Frigidaire FAS Bedienungsanleitung

Installation Instructions

For Hea ry Duty (FAS Models) and

Median (FAM Models) Air Conditioners

Please read ALL instructions before installing. Two people are

recommended to install this product. If a new electrical outlet

is required, have the outlet installed by a qualified electrician

before installing unit. See#5 in Preliminary Instructions

following.

Preliminary Instructions

Do the following before starting to install unit. See illustrations

below.

Check dimensions of your unit to determine model type:

Hea D" duty (FAS) Median (FAJVI)

Unit Height: 18 5/8" 17 5/8"

Unit Width: 26 1/2,, 23 V£'

Min. Window Opening: 19" 18 V2"

Min. Window Width: 31" 26 V2"

Max. Window Width: 43" 40 V£'

I. Check window opening size - the mountingparts furnished

with this air conditioner are made to install in a wooden

sill double-hung window. The standard parts are for

window dimensions listed above. Open sash to a minimum

of !9"(483mm). (FIG. 1)

2. Check condition of window - all wood parts of window

must be in good shape and able to firmly hold the needed

screws. If not, make repairs before installing unit.

FIG. 1

q9" M_N.

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

_LI _LL ANGLE

3. Checkyour storm windows -if your stotlnwindc_w

frame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG. 2, or by removing

stom_window while room air conditioner is being installed.

(continued)

19" MtN_

!_" MIN 11 1/2" MIN,

.................?

] _-n-- [BOARD THICKNESS AS

I L../-/--/< REQUIRED,ALONG

] - -v" " ENTIRE STOOL. FASTEN

STORM WINDOVV FRAME OR WITH TWO NAILS OR

OTHER OBSTRUCTION SCREWS.

P/N 220218A008

4. CHECK FORANYTHING THAT COULD BLOCK

AIRFLOW - check area outside of window for tldngs

such as shrubs, trees, or awrdngs. Inside, be sure

furniture, drapes, or blinds wifl not stop proper airflow:

5. Check the available electrical service -power sut_ly must

be the same as that shown on the unit serial nameplate,

(See Owner's Guide for serial plate location.) Power cord

is 48"loug. Be sure you have an outlet near.

Tools Req uired

%/ a la_e flat blade screwdriver

_/ tape measure

%/ adjustable wrench or pfiers

%/ pencil

%/ Level

%/ Socketwrenches

-./ Phillips screwdriver

All rnodels have a3-prong service plug to provide proper

service and safe positive groudiug. Do not change plug in

any way. Do not use an adapter plug. It'your present wall

outlet does not match your plug, call a qualified electrician

to make the needed change.

NN#,I_: Avoid fire hazard or electric

shock. Do not use an extension oord or an

adaptor plug. Do not remove any prong from

the power cord.

Grounding type wall

receptacle

/6"0 not, under an'y_\

cut,

Nremo_

Power supply cord

with 3-prong grounding

plug and current

detection device

6. Carefully unpack air conditioner - remove all packing

material. Protect floor or carpet from damage. Two

people should be _Lsedto move and i_stall unit.

Hardware (in plastic bag)

Washer Head

LockingScrew

For window panels

3/4" Long Hex-

Head Screw

Safety Lock

1/2"Long Screw

and Locknut

3/4" Long Flat

Head Bolt and

Locknut

Sill Angle Bracket

Long hex-head

locking screw for

top angle, side

retainer 5/16"

Long

Qty.

4 ea.

2ea.

Window Mounting

Remove Chassis

Pull down front panel and remove filter. (See FIG. 1).

Lift front upwards and place to one side.

IL! Install Top Angle

mm and Side Bracket

1. Attach foam gasket to top angle above holes as

shown in FIG. 6.

3, Locate the four front screws and remove. These screw's will

be needed to re-install the front later. (See FIG: 2).

4. Pry away front from cabinet sides as per photo (See FIG. 3).

51 Gently lift front offunit and place to one side (See FIG. 4).

2, Install top

angle and

side retainers

to cabinet as

shown in FIG. 6.

FIG. 6

6. Remove shipping crews from top &unit and also on the side

by the base if installed.

7. Hold the cabinet while pulling on the base handle, and care-

fillly remove the unit.

8. Addtwo foam inserts t,oholes in top of cabinet where

shipping screws were removed from.

Assemble Window

Filler Panels

1. Place cabinet on floor, a bench, or atable.

2. Slide "I" section of window filler panel into side retainer

on the side of the cabinet (see Figures 7-8). Do both

sides.

FIG. 7

PLASTIC V_NDOW FILLER

FRAME PANEL

9, Your unit may come with internal packaging. THIS

PACKAGING MUST BE REMOVED PRIOR TO

INSTALLING THE AIR CONDITIONER BACK

INTO THE CABINET. (See FIG. 5). FIG, 8

SIDE

RETAINER

AIR CO_ioNER PLASTIC

FRAME

"1" SECTION WINDOW HOLE

FILLER

PANEL

3 Insert top and bottom legs of window filler panel frame

into channel in the top angle and bottom rail. Do both

sides.

4. Insertwasher head locking screws (2) into holes in

top leg of filler panel frame (see Step 6). Do not totally

tighten. Allow leg to slide freely. Screws will be

tightened after Section 6.

Place Cabinet in

Window

1. Open window and mark

center of window stool.

Install Support

Bracket

1. Hold each support bracket flush against outside of sill,

and tight to bottom of cabinet as shown below. Mark

brackets at top level of sill, and remove.

MARK

2. Place cabinet in window with bottom stool angle firmly

seated over window stool as shown. Bring window

down temporarily behind top angle to hold cabinet in

place,

3. Shift cabinet left or right as needed to line up center of

cabinet on center line marked on stool.

4. Fasten cabinet to window stool with 2 screws into

holes.(You may wish to pre-drill pilot holes.)

5. Add bottom rail seal over screws to window stool.

L_ !.........1,'2" LONG SCREWS

=r_,= | _/'AND LOCKNUTS

LOCKNUT |_

O, LA GLEb' "/.....O.T

_O_ET............_* I/I

,€

LATH AO _

2EACH REQ!D FOR EACH

SUPPORT BRACKET

2. Assemble sill angle bracket to support brackets at the

marked position, as sho_. Hand tighten, but allow

for any changes later.

3. Install support brackets (with sill angle brackets

attached) to correct hole in bottom of cabinet as shown.

4. Tighten all 6 bolts securely.

1/2"long screws

and Iocknuts

Extend Window Filler

Panels

1. Carefully raise window to expose filler panel locking

screws. Loosen screws so filler panels slide easily.

m Install Chassis into

El Cabinet and Install

Front to Unit

1. Lift air conditioner and carefully" slide into cabinet

leaving 6" protruding.

2. _ DO not push on controls OR finned coils,

3. Be sure chassis is firmly seated towards rear of cabinet

4. Installation of front is the reverse of removal outlined

in Section 1.

2. Extend panels to fill window opening completely.

_Tighten locking screws on top._

3. Close window behind top angle.

Install Window Lock

and Sash Seal

1. "121"inasash seal to fit window width. Insert into space

between upper and lower sashes.

OW SASH SEAL

2. Attach right angle safety lock as shown.

SAF _TY LOCK

3/4"long hex-

_J "_ headscrew

rhru-The-Wall Installation

NOTE: Consult local building codes prior to installation,

or a qualified carpenter.

Select Wall Location

This aft conditioner has aslide-out chassis, so that it canbe

installed through an outside wall as specifed below:

Heavy Duty (FAS) Median (I_AM)

Max wall thiclmess 12" 10,

IMPORTANT: Side louvers must never be blocked.

NOTE: All pa:ts needed for Thru-The-Wall Installation are

provided, except awood fi-ame, shims, and 10 woodscrews (#

10-1" long mininmm). Select a wall surface that:

1, does not support major stractural loads such as the fiame

construction at ends ofwiudows, and :ruder t:uss-bearing

points, etc.

2. does not have plumbing or wiring inside.

3, is near existing electrical outlets, or where another outlet

can be installed.

4. faces, and is not blockedto the area to be cooled.

5. allo_s urLblocked airflow ffomrear sides and end (ontside)

of installed air conditioner.

Prepare Wall

1. Prepare _,all in flame coi_strucfion (including brick and

stucco veneer). Wor!dng fl'om inside the room, find wall

stud nearest the center of area where aft-conditioner will

be installed (by sounding wall, or by magnetically fnding

nails).

2. Cut or knock out ahole on each side of center stud.

3. Meaoqu-ehetweeninside edges of every other stud as shown

in FIG. 1.

FIG. 1

3-3.,'B"MIN

(8.6 cm)

Carefiflly measure and cut artopening with the following

dimeusions depending on yore" model. See FIGS. 1 and 2.

WIDTH "X" = inside model width plus twice the thickness

of flaming material used.

HEIGHT "5?' = inside model height plus twice the thickness

of flaming material used.

Heavy Duty (FAS) Xledian (FAM)

Inside Flmne Height: 187t_"(47,9cm) 18" (45.7cm)

h_side Frame Wide: 26_fd' (67.9cm) 237_" (60.6cm)

FIG. 2

UP TO

8-tt2"

5. Nail flame to spacers to spacers with fforl flushwith

dry_all.

4. Build a wocrden flame with the INSIDE dimensions of

yore- model listed above.(Measure twice remember.,,)

F:ame depth should be the same as wall thickness, Fill in

the s_ace from the opening to the studs with wood spacers,

as shov_a-t.

NOTE:ffwall thicknessis8-1/2"ormore,addalulninum

flashingoverbottomofframeopeningtoassurenowatercan

enterareabetweeninnerandouterwall.

1" LONG

WOOD SCREW

FIG. 2

ALUMINUM FLASHING

OVER BOTTOM OF FRAME

OVER

81/2"

Prepare and Install

Cabinet

Refer to Step 4 of Window Momlting for assembly of support

brackets. A wooden strip nailed to the outside wall should be

used in conjtmction with sill support angle brackets.

1. Slide chassis from cabinet. Refer back to Step 1 of

Window Mounting

2. Place cabinet into opening with bottom rail resting firmly

oll bottom board of wooden frame.

3. Position cabinet to achieve proper slope for water removal.

(See FIG 1 below.)

FIG. 1

5/16"--

318"

LEVEL

314" PLUS

TRIM THICKNESS

SEE PARA 5

Wooden strip

5. Screw or nail cabinet wooden frame using shims if frame

is oversized, to eliminate distortion. Remember to maintain

proper slope as described in Step 3.

4. Secure bottom rail to wood frame with two large wood

screws 1"(2.5 cm) long using the two holes in the bottom

of the channel resting on frame. (See FIG. 2 following) 6. Install chassis into cabinet by following all steps in Step

8 of Window Momlting. (continued)

OPTIONAL:Caulkingandinstallationoftrimoninteriorwall

maybedone.Youcanbuywoodfromyourlocallumberor

hardwaresupply.Ontheoutside,caulkopeningsaroundtop

andsidesofcabinet,andallsidesofwoodsleevetotheopening.

NOTE:SeeStep7,Item3ofWindowMountingInstructions

forbottomrailseallocation.

Masonry Construction

1. Cut or build a wall opening in the masonry wall similar

to the frame construction (refer to Step 2 of Thru-the-

Wall Installation for a wall thickness greater than 8-1/

2").

2. Secure cabinet in place using masonry nails, or the right

masoraT anchor screws. (Another w'ay to do this is to build

an in-between t?ame of 2x4's as shown in the Step 2 Prepare

Wall illustrations-but make it double lYamed on either

side, and install between masonry wall opening and cabinet.

Frame must be securely anchored to masonry, wall

opening) This way gives very good louver clearance on

either side of cabinet.

3. install a lintel to support masonry wall above cabinet.

Existing holes in cabinet can be used ands'or additional

holes can be drilled to fasten cabinet at various positions.

Be sure that side louver clearance is in accordance with

Step 1 above.

4. Install exterior cabient support brackets as shown in

Step 2 of Thru-the-Wall Installation. Caulk or flash if

neede, to provide a wether-tight seal around top and

sides of cabinet.

5. To complete installation, apply wood trim molding

around room side projection of cabinet.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Frigidaire Klimaanlage Handbücher

Frigidaire

Frigidaire FAC053J7A3 Bedienungsanleitung

Frigidaire

Frigidaire FAC065K7A1 Bedienungsanleitung

Frigidaire

Frigidaire CRA050XT73 Bedienungsanleitung

Frigidaire

Frigidaire FFHP094WS1 Bedienungsanleitung

Frigidaire

Frigidaire FAH126M2T1 Bedienungsanleitung

Frigidaire

Frigidaire FAC088L7A1 Bedienungsanleitung

Frigidaire

Frigidaire FRA122BU1 Bedienungsanleitung

Frigidaire

Frigidaire LRA107BU113 Betriebsanleitung

Frigidaire

Frigidaire FAC055J7A3 Bedienungsanleitung

Frigidaire

Frigidaire LRA08PZU113 Bedienungsanleitung

Frigidaire

Frigidaire FAS226R2A - Heavy Duty Room 22,000 BTU Air Conditioner... Bedienungsanleitung

Frigidaire

Frigidaire FAK085R7V - Slider/Casemen Room Air... Bedienungsanleitung

Frigidaire

Frigidaire FAC106P1 Bedienungsanleitung

Frigidaire

Frigidaire FAC105L1A2 Bedienungsanleitung

Frigidaire

Frigidaire FFRE153ZA1 Bedienungsanleitung

Frigidaire

Frigidaire FAH096M2T1 Bedienungsanleitung

Frigidaire

Frigidaire 220201d036 Bedienungsanleitung

Frigidaire

Frigidaire FAK127P1V Bedienungsanleitung

Frigidaire

Frigidaire Split Type Room Air Conditioner Bedienungsanleitung

Frigidaire

Frigidaire Home Comfort FRA123PT1 Montageanleitung

Frigidaire

Frigidaire Designer Series Bedienungsanleitung

Frigidaire

Frigidaire FAH126N2 Bedienungsanleitung

Frigidaire

Frigidaire FRP77PTT2R Bedienungsanleitung

Frigidaire

Frigidaire FRA103KT1 Service-Handbuch

Beliebte Klimaanlage Handbücher anderer Marken

Spheros

Spheros CC 355 Bedienungsanleitung

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Bedienungsanleitung

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Samsung

Samsung AR KV Series Leitfaden

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

Hitachi

Hitachi RAS-E24CAK Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Hisense

Hisense 7K Technisches Handbuch

Samsung

Samsung AS09HM3N Bedienungsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung