Frigidaire FFRE25L3Q20 Bedienungsanleitung

For Medium (15,000-18,500BTU) + Heavy duty (22,000-28,500BTU)Air Conditioner

READ BEFORE INSTALLING UNIT

Carefully read the installation manual before beginning.

Follow each step as shown.

Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.

Pay attention to danger and safety notices.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may

be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install

the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To

prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended

period of time.

Handle air conditioner with care.

Make sure air conditioner does not fall during installation.

If a new electrical outlet is required, have the outlet installed by a qualified electrician before installing unit.

NOTE: DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE.

Preliminary instructions: window sash seal

Do the following before starting to install unit. See illustrations below.

Check dimensions of your unit to determine model type: safety lock and

Heavy duty Medium 1/2" long

head screw

Capacity: 22,000-28,500 BTU 15,000-18,500 BTU

Unit Height: 18-5/8" 17-5/8" foam c

Unit Width: 26-1/2" 23-5/8" washer head

locking

Min. Window Opening: 19-1/2" 18-1/2"

Min. Window Width: 31" 26-1/2" frame

Max. Window Width: 42" 40-1/2" (left)

1. Check window opening size: the mounting parts

furnished with this air conditioner are made to install in side retainer

a wooden sill double-hung window. The standard parts

are for window dimensions listed above. Open sash to 1/2" long

a minimum of 19" (483mm). (FIG.l) screws and

bottom rail Iocknuts --,

2. Check condition of window: all wood parts of window seal to unit x,

must be in good shape and able to firmly hold the needed ] window frame

Iort bracket assembly

screws. If not, make repairs before installing unit. long flaL_, \ .._ (right)

3. Check your storm windows: If your storm window "_ead bolt 6."/

sill angle

frame does not allow the clearance required, correct by _ bracket

adding a piece of wood as shown (FIG.2), or by removing

storm window while room air conditioner is being installed. _'1

FIG.1 _ --sash I F,G.2 ___sash

i"min

1/2",_min i inner, sill

storm window frame or

other obstruction

19" min

112" min 11-1/2" min /

, F"__ inner sill

|_oard thickness as

I ____--_¢'_ required, along entire inner

window sill; fasten to inner

storm window frame or sill with two nails or screws.

other obstruction 2020218A1534

4. Check for anything that could block airflow

Check area outside of window for things such as shrubs, trees, or awnings. Inside, be sure furniture, drapes, or blinds

will not stop proper air flow.

5. Check the available electrical service

Power supply must be the same as that shown on the unit serial

nameplate. (See Use & Care Guide for serial plate location.) Power

cord is 46" long. Be sure you have an outlet near.

All models have a 3-prong service plug to provide proper service and

safe positive grouding. Do not change plug in any way. Do not use an

adapter plug. If your present wall outlet does not match your plug, call

a qualified electrician to make the needed change.

6. Carefully unpack air conditioner

Remove all packing material. Protect floor or other stable flat surface

with covering to prevent scratches from unit. With the aid of an

assistant, remove unit from styrofoam base and rest on protected

surface. Move and install unit with the aid of an assistant. Save

packing and shipping box for future unit storage.

Accessory Kit includes

• Hardware bag(shipped inside • Foam gasket

window support brackets)

• Window support bracket (2) • Window sash seal

• Side retainer (2) ® Bottom rail seal

® Window Filler Panel (2) , Top angle rail

MEDIUM models only

HEAVY DUTY top angle rail can be found in carton base

packaging (FIG.3)

Tools Required

® a large flat blade screwdriver • tape measure

o adjustable wrench or pliers • pencil

• level • Socket wrenches

•Phillips screwdriver

Avoid fire hazard or electric

shock. Do not use an extension cord or an

adaptor plug. Do not remove any prong

from the power cord.

-- Grounding Prong

Do not, under any

circumstances, cut,

remove or bypass the

grounding prong.

Remark: The appearance of actual plug may

be slightly different from the line drawing shown

in the figure, The line drawings are for

reference only.

HEAVY DUTY FIG,3

(22,000~28,500BTU)

TOP ANGLE RAIL

Hardware Qty. Hardware Qty.

_-_ 7/16" Locking Screw and Flat 2ca _ Sill Angle Bracket 2

Washer for window filler panels

(_ (_ Long hex-head locking screw for top1/2" Long hex head screw 7 angle rail, side retainer 5/16" long I 0

<_t Safety LockSafety Lock I (for Vinyl-Clad window) 2

_ 1/2" Long Screw 4 ea _ Locking screw #10 X 1/4" panheadand Iocknut Phillips screws (for Vinyl-Clad window) 2

_O 3/4" Long Flat Head Bolt 2 ea weather seals 5

and Locknut (6"x314"Xl112")

_ foam insert 2

Window Mounting

Remove Air Conditioner from Cabinet

NOTE: Remove any packaging material from cabinet exterior.

t. Pull down on front grille from upper edge. Lift front grille upwards and place to one side. (See FIG.l)

2, Remove filter. To remove, grasp in the middle on each side. Bow filter out to detach top edge from tabs. Once top

is free, lift filter up and out, FIG.2

FI__ Front Grille _ .................._ '-_-_

t:t_ .... /

_ -_d I-I I_

3. Locate the four Front Panel screws and remove. These screws will be needed to re-install the Front Panel later

(See FIG.2).

4. Push metal cabinet side inward to release plastic tabs on each side of Front Panel (see Fig. 3).

5. Rotate Front Panel up until top tabs are free. Pull panel straight out. When pulling out, front panel will also pull free

from vent control lever. Depress latch on electronics plug (on some models) to disconnect,

6. Remove Front Panel from unit (see Fig. 4).

FI 1i, i.....

FIG.4

base pan handle

7. Remove shipping screws from top of unit and also on both sides by the base if installed. (See FIG.5)

8. With the aid of an assistant, hold the cabinet while pulling on the base pan handle (see FIG. 4), and carefully

remove the air conditioner from cabinet,

9. Add two foam inserts to holes in top of cabinet where shipping screws were removed from. (See FIG.6)

10. Except 22,000BTU model, other heavy duty models (24,000-28,500BTU) come with internal shipping packaging.

THIS PACKAGING AND PLASTIC TIES MUST BE REMOVED PRIOR TO INSTALLING THE AIR CONDITIONER

BACK INTO THE CABINET. (See FIG.7)

11. Remove plastic wrapping from all points on power cord. _,_ FIG.7

-/_ Shipping Packaging i

F,G.6 P,astictie

ins II Top Angle Rail and Side Retainers t_-I I

t. Remove adhesive strip coating from foam gasket. Attach adhesive side of gasket to bottom of top angle rail. Insert

four 5/16" screws from inside of cabinet and secure to top angle rail. FIG.8

2. From inside of cabinet insert three 5/16" screws to attach each side retainer as

shown in Fig. 8.Attach side retainers with flat side against cabinet and angled edge

toward rear of cabinet.

_ Assemble Window Filler Panels

t. Place cabinet on floor, a bench, or a table.

2. Slide "]" section at end of window filler panel into side retainer on each side of the

cabinet (see FIG. 9 and FIG.10).

3. On each side of cabinet, insert top and bottom legs of window filler panel Foam Gasket

frame into channel in the top and bottom angle rails.

4. Insert a 7/16" locking screw and flat washer into hole on top leg of each window filler panel (see section 6). Do not

totally tighten, Allow leg to slide freely, Screws will be tightened after Section 6.

angle rail

FIG.9 Top windowfiller WINDOW FILLER

panel leg PANEL

filler panel leg

dL]

;IDE RETAINER

_Place Cabinet in Window

1. Open window and mark the center of window inner sill as shown (FIG. 11).

2. Place cabinet in window with cabinet bracket securely seated over edge of inner sill as shown

in FIG. 12. Bring window down temporarily behind top angle rail to hold cabinet in place.

3. Shift cabinet left or right as needed to line up center of cabinet on center line marked on inner

sill.

4. For wooden window: Fasten cabinet to window inner sill with two 1/2" long hex head screws

into holes (FIG.13A). (You may wish to pre-drill pilot holes.)

For Vinyl-Clad window: Place two safety locks into the holes located in the bottom of

the cabinet and drive two #10Xl/4" pan-head Phillips locking screws through the safety locks

into the cabinet as shown (FIG.13B).

5. Remove protective strip from adhesive side of Bottom Rail Foam Seal.

Apply Seal over screws fastening bottom rail to window inner sill. ..................

FIG.12 Angle of cabinet

bracket securely seated

on edge of inner sill.

window I F-J Bracket

inner sill I ]

window I

outer sill

install Support Bracket

FIG.10 TOP VIEW

i AIR CONDITIONER ] PLASTIC

'x: I I J LOCKING

"1"SECTION _ _ SCREW HOLE

WINDOW

FILLER

PANEL

1. Hold each support bracket flush against outside of sill and tight to bottom of cabinet. Mark brackets at top level of

sill. Mark cabinet bottom at distance of sill width. See Fig. 15 A. Remove support brackets.

2. Attach sill angle brackets to support brackets at marked positions with flat head bolts and nuts. Hand tighten only

at this point. See Fig. 15B.

3. Insert 1/2" long bolts through appropriate holes in cabinet bottom given the sill width distance. Thread the bolts into

the slots of the support brackets. Tighten lock washer nuts onto bolts.

4. Adjust height of sill angle bracket so that bracket rests securely on edge of sill, and so that cabinet has about 7/8" to

1 1/4" downward tilt for proper water drainage (tilted about 2° to 4° downward to the outside, see Fig. 14). Tighten nuts

securely. After proper installation, condensate should not drain from the overflow drain hole during normal use, correct

the slope otherwise.

FIG.14 _/WindowS:_ut718,_ l l/4.j '

_mWin doSw_]_1_gle Bracket FIG.15A MAF_'Rb"

FIG.15B __ !/2" LONG SCREWS

LOCKN:ET_/_AND LOCKNUTS

SlLL ANGLE _¢//

BRACKET 7_ _ _" _Z_ R,GHT

FLAT HEAD-_BBOLT

2 EACH REQ'D FOR EACH

SUPPORT BRACKET

_ Extend Window Filler Panels and attach to angle rail:

top

1. Carefully raise window to expose filler panel locking screws on top angle rail. Loosen screws so filler panels slide

easily.

2. Extend panels to fill window opening completely. Tighten locking screws on top (FIG. 16).

3. Close window behind top angle rail.

4. Attach the top angle rail to window frame: Use a 3/32" drill bit to drill one hole through the hole in the middle of top

angle rail into the window frame, and drive one 1/2" HEX_HEAD locking screw through the hole in the middle of top

angle rail into the window frame as shown (FIG. 17).

FIG.16 FIG. 17

-t'_/16" Locking Screw

and Washer

_Attach Window Filler Panels to Window Frame

t. Extend the window filler panels out against the window frame.

2. Use a 1/8" drill bit to drill a starter hole through the hole in the

top leg of each window filler panel and into the window sash

(Fig. 18A and Fig. 18B). Connect with one 1/2" long hex head

screw.

t,ll install Window Sash Seal and Safety Lock

1. Trim window sash seal to fit window width. Insert it into

space between upper and lower sashes as shown (FIG. 19).

2. Attach right angle safety lock to top window sash as

shown (FIG.20).

3. If necessary, trim weather seals to needed length, peel

off protective backing, and use to plug any gaps. See Fig. 18B.

FIG. 18A

d B

A, 1/2" long hex head screw

B. left-hand Window Filler

Panel Top Leg

C. Window channel

FIG.19

FIG.20

install Air Conditioner into Cabinet and install Front Panel to Unit

1/2" long

HEX-HEAD

SCREW

i"iii.l' .'_ we a thFelG i: :1:

A. 1/2" long hex head screw

FIG. 21

t. Lift air conditioner and carefully slide into cabinet.

2. CAUTION: Do not push on controls OR finned coils.

3. Be sure air conditioner is firmly seated towards rear of cabinet.

4. Reconnect electronics plug if present, Position vent control lever so that it will thread into its channel in the front

panel (see FIG.21). Hook front panel top tabs into slots on cabinet top, and rotate front panel down so that side tabs

snap into place on cabinet. Insert 4 previously removed screws through front panel and into air conditioner.

5. Insert air conditioner filter. Reinstall the front grille by hooking bottom tabs into slots on Front Panel bottom, then

rotating grille up to snap into place,

)ntrol

correct location

Thru-The=Wall Installation

® Consult local building codes prior to installation, ora qualified carpenter.

HSelect Wall Location

This air conditioner slides out from its cabinet, so that it can be installed through an outside waft as explained

below.

Heavy duty Medium

Max wall thickness 10" 8"

oIMPORTANT: Side louvers must never be blocked.

= All parts needed for Thru-The-Wall Installation are provided, except a wood frame, shims, and 10 wood screws

(#10_1" long minimum). Select a wall surface that:

1. Does not support major structural loads such as the frame construction at ends of windows, and under

truss-bearing points, etc.

2. Does not have plumbing or wiring inside.

3. Is near existing electrical outlets, or where another outlet can be installed.

4. Faces to the area to be cooled, and it is not blocked.

5. Allows unblocked airflow from rear sides and end (outside) of installed air conditioner.

Prepare Wall

1. Prepare wall in frame construction (including brick and stucco veneer). Working from inside the room, find wall stud

nearest the center of area where air conditioner will be installed (by sounding wall, or by magnetically finding nails).

2. Cut out a hole on each side of center stud.

3. Measure between inside edges of every other stud as shown in FIG.1. Carefully measure and cut an opening with

the following dimensions depending on your model. See FIG.1 and FIG.2.

WIDTH "X" = inside model width plus twice the thickness of framing material used.

HEIGHT "Y" = inside model height plus twice the thickness of framing material used.

Heavy Duty Medium

3-3/8"

Capacity: 22,000-28,500BTU 15,000-18,500BTU

Inside Frame Height: 18-7/8" (47.9 cm) 18" (45.7 cm)

Inside Frame Width: 26-3/4" (67.9 cm) 23-7/8" (60.6 cm)

FIG.1 ::

(8.6 cm)

FIG.2

4.BuildawoodenframewiththeINSIDEdimensionsofyourmodellistedabove.(Measuretwiceremember...)Frame

depthshouldbethesameaswallthickness.Fillinthespacefromtheopendingtothestudswithwoodspacers,as

shown.

5.Nailframetospacerstospacerswithfrontflushwithdrywall.

• Ifwallthicknessis8-1/2"ormore,addalumimumflashingoverbottomofframeopeningtoassurenowatercan

enterareabetweeninnerandouterwall.

NAiLSPACERS

i! i TOSTUDS

,,,, :::: F,G.4

ALUMINUM FLASHING

OVER BOTTOM OF FRAME

_Prepare and install Cabinet

t. Slide air conditioner from cabinet; refer back to Step 1 of Window Mounting.

2. Place cabinet into opening with bottom rail resting firmly on bottom board of wooden frame.

3. Position cabinet to achieve proper downward tilt for water removal. Unit must tilt back about 7/8" to 1 1/4" for proper

water drainage. (See FIG.5 below.)

4. Secure bottom rail to wood frame with two large wood screws 1" (2.5 cm) long using the two holes in the bottom of

the channel resting on frame. (See FIG.6 following)

FIG.5 F-q FIG.6

, _ about 7/8"- 1 1/4"

I' I"LONG

WOOD SCREW

Side Louvers

Refer to Step 5 of Window Mounting for assembly of support brackets. Nail a wooden strip to the outside wall for the

angle sill bracket to rest upon. See Fig. 7.

5. Screw or nail cabinet to wooden frame using shims as needed to eliminate cabinet distortion. See Fig. 8. Remember

to maintain proper tilt as described in Step 3.

FIG.7 FIG.8

port bracket

ngle bracket

6. Install air conditioner into cabinet by following all steps in Step 9 of Window Mounting.

OPTIONAL: Caulking and installation of trim on interior wall may be done. You can buy wood from your local lumber or

hardware supply, On the outside, caulk opendings around top and sides of cabinet, and all sides of wood sleeve to the

opening,

® See Step 5, Item 4 of Window Mounting Instructions for bottom rail seal location.

Masonry Construction

I. Cut or build a wall opening in the masonry wall similar to the frame construction (refer to Step 2 of Thru-the-Wall

Installation for a wall thickness greater than 8-1/2").

2. Secure cabinet in place using masonry nails, or the right masonry anchor screws. (Another way to secure cabinet is

to build a frame in the masonry wall such as the one shown in Fig. 3 of Step 2 Prepare Wall. Securely anchor frame to

masonry wall. This way gives very good louver clearance on either side of cabinet.)

3. Install a lintel to support masonry wall above cabinet. Existing holes in cabinet can be used and/or additions holes

can be drilled to fasten cabinet at various positions. Be sure that side louver clearance is in accordance with Step 1

Select Wall Location.

4. Install exterior cabinet support brackets as shown in Step 3 of Thru-the-Wall Installation. Caulk or flash if needed, to

provide a weather-tight seal around top and sides of cabinet.

5. To complete installation, apply wood trim molding around room side projection of cabinet.

Andere Handbücher für FFRE25L3Q20

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Frigidaire Klimaanlage Handbücher

Frigidaire

Frigidaire Home ComfortFRA086HT1 Bedienungsanleitung

Frigidaire

Frigidaire FAA085P7A Bedienungsanleitung

Frigidaire

Frigidaire FAK124P1V1 Bedienungsanleitung

Frigidaire

Frigidaire Room Air Conditioner Bedienungsanleitung

Frigidaire

Frigidaire LRA067AT7 Betriebsanleitung

Frigidaire

Frigidaire FAC051K7A4 Bedienungsanleitung

Frigidaire

Frigidaire FAC053L7A1 Bedienungsanleitung

Frigidaire

Frigidaire FAC124N1A2 Kurzanleitung

Frigidaire

Frigidaire FAH12EN2T Bedienungsanleitung

Frigidaire

Frigidaire FHWW183WC2G Betriebsanleitung

Frigidaire

Frigidaire FFRA0511Q19 Betriebsanleitung

Frigidaire

Frigidaire Home Comfort FRA124HT1 Bedienungsanleitung

Frigidaire

Frigidaire FRA113PT110 Bedienungsanleitung

Frigidaire

Frigidaire FAC051K7A6 Kurzanleitung

Frigidaire

Frigidaire FAA055P7A 5,200 Bedienungsanleitung

Frigidaire

Frigidaire ELECTRONIC CONTROL AIR CONDITIONER Betriebsanleitung

Frigidaire

Frigidaire FRA102BT110 Betriebsanleitung

Frigidaire

Frigidaire FRA156MT1 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Frigidaire

Frigidaire FFRH1222Q20 Betriebsanleitung

Frigidaire

Frigidaire FFRA102WAE Bedienungsanleitung

Frigidaire

Frigidaire Home ComfortFRA08PZU1 Montageanleitung

Frigidaire

Frigidaire FAX052P7AD Bedienungsanleitung

Frigidaire

Frigidaire FAH14EQ2T4 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PUZ-SM100VKA Bedienungsanleitung

Airwell

Airwell Dakota DCI Series Bedienungsanleitung