backwards.

• Fit the frame slots onto the two screws inserted in the

ceiling as above, and turn until reaching the centre of

the adjustment slot.

• Tighten the two screws and fasten the other two

screws provided; before locking the screws com-

pletely, it is possible to adjust the frame by turning it,

making sure that the screws do not come out of their

housing in the adjustment slot.

• The Frame must be securely fastened so as to support

both the weight of the Hood and the stress caused by

occasional axial pressure against the fitted Appliance.

After fixing, make sure that the base is stable even

when the Frame is subjected to lateral stress.

• If the Ceiling is not strong enough in the area where

the hood is to be fixed, the Installer must strengthen

the area using suitable plates and counterplates an-

chored to resistant structures.

Ducted version air exhaust system Connection

When installing the ducted version, connect the hood to

the chimney using either a flexible or rigid pipe ø 150

or 120 mm, the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection, insert

the reducer flange 9on the hood body outlet.

• Fix the pipe using the pipe clamps 25 provided.

• Remove any activated charcoal filters.

ø 120ø 150

Recirculation version air outlet connection

• Insert reducer flange 9on the extractor outlet.

• Push fit connector 15 onto the flange.

• Insert extension piece 14.2 laterally on connector 15,

ensuring that the outlet is in line with the chimney in-

take.

914.1

14.2

Fitting the Upper Chimney and the Hood Body

• Position the upper chimney stack and . x the top of it to the

frame using 2 of the screws removed as above.

• Open the lighting unit by pulling on the notch, disconnect it

from the hood canopy by sliding out the pin.

• Remove the filters one at a time by pushing them towards the

back of the group and pulling down at the same time.

• Remove the activated charcoal filters, if fitted.

• In order to fix the hood body to the frame insert the 4 screws

12f in their seats. It is necessary to leave at least 4-5 mm gap

between the screw heads and the frame plate.

• Hook the hood canopy to the frame and turn it to the left until

it reaches the stop, then lock the screws immediately to prevent

the hood canopy from falling out accidentally.

Recirculation version

• Make sure that the outlet of the extension piece 14.2 is hori-

zontally and vertically aligned with the chimney outlet.

• If this is not the case, remove the lower Chimney Stack and

adjust the position of Extension 14; replace the elements as de-

scribed above.

• Insert Connector Extension 14.1 sideways into Extension 14.2.

• Fit the directional grill 8 into the housing provided. Also make

sure that it is properly fitted into connector 14.1.

14.1

ELECTRICAL CONNECTION

• Connect the hood to the mains through a twopole

switch having a contact gap of at least 3 mm.

• Open the lighting unit by pulling on the notch.

• Remove the filters one at a time by pushing them towards the

back of the group and pulling down at the same time.

• Being sure that the connector of the feeding cable is correctly

inserted in the socket placed on the side of the fan.

• Connect the control connector Cmd.

• Connect the Spotlights connector Lux to the socket provided

behind the lighting unit cover.

• Replace the filters, make sure that the handle is visible on the

outside, and the lighting unit.

Cmd

Lux

Andere Handbücher für FTU 3807 I XS 77H

Inhaltsverzeichnis

Andere Franke Dunstabzugshaube Handbücher

Franke

Franke FTU PLUS 3707 XS Bedienungsanleitung

Franke

Franke FCR 905 BK/XS LED Bedienungsanleitung

Franke

Franke FSMS F42 BK MATT Bedienungsanleitung

Franke

Franke FMA605BK Bedienungsanleitung

Franke

Franke FSAS A90 BK/XS Bedienungsanleitung

Franke

Franke FSAS A120 BK/XS Bedienungsanleitung

Franke

Franke 692-10 Bedienungsanleitung

Franke

Franke FTC 522 Bedienungsanleitung

Franke

Franke FCUH52XSAU Bedienungsanleitung

Franke

Franke 782-17 STIL Bedienungsanleitung

Franke

Franke FTC 601 GR/XS Bedienungsanleitung

Franke

Franke FMYCF 906 Bedienungsanleitung

Franke

Franke FTC 532L GR/XS Bedienungsanleitung

Franke

Franke FSN 908 BK A Bedienungsanleitung

Franke

Franke FNO 605 BK Bedienungsanleitung

Franke

Franke TRENDLINE PLUS 70 Bedienungsanleitung

Franke

Franke FDF EV8 70 Bedienungsanleitung

Franke

Franke FGC 906 I Bedienungsanleitung

Franke

Franke FGC 906 Bedienungsanleitung

Franke

Franke MARIS FMA 605 BK FRK B GF Bedienungsanleitung

Franke

Franke FDB 14078 I Bedienungsanleitung

Franke

Franke FJO 634 XS Bedienungsanleitung

Franke

Franke FSMS F42 SS/BK MATT Bedienungsanleitung

Franke

Franke FTC 612 BK LED1 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch