Frigidaire FRA08PZU113 Bedienungsanleitung

FRIGIDAIRE

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii__

iii¸/im

Product

ackaging .;,

aormat sounds :L

www,frigJ

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as

instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that

may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.

The power supply cord with

this air conditioner contains a current

detection device designed to reduce the risk

of fire.

UPlease refer to the section 'Operation of

Current Device' for details.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance. Read product labels for flammability and other warnings.

In the event that the power supply cord is Prevent Accidents

damaged, it cannot be repaired, tt must be

replaced with a cord from the product To reduce the risk of fire, electrical shock, or injury to persons when using your air conditionel

manufacturer, followbasicprecautions,includingthefollowing:

° Be sure the electrical service is adequate for the model you have chosen. This information

Avoid fire hazard or electric shock. Do not

use an extension cord or an adaptor plug. Do

not remove any prong from the power cord.

can be found on the serial plate, which is located on the side of the cabinet and behind the

grille.

• If the air conditioner is to be installed in a window, you will probably want to clean both

iiii ii sides of the glass first. If the window is a triple-track type with a screen panel included,

remove the screen completely before installation.

• Be sure the air conditioner has been securely and correctly installed according to the

separate installation instructions provided with this manual. Save this manual and the

installation instructions for possible future use in removing or reinstalling this unit.

•When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front

and rear coils.

DANGER.IAvoid Serious Injury or Death

This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.

Do not insert or place fingers or objects into the air discharge area on top of the unit.

Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.

Do not cut or damage the power cord.

If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.

In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized

Electrolux servicer.

• Do not operate the air conditioner with wet hands.

• Do not pull on the power cord.

• Do not drink any water that is drained from the air conditioner.

CAUTION. IAvoid Injury or damage to the unit or other property

Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make

units run excessively.

Do not climb on or place objects on the unit.

Do not hang objects off the unit.

Do not place containers with liquids on the unit.

Turn off the air conditioner at the power source when it will not be used for an extended period of time.

Periodically check the condition of the unit's installation accessories for any damage.

Do not apply heavy pressure to the radiator fins of the unit.

Operate the unit with air filter in place.

Do not block or cover the intake grille, discharge area and outlet ports.

Ensure that any electrical/electronic equipment is one yard away from the unit.

Do not use or store flammable gases near the unit.

READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.

Unit must be upright for one hour prior to operating.

Operation of Current

Device

Plug in & _,

press RESET

The power supply cord contains a current device that senses damage to the power cord. To test

your power supply cord do the following:

1. Plug in the Air Conditioner.

2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will

notice a click as the RESETbutton pops out.

3. Press the RESET button, Again you will notice a click as the button engages,

4. The power supply cord is now supplying electricity to the unit,

•Do not use this device to turn the unit on or off.

•Always make sure the RESET button is pushed in for correct operation.

•The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,

or it cannot be reset. A new one can be obtained from the product manufacturer.

If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained

from the product manufacturer.

Product Registration Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. On all models, the

serial plate is located on the outside of the cabinet.

Model No.

Serial No.

The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,

signed and returned to the Frigidaire Company.

Packaging Remove all packaging from inside the carton, along with any

inserts placed into the side louvers.

PACKAGING INSERTS

Normal Sounds High pitched Chatter

Today's high efficiency compressors

may have a high pitched chatter

during the cooling cycle.

Sound of Rushinq Air

At the front of the unit, you may

hear the sound of rushing air

being moved by the fan.

Gurgle/Hiss

"Gurgling or hissing" noise may be

heard due to refrigerant passing

through evaporator during normal

operation.

Vibration

Unit may vibrate and make noise

because of poor wall or window

construction or incorrect installation.

Pinging or Swishing

Droplets of water hitting condenser

during normal operation may cause

"pinging or swishing" sounds.

Air Conditioner Features ELECTRONIC CONTROL

Before you begin, thoroughly familiarize yourself with the control panel and remote

as shown below and all its functions, then follow the symbol for the functions you

desire. The unit can be controlled by the touch pad alone or with the remote.

DISPLAYS

TEMPERATURE/TIME

cool

econ

fan only

temp/dmer

auto l

CHECK FILTER

RESET BUTTON

fi [te rJ

reset

timer MODE

ACTIVATES j

TIMER

SETS MODE

V ON=OFF AFAN SPEED steep

[ T, [....

TURNS UNIT

/ONOROFF| |

L ADJUSTS ___J LSETS FAN

TEMPERATURE SPEED

SLEEP MODE

_ o

fTEMP/T]MER

TEMP/TIMER

coot energy fan

saver only

steep auto timer

fan

FRIGIDAIRE

OR TIME

Battery Size: AAA

Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc),

or rechargeabte (nickel-cadmium) batteries.

STANDARDREMOTE

Operating Instructions

The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.

TO TURN UNIT ON: YOU WILL SEE:

temp/timer auto I

cool _ _ hi I

econ _ _ med I

fan only _to ]

MODE V 0N-0FF A FAN SPEED

_1_ DO THIS

PRESS ON/OFF BUTTON I

Itemp/timer Fauto I

.cool _ _ hi " I

econ _"J_ | meg I

fan only _ lo ,J

MODE V 0N-0FF AFAN SPEED

Operating Instructions

(continued)

TO CHANGE TEMPERATURE SETTING: YOU WILL SEE;

ternp/timer

Fauto l

hi ,,

reed

fi [t er

reset

V 0N=0FF AFAN SPEED

--% ?

_ PRESSA TO RAISE

I"PRESSV TO LOWER

steep

temp/timer l

hi ,, fitter

reed reset

V ON=0FF A FAN SPEED steep

Note: Tap or hold either up ( A) or down ( V) button until

the desired temperature is seen on the display. This tempe-

rature will be automatically maintained anywhere between

60 °F (16 °C) and 90 °F (32 °C). If you want the display to

read the actual room temperature. See "To Operate on Fan

Only" section on Page 7.

TO ADJUST FAN SPEEDS: YOU WILL SEE:

temp/timer

Fauto I

hi ,,

reed

0N-0FF A FAN SPEED

fitter

reset

steep

temp/timer

Fauto i

hi fitter

reed reset

lo m

V ON-OFF A FAN SPEED steep

DO THIS:

PRESSTO SELECT

TO USE AUTO FAN FEATURE; YOU WILL SEE:

temp/timer

Fauto I

hJmecl

lo _

V 0N-OFF A FAN SPEED

fi[t er

reset

steep

DO THIS:

PRESSFAN BUTTON,

CHOOSE AUTO

temp/timer

Fauto m

hi fitter

reed reset

V 0N-0FF A FAN SPEED steep

Note: Fan starts at High Speed and adjusts to a slower

speeds the room temperature dictates. For example, if the

room doesn't get too warm, it will stay at the slowest speed.

If the room temperature rises quickly, such as a door being

opened, it will automatically go to the highest speed. The fan

speeds will re-adjust back to the slowest speed as the room

returns to the original set temperature. Press either the fan

slower or fan faster button to adjust the fan speed manually.

Operating Instructions

(continued)

TO OPERATE ON FAN ONLY: YOU WILL SEE:

timer

I tom Jt,mo

"cool F

econ

#n only

MODE V ON-OFF A

DO THIS:

PRESS

MODE BUTTON

CHOOSE

FAN ONLY

Icool

econ

==Jan only

temp/timer

timer MODE V 0N-0FF A

Note: Use this function only when cooling is not desired,

such as for room air circulation or to exhaust stale air on

some models. (Remember to open the vent during this

function, but keep it closed during cooling for maximum

cooling efficiency.) You can choose any fan speed you

prefer. (Except "Auto Fan").

During this function, the display will show the actual room

temperature, not the set temperature as in the cooling

mode.

TO USE THE ENERGY SAVER (ECON) FEATURE:

cool

Lecon

" #n only

temp/timer F

timer MODE V ON-OFF A

YOU WILL SEE:

I cool

"econ

fan only

temp/timer

timer MODE V ON=OFF ^

DO THIS;

PRESS

MODE BUTTON

CHOOSE ECON

Note: In this mode, the fan will continue to run for 1 minu-

te after the compressor shuts off. The fan then cycles on

for 20 seconds at 10 minute intervals until the room tempe-

rature is above the set temperature, at which time the com-

pressor turns back on.

SLEEP FEATURE: YOU WILL SEE:

temp/timer Fauto I

EIIJll _ meal I

v ON-OFF A

filter

reset

FAN SPEED sleep

----7---

DO THIS;

PRESS

SLEEP BUTTON

temp/timer

V0N-0FF A FAN SPEED

Fauto I

hi "filter

reed reset

sleep

Note: In this mode the selected temperature will increase

by 2 °F 30 minutes after the mode is selected. The tempe-

rature will then increase by another 2 °F after an additional

30 minutes. This new temperature will be maintained for 7

hours before it returns to the originally selected tempera-

ture. This ends the "Sleep" mode and the unit will continue

to operate as originally programmed. The "Sleep" mode

program can be cancelled at any time during operation by

again pressing the "Sleep" button.

Operating Instructions

(continued)

TIMER: DELAY STOP /START FEATURE

timer

mCOOl

econ

_n only

MODE

\\ FIRST

DO THIS:

PRESS

TIMER BUTTON

temp/timer

ON-OFF A

THEN

DO THIS;

PRESS

UP/DOWN BUTTONS

YOU WILL SEE HOW MUCH TIME IS CHOSEN;

•, cool

econ

fanonly

temp/timer

timer MODE V ON-OFF A

Note: For Delay Stop, the unit must be in the On position.

Note: For Delay Start, the unit must be in the Off position.

First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( A ) or the DOWN arrow ( V ) to change delay

timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time

remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool,

Energy Saver, or Fan Only was the last mode selected) . The temperature maintained will be the same as previously set. To change

the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5

seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the

unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either

starts or stops. Once that happens the above steps have to be repeated again.

CHECK FILTER FEATUREr YOU WILL SEE:

temp/timer l

ou o.

hi fitter

med reset

V ON-OFF A FAN SPEED steep

Note: This feature is a reminder to clean the Air Filter (See

Care and Cleaning) for more efficient operation. The LED

(light) will illuminate after 250 hours of operation. To reset

after cleaning the filter, press the "Filter Reset" button and

the light will go off.

temp/timer

Fauto m

fi [ter

reset

V ON=OFF A FAN SPEED steep

DoT.,s;/I

PRESS FILTER

RESET BUTTON

FAULT CODES:

temp/timer ]

Fauto m I

_med Ifitter

!o y reset

V ON-OFF A FAN SPEED steep

If the display reads "AS", a sensor has failed. Contact your

Authorized Frigidaire Service Center.

temp/timer ]

Fauto _

hi fitter

reed reset

V ON-OFF AFAN SPEED steep

If the display reads "ES", a sensor has failed. Contact your

Authorized Frigidaire Service Center.

Operating Instructions

(continued)

TO CHANGE TEMPERATURE DISPLAY:

temp/tfmer Fauto !

IW_lIl| _ him J

E_| _ reed I fitter

reset

V 0N=0FF A FAN SPEED

"/DO THIS:

PRESSAND HOLD THE

UP/DOWN BUTTONS

TOGETHER FOR 3 SECONDS

s[eep

YOU WILL SEE;

temp/timer auto !

C _ hi m l fi[ter

|meal I

lo J reset

V 0N=OFF A FAN SPEED s[eep

Note: The control is capable of displaying temperature in

degrees Fahrenheit or degrees Celsius.

TO TURN UNIT OFF:

temp/timer l

hi m

mecl

V 0N=OFF AFAN SPEED

fi[ter

reset

s[eep

DO THIS:

PRESS

ON/OFF BUTTON

YOU WILL SEE;

temp/dmer )

%0 fi[ter

reset

V 0N=OFF AFAN SPEED s[eep

ADDITIONAL THINGS YOU SHOULD KNOW

Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.

• The "Cool" circuit has an automatic 3minute time delayed start if the unit is turned off and on quickly.

This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue

to run during this time.

• There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having

to roll through to select another mode.

• The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.

• After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.

AUGER WHEELS

(8-WAY)

Air Directional Louvers

Air directional louvers control air flow direction. Your air conditioner has the louver

type described below.

Auger Type

The louvers will allow you to direct the air flow Up or Down and Left or Right

throughout the room as needed. Rotate the Auger Wheels until the desired

Left/Right direction is obtained. Pivot horizontal louvers until the desired

Up/Down direction is obtained.

Care and Cleaning

Air Filter

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug

the unit before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to see if cleaning is

necessary. Trapped particles in the filter can build up and cause an accumulation

of frost on the cooling coils.

•Open the front panel.

•Grasp the filter by the center and pull up and out.

•Wash the filter using liquid dishwashing detergent and warm water. Rinse filter

thoroughly. Gently shake excess water from the filter. Be sure filter is

thoroughly dry before replacing

•Or instead of washing, you may vacuum the filter clean.

NOTE; When replacing the air filter after cleaning, make sure the tabs on the air

filter are on the upper part of filter, and placed outward as shown in the drawing

on the left side.

Cabinet Cleaning

•Be sure to unplug the air conditioner to prevent shock or fire hazard. The

cabinet and front may be dusted with an oil-free cloth or washed with a cloth

dampened in a solution of warm water and mild liquid dishwashing detergent,

Rinse thoroughly and wipe dry.

•Never use harsh cleaners, wax or polish on the cabinet front.

•Be sure to wring excess water from the cloth before wiping around the controls.

Excess water in or around the controls may cause damage to the air conditioner.

.Plug in air conditioner.

Winter Storage

If you plan to store the air conditioner during the winter, remove it carefully from

the window according to the installation instructions. Cover it with plastic or return

it to the original carton.

Do not block air flow inside with blinds, curtains or furniture; or outside with

shrubs, enclosures, or other buildings,

The capacity of the room air conditioner must fit the room size for efficient and

satisfactory operation.

Install the room air conditioner on the shady side of your home. A window that faces

north is best because it is shaded most of the day.

Close the fireplace damper, floor and wall registers so cool air does not escape up

the chimney and into the duct work.

Keep blinds and drapes in other windows closed during the sunniest part of the day.

Clean the air filter as recommended in the section "Care and Cleaning".

Proper insulation and weather stripping in your home will help keep warm air out

and cool air in.

External house shading with trees, plants or awnings will help reduce the air

conditioner's work load.

Operate heat producing appliances such as ranges, washers, dryers and dishwashers

during the coolest part of the day.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Frigidaire Klimaanlage Handbücher

Frigidaire

Frigidaire CRA106HT1 Betriebsanleitung

Frigidaire

Frigidaire WAL128K2A2 Bedienungsanleitung

Frigidaire

Frigidaire FAS296P2A1 Bedienungsanleitung

Frigidaire

Frigidaire FRA103BT1 Bedienungsanleitung

Frigidaire

Frigidaire FRA065AT7 Bedienungsanleitung

Frigidaire

Frigidaire FHTE083WA1 Betriebsanleitung

Frigidaire

Frigidaire FAH086J1T1 Bedienungsanleitung

Frigidaire

Frigidaire FAC126P1 Bedienungsanleitung

Frigidaire

Frigidaire FRA053XT715 Betriebsanleitung

Frigidaire

Frigidaire FAH086M1T1 Bedienungsanleitung

Frigidaire

Frigidaire FAC083K7A5 Bedienungsanleitung

Frigidaire

Frigidaire 2020218A0678 Bedienungsanleitung

Frigidaire

Frigidaire FFPA1222R11 Betriebsanleitung

Frigidaire

Frigidaire FFRH1822R2 Betriebsanleitung

Frigidaire

Frigidaire FFRA0511Q19 Betriebsanleitung

Frigidaire

Frigidaire FRA296ST2 Bedienungsanleitung

Frigidaire

Frigidaire FAC053J7A2 Bedienungsanleitung

Frigidaire

Frigidaire FAC085J7A3 Bedienungsanleitung

Frigidaire

Frigidaire Home ComfortFRA08PZU1 Montageanleitung

Frigidaire

Frigidaire FRA103BT1 Bedienungsanleitung

Frigidaire

Frigidaire LRA11PZW114 Betriebsanleitung

Frigidaire

Frigidaire FAX052P7A Bedienungsanleitung

Frigidaire

Frigidaire CRA256ST211 Betriebsanleitung

Frigidaire

Frigidaire FAC055K7A4 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PUZ-SM100VKA Bedienungsanleitung

Airwell

Airwell Dakota DCI Series Bedienungsanleitung