Franke FTU 3807 I XS 77H Bedienungsanleitung

HANDBOOK HOOD FTU 3807 I XS 77H 9925289 110.0018.185

UPDATED JANUARY 2010

4 SPEED + INTENSIVE

ELECTRONIC PUSH- BUTTONS 4 SPEED + INTENSIVE+ DELAY TIMER+ TO SET UP THE MOTOR

TO A SUCTION SPEED AT 100 M3/H LASTING 10 MINUTES EVERY HOUR+ TURNS LIGHT ON AND

OFF AT REDUCED INTENSITY.

M3/H800 -

DBA 67 -

W 370 -

2 HALOGEN LAMPS X 20 W = TOTAL POWER 40 W

Key Function Display

A Switches the extractor motor on and off at the

latest selected speed Indicates the selected speed.

B Decreases the suction speed.

C Increases the suction speed.

D By pressing this key it is possible to activate the

intensive speed from any previously selected

speed. The intensive speed can be activated even

when the motor is OFF. This speed has been

timed at 10 minutes. After that time the system

activates automatically the latest selected speed.

This function is suitable for cooking conditions

when vapours and smells are of the utmost

emission.

HI appears. The spot down on the right side flashes

once a second.

E By pressing this key it is possible to set up the

motor to a suction speed at 100 m3/h lasting 10

minutes every hour. After this the motor switches

off automatically. When the filter saturation is

going on it is possible to reset the alarm by

pressing this key for about 3 seconds. The

indication is visible only when the motor is off.

Indicates the 24-function. The spot down on the right

side flashes and the motor is on.

Once the process is finished the previous indication

disappears:

FF Indicates that the metal grease filters

saturation alarm has been triggered, and the filters

need to be washed. The alarm is triggered after 100

working hours.

EF Indicates that the charcoal filter saturation

alarm has been triggered, and the filter has to be

replaced; the metal grease filters must also be

washed. The charcoal filter is triggered after 200

working hours.

F By pressing this key it is possible to set the

delayed shutdown of the appliance to 30 minutes.

This function is suitable for a complete elimination

of the residual smells. It can be activated at any

position, and it is deactivated by pressing the key

again or by switching off the motor.

Indicates alternately the selected speed of the hood

and the time left before the hood shutdown. The

spot down on the right side flashes.

G Turns light on and off.

H Turns light on and off at reduced intensity.

Metal grease filters

Filters can be washed in the dish machine. They need to be washed when FF-sign appears on the display or in any

case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset

• Switch off the hood and the lights. If the 24h-function has been activated this has to be deactivated.

• Press the E-key till the display is unlit. Cleaning the filters

• Pull the comfort panels to open them.

• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling

downwards.

• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make

sure that they are completely dry. (The colour of the filter sur-face may change throughout the time but this has no

influence to the filter efficiency).

• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing

outwards.

Charcoal filter (recycling version)

This filter cannot be washed or regenerated. It must be replaced when the EF appears on the display or at least once

every 4 months. Activation of the alarm signal

• In the recycling version hoods the filter saturation alarm must be activated during the installation or later.

• Switch off the hood and the lights.

• Disconnect the hood from the mains supply.

• When restoring the connection press and hold B-key.

• When releasing the key two rotating rectangles appear on the display.

• Within 3 seconds press the B-key until a flashing confirmation appears on the dispaly:

• 2 flashes with EF - charcoal filter saturation alarm ACTIVATED

• 1 flash with EF - charcoal filter saturation alarm DEACTIVATED.

REPLACING THE CHARCOAL FILTER Reset of the alarm signal

• Switch off the hood and the lighting. If the 24h-function has been activated this has to be deactivated.

• Press the E-key until the display is unlit. Replacing of the filter

• Open the comfort panels pulling them downwards.

• Remove the metal grease filters.

• Remove the saturated charcoal filter by releasing the fixing hooks

• Fit the new filter and fasten it in its correct position.

LIGHTING

20 W halogen light.

• Remove the 2 screws fixing

the Lighting support, and pull

it out of from the Hood.

• Extract the lamp from the

Support.

• Replace with another of the

same type, making sure that

the two pins are properly

inserted in the lamp holder

socket holes.

• Replace the Support, fixing

it in place with the two screws

removed as above.

PREPARATION OF THE FRAME FOR THE HOOD IN RE-CYCLING VERSION

In case the hood is used in recycling version it is necessary to prepare the frame with all the

necessary connection pieces. In order to make the installation easier it is necessary to

lengthen the frame:

• Unscrew the two screws fixing the upper chimney to the frame and pull the chimney out.

• Unscrew the four safety screws placed at the top in the frame separation area. (A).

• Unscrew the eight metric screws connecting the two columns, placed on both sides of the

frame (B). Installation of components in recycling version:

• Fix the recycling air outlet piece 15 to the upper part of the frame using four 12c screws

supplied with the hood.

• Fix the flange (ø120) 10 to the lower part of the recy-cling air outlet 15.

• Put the reducer flange 9 on the hood body outlet.

• At this point, join the flanges with a pipe. In order to calculate the height of the pipe it is

necessary to es-timate the height of the hood (mm) and subtract 615 mm. (H pipe = H hood-

615).

• Lengthen the frame so that the pipe can be inserted. Place the pipe between the two flanges

and block it. Make sure that the height of the frame is correct considering the height of the

cooker hood (H frame = H hood – 184). Adjust the height of the frame and tighten again the

earlier removed screws. Tighten again the safety screws in order to give more stability to the

structure.

• Fix the pipe with the pipe clamps 25 supplied with the hood

FIXING THE FRAME

• Lift the frame up, making sure that the index over the frame plate is turned forwards.

• Fit the frame slots onto the two screws inserted in the ceiling as above, and turn until reaching the centre of the adjustment slot.

• Tighten the two screws and fasten the other two screws provided; before locking the screws completely, it is possible to adjust the

frame by turning it, making sure that the screws do not come out of their housing in the adjustment slot.

• The Frame must be securely fastened so as to support both the weight of the Hood and the stress caused by occasional axial

pressure against the fitted Appliance. After fixing, make sure that the base is stable even when the Frame is subjected to lat-eral

stress.

• If the Ceiling is not strong enough in the area where the hood is to be fixed, the Installer must strengthen the area using suit-able

plates and counterplates anchored to resistant structures.

Ducted version air exhaust system Connection

When installing the ducted version, connect the hood to the chimney using either a flexible or

rigid pipe ø 150 or 120 mm, the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body

outlet.

• Fix the pipe using the pipe clamps 25 provided.

• Remove any activated charcoal filters.

Installing of the chimney and fixing of the hood

When the hood is installed in recycling version the chimney has to be positioned with the slots upwards.

When the hood is installed in ducting version it has to be positioned in the opposite way.

• Place the chimney on the frame and fix it to the upper part of it with the earlier removed screws. When

installing the hood in recycling version make sure that the slots correspond to the air outlet of the recycling

air outlet piece 15.

• Open the lighting unit by slightly pulling the notch. Remove the unit from the hood by sliding the fixing pivot.

• Remove the filter pushing it towards the back side of the hood unit and simultaneously pulling downwards.

• Remove possible charcoal filters.

• In order to fix the hood body to the frame insert the 4 screws 12f in their seats. It is necessary to leave at

least 4-5 mm gap between the screw heads and the frame plate.

• Hook the hood canopy to the frame and turn it to the left until it reaches the stop, then lock the screws

immediately to prevent he hood canopy from falling out accidentally.

Electrical connection

• Connect to hood to the mains supply through a double pole switch with at least 3 mm clearance between

the contacts.

• Make sure that the connecting piece of the cable is correctly put in the socket.

• Connect the Cmd-connectors of the controls.

• Connect the Lux-connectors of the lighting system.

• In the recycling hood put the charcoal filter in its place.

• Put the metal grease filter and the confort panel into their proper seats

Position Spare part

code fun number description quantity date in

2 1960200 133.0016.959 SPIGOT 120-150 1 9925289

8 1961142 133.0041.779 TOP FILTERING BENT CHIMNEY X 1 9925289

10 1961143 133.0036.538 LOWER CHIMNEY X D370 F770 1 9925289

12 1960325 133.0017.598 SELF-SUPPORTING FILTER 1 9925289

18 1960084 133.0017.669 BRILLIANT LINE SPOT LIGHT PRO 20W 2 9925289

21 1960905 133.0021.010 PANNEL 1 9925289

27 9925204 112.0016.756 CHARCOAL FILTER/ PANEL 1 9925289

30 1961385 133.0017.004 PIVOT STOPPER NR 02 PIECES 1 9925289

32 1960326 133.0017.597 SPOT LIGHTS SUPPORT HINGE WITH PIN 1 9925289

34 1960309 133.0036.314 CLIP 1 9925289

35 1960906 133.0069.905 GLASS FTU3807IXS ISLAND HOOD 1 9925289

36 1960908 133.0017.779 GLASS SUPPORT FTU NO 2 LAMPS 1 9925289

38 1960972 SCREW FTU 3 9925289

38 1960971 FIXING FTU 3 9925289

39 1960902 133.0021.012 LIGHTING COVER 2 9925289

47 1961144 FLANGE D120 H30 (V2) 1 9925289

101 1960649 133.0017.063 CONTROL W 2T T S.HANSA 1 9925289

Andere Handbücher für FTU 3807 I XS 77H

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Franke Dunstabzugshaube Handbücher

Franke

Franke FDW 908 IB XS Bedienungsanleitung

Franke

Franke FCR 905 Bedienungsanleitung

Franke

Franke FCMY 90 C WHG A FL Bedienungsanleitung

Franke

Franke FCR 625 TC Bedienungsanleitung

Franke

Franke FGL 625 XS NP Bedienungsanleitung

Franke

Franke DRIP 60 Bedienungsanleitung

Franke

Franke FCR 905 BK/XS LED Bedienungsanleitung

Franke

Franke FMA FL 805 Bedienungsanleitung

Franke

Franke FGL 925 I XS NP Bedienungsanleitung

Franke

Franke FGB 906 IS AC Bedienungsanleitung

Franke

Franke FTL 905 Bedienungsanleitung

Franke

Franke FBI 732 XS Bedienungsanleitung

Franke

Franke FS TS 606 W XS Bedienungsanleitung

Franke

Franke FDF 9156 I XS Bedienungsanleitung

Franke

Franke FTU 3807-P WXS 70H Bedienungsanleitung

Franke

Franke FMY 907 MG Bedienungsanleitung

Franke

Franke FNE 915 XS ECS Bedienungsanleitung

Franke

Franke FMPOS 608 BI X Bedienungsanleitung

Franke

Franke FCR 908 TC Bedienungsanleitung

Franke

Franke MYTHOS FMY 367 Bedienungsanleitung

Franke

Franke FTC622XSAU Bedienungsanleitung

Franke

Franke FTC 622 Bedienungsanleitung

Franke

Franke FS VT 906 W XS Bedienungsanleitung

Franke

Franke FCMA 120 C WHG A Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch