Frigidaire FRS26W2AW1 Bedienungsanleitung

P/N 240389302 (0107)

Welcome & Congratulations

Congratulations on your purchase of a new refrigerator! We

here at Electrolux Home Products are very proud of our

product and we are completely committed to providing you

with the best service possible. Your satisfaction is our #1

priority.

Please read this Use & Care Manual very carefully. It contains

valuable information on how to properly maintain your new

refrigerator.

We know you’ll enjoy your new refrigerator and ThankYou

for choosing our product. We hope you consider us for future

purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating

instructions for your model. Use your refrigerator only as

instructed in this manual. These instructions are not meant

to cover every possible condition and situation that may

occur. Common sense and caution must be practiced when

installing, operating and maintaining any appliance.

Please record your model and serial numbers below for

future reference. This information is found on the serial

plate located inside the refrigerator compartment.

NOTE: Use only soap and water to clean serial plate.

Model Number:

Serial Number:

Purchase Date:

S erial Plate

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

Please attach sales receipt

here for future reference.

ExtendYour Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

• Total freedom from repair bills so

unexpected repairs won’t upset your

budget.

• Fast, convenient toll-free service is just

a phone call away.

• Top-quality repairs by factory-trained

experts.

• Quick access to genuine replacement

parts so you can rest assured your

refrigerator is repaired with the proper

components.

Please complete and mail in the Product

Registration Card included with your

refrigerator.

Important Safety Instructions

WARNING: Please Read All Instructions Before Using This Refrigerator.

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids

in the vicinity of this or any other appliance. Read

product labels for warnings regarding flammability and

other hazards.

• Do not operate the refrigerator in the presence of

explosive fumes.

• Avoid contact with any moving parts of automatic ice

maker.

• Remove all staples from the carton. Staples can cause

severe cuts, and also destroy finishes if they come in

contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior

wrapping material immediately after the refrigerator is

unpacked. Children should NEVER use these items to play.

Cartons covered with rugs, bedspreads, plastic sheets or

stretch wrap may become airtight chambers, and can quickly

cause suffocation.

These Guidelines Must Be Followed To Ensure That Safety Mechanisms In This Refrigerator

Will Operate Properly.

PROPER DISPOSAL OF YOUR REFRIGERATOR

OR FREEZER

Risk of child entrapment

Child entrapment and suffocation

are not problems of the past.

Junked or abandoned refrigerators

or freezers are still dangerous –

even if they will sit for “just a few

days.” If you are getting rid of your

old refrigerator or freezer, please

follow the instructions below to

help prevent accidents.

Before you throw away your old refrigerator/ freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb

inside.

• Have refrigerant removed by a qualified service

technician.

ELECTRICAL INFORMATION

•The refrigerator must be plugged into its own

dedicated 115 Volt, 60 Hz.,AC only electric outlet.

The power cord of the appliance is equipped with a

three-prong grounding plug for your protection against

electrical shock hazards. It must be plugged directly

into a properly grounded three-prong receptacle. The

receptacle must be installed in accordance with local

codes and ordinances. Consult a qualified electrician.

Do not use an extension cord or adapter plug.

• Immediately repair or replace any power cord that

becomes frayed or damaged.

• Never unplug the refrigerator by pulling on the power

cord. Always grip the plug firmly, and pull straight out

from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before

replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by

10% or more. Operating the refrigerator with insufficient

power can damage the compressor. Such damage is

not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall

switch or pull cord to prevent the refrigerator from being

turned off accidentally.

• Avoid connecting refrigerator to a Ground Fault Interruptor

(GFI) circuit.

NOTE:Turning the freezer temperature control to OFF

turns off the compressor, but does not disconnect

electrical power to the light bulb or other electrical

components.

This Owner’s Guide provides specific operating

instructions for your model. Use the refrigerator only as

instructed in this Use & Care Manual. Before starting the

refrigerator, follow these important first steps.

LOCATION

• Choose a place that is near a grounded electrical outlet.

Do Not use an extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat

sources.

• The refrigerator must be installed on a floor that is level

and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped

with an automatic ice maker.

INSTALLATION

•Do Not install the refrigerator where the temperature

will drop below 55°F (13°C) or rise above 110°F (43°C).

The compressor will not be able to maintain proper

temperatures inside the refrigerator.

Do Not block the toe grille on the

lower front of your refrigerator. Sufficient air

circulation is essential for the proper operation of

yourrefrigerator.

InstallationClearances

• Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical

connections:

Sides & Top --------------- 3/8”

Back ------------------------ 1”

DOOR OPENING

NOTE: If you refrigerator is placed with the door hinge

side against a wall, you may have to allow additional

space so the door can be opened wider.

Your refrigerator should be positioned to allow easy access

to a counter when removing food. For best use of drawers

and freezer baskets, the refrigerator should be in a

position where both the refrigerator and freezer doors can

be fully opened.

Installation

TOE GRILLE INSTALLATION / REMOVAL

To Remove Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Working from left side of toe grille, slip your fingers

between top of toe grille and cabinet. Gently pull

forward until first set of tabs are free. Slide your hand

down past the free tabs and pull forward again until the

second set of tabs are free. Continue this process until

all tabs are free and the toe grille can be removed. (See

graphic at top of page in right column.) 3. Check both doors to be sure seals touch cabinet on all

four sides.

LEVELING

All four corners of your refrigerator must rest firmly on a

solid floor. Your refrigerator is equipped with adjustable

front rollers to help level your unit.

To Level Your Refrigerator:

1. Remove toe grille. (See “To RemoveToe Grille”above.)

2. Use flat-blade screwdriver or 3/8” socket wrench

to adjust front rollers.

NOTE: The refrigerator doors are designed to shut by

themselves within a 20 degree opening.

To Install Toe Grille:

1. Open freezer and

fresh food

compartment doors.

2. Line up toe grille at

base of refrigerator,

making sure the four

bottom tabs are

resting through holes

at base of cabinet.

3. Starting from left side

of toe grille, press in on first top tab using your thumb

and push toe grille forward until it snaps in place. Continue

this process until all tabs aresnapped in place and toe

grille is secured to refrigerator.

Installation - Connecting Ice Maker To Water Supply

Toavoid electricshock,whichcancause deathor severepersonalinjury, disconnecttherefrigerator

from electrical power before connecting a water supply line to the refrigerator.

ToAvoid Property Damage:

•Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not

recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible

for any damage if plastic tubing is used for supply line.

• DO NOT install water supply tubing in areas where temperatures fall below freezing.

• Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft

water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6

meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)

ferrules/sleeves, and instructions for installing a water supply line.

Before Installing The Water Supply Line,You Will Need

•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

• Access to a household cold water line with water pressure between 20 and 100 psi.

• A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,

you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water

pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type

shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may

cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored

or have poor flavor. Discard ice made during the first 24 hours.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply

and flush supply line until water is clear. Turn OFF water supply at shut

off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line,

as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch).

Slide ferrule (sleeve) into valve inlet and finger tighten compression nut

onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of

refrigerator as shown.

7. Coil excess water supply line (about 2½ turns) behind refrigerator as shown

and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that

leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for

ON/OFF position of arm).

Door Removal Instructions

DOOR REMOVAL INSTRUCTIONS:

If it is necessary to move the refrigerator through narrow doorways,

follow these steps to remove the doors.

1. Disconnect electrical supply.

2. Open both doors, then remove toe grille.

3. Close doors.

To Remove Refrigerator Door:

1. Remove top hinge cover screw on refrigerator door and remove cover.

2. Trace around hinge with soft lead pencil. This will make it easier to

realign doors when they are replaced.

3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set

door aside.

4. Remove bottom hinge, if necessary.

5. Reverse this procedure to reinstall refrigerator door.

To Remove Freezer Door:

1. Disconnect water line coming from lower hinge of freezer door at connection

located under front of freezer: grip water tube firmly in one hand, then with

3/8” wrench or fingers, push in on gray collar to release water connector.

2. Remove top hinge cover screw on freezer door and remove cover.

3. Disconnect wiring harness connector plug at top hinge: place your thumbs

on flat sides of each connector and bend both parts back and forth,

then with firm grasp, pull both pieces apart.

4. Trace around hinge with soft lead pencil. This will make it easier to

realign doors when they are replaced.

5. Remove top hinge, allowing wiring harness to pull through hinge and lift freezer

door off of bottom hinge pin. Lay door down flat to avoid kinking water line.

6. Remove bottom hinge, if necessary.

7. Reverse this procedure to reinstall freezer door.

When both doors have been reinstalled, replace toe grille and plug in electrical

power cord. Turn both temperature controls to center position. Adjust settings

as necessary.

IMPORTANT: Before you begin, turn freezer temperature control to

OFF and remove electrical power cord from wall outlet. Remove any

food from door shelves.

Features At A Glance

Features may vary according to model

Temperature Controls

COOL DOWN PERIOD

To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading

it with food.

REFRIGERATOR & FREEZER CONTROLS

NOTE: When first turning refrigerator on, move refrigerator cold control to which is the recommended initial setting.

After 24 hours, adjust the controls as needed.

TEMPERATURE ADJUSTMENT

• After 24 hours, adjust the controls as needed. Adjust

temperatures gradually: move the knob in small

increments, allowing the temperature to stabilize.

• For colder temperatures, turn the knob towards Colder.

• For warmer temperatures, turn the knob towards Warmer.

To maintain temperatures, a fan circulates air in the

refrigerator and freezer compartments. For good circulation,

do not block cold air vents with food items.

IMPORTANT: Turning the freezer temperature control to “Off” turns off the compressor, but does not disconnect the

power to the light bulb and other electrical components.

EDIUGTNEMTSUJDAERUTAREPMET

mraWooTsItnemtrapmoCrotaregirfeRfI sdrawoTylthgilSlortnoCrotaregirfeRnruT redloC .

dloCooTsItnemtrapmoCrotaregirfeRfI sdrawoTylthgilSlortnoCrotaregirfeRnruT remraW .

mraWooTsItnemtrapmoCrezeerFfI sdrawoTylthgilSlortnoCrezeerFnruT redloC .

dloCooTsItnemtrapmoCrezeerFfI sdrawoTylthgilSlortnoCrezeerFnruT remraW .

ffOrotaregirfeRnruToT oTlortnoCrezeerFnruT ffO .

Refrigerator & Freezer Controls

▼

Looking Inside

Pizza Shelf

Ice Cream Shelf

PIZZA SHELF (SOME MODELS)

This shelf is attached to the freezer wall beside the ice dispenser container.

This convenient area allows for storage of pizza and other tall items placed

vertically between the ice dispenser container and the freezer wall.

ICE CREAM SHELF (SOME MODELS)

This shelf attaches to the top of the ice dispenser container. It allows storage

of both round and rectangular cartons of your favorite ice cream.

TIP-UP SHELF (SOME MODELS)

A Tip-Up shelf in the freezer section allows tall items to be easily stored.

To avoid personal injury or property damage, handle

tempered glass shelves carefully. Shelves may break suddenly if

nicked, scratched, or exposed to sudden temperature change.

Cantilever Sliding Glass Shelf

Cantilever Glass Shelf

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual needs. Before

adjusting the shelves, remove all food. Cantilever shelves are supported at

the back of the refrigerator.

To adjust cantilever shelves:

1Lift front edge up.

2 Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into the wall

bracket. Lower the shelf into the desired slots and lock into position.

SpillSafeTM glass shelves (some models) catch and hold accidental spills. In

some models, the SpillSafeTM shelves slide out for easy access to food and

for fast cleaning. The shelves slide out independently of their mounting brackets.

Just pull the front of the shelf forward. Shelves can be extended as far as the

stopper will allow but are notremovable from their mounting brackets.

Looking Inside (continued)

DOOR STORAGE

Door bins and shelves are provided for convenient storage

of jars, bottles, and cans. Frequently used items can be

quickly selected.

Some models have door bins that can accommodate gallon-

sized plastic drink containers and economy-sized jars and

containers. Some bins are adjustable for maximum storage

capacity.

The dairy compartment, which is warmer than the general

food storage section, is intended for short term storage of

cheese, spreads, or butter.

Fixed Door Bin

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved

to suit individual needs.

To move door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until locked in place.

Adjustable Door Bin

TALL BOTTLE RETAINER (SOME MODELS)

The Tall Bottle Retainer keeps tall containers in the bin from

falling forward when opening or closing the refrigerator door.

To install, hold the retainer at the top, and slide it over the

outside wall of the bin, as shown in the diagram. The Tall

Bottle Retainer works best with a Bin Snugger.

Tall Bottle Retainer (left) and Bin Snugger (right)

SPECIAL ITEM RACK (SOME MODELS)

The innovative design of the Special Item Rack allows you

to store a six-pack of 12 ounce drink cans, a bottle of wine,

a two-liter soft drink bottle, or a carton of eggs. The Special

Item Rack mounts on the left side of your refrigerator. To

install, just slide the Special Item Rack onto any shelf as

shown in the drawing.

Special ItemRack

Inhaltsverzeichnis

Andere Frigidaire Kühlschrank Handbücher

Frigidaire

Frigidaire FRS26ZSHW5 Bedienungsanleitung

Frigidaire

Frigidaire FSC23F7DS Bedienungsanleitung

Frigidaire

Frigidaire Refrigarator Betriebsanleitung

Frigidaire

Frigidaire FRT21C5A Bedienungsanleitung

Frigidaire

Frigidaire FRT21GNH Bedienungsanleitung

Frigidaire

Frigidaire FRS26ZRG Bedienungsanleitung

Frigidaire

Frigidaire FRT21HC5J Bedienungsanleitung

Frigidaire

Frigidaire FFHS2612LS Montageanleitung

Frigidaire

Frigidaire FFHT2142LK Bedienungsanleitung

Frigidaire

Frigidaire FGUN2642LF0 Betriebsanleitung

Frigidaire

Frigidaire FPE-16TA Bedienungsanleitung

Frigidaire

Frigidaire FPHS2387K F Bedienungsanleitung

Frigidaire

Frigidaire FRS6L9EFSS4 Service Benutzerhandbuch

Frigidaire

Frigidaire FRT18FR7E Bedienungsanleitung

Frigidaire

Frigidaire FFWC35F4LB Bedienungsanleitung

Frigidaire

Frigidaire FRT21FS5A Bedienungsanleitung

Frigidaire

Frigidaire FRT14G4B Bedienungsanleitung

Frigidaire

Frigidaire FRT17B1B Bedienungsanleitung

Frigidaire

Frigidaire FGHN2844LE Bedienungsanleitung

Frigidaire

Frigidaire FRT17IG5AT1 Bedienungsanleitung

Frigidaire

Frigidaire FRT17G5JS Bedienungsanleitung

Frigidaire

Frigidaire PLHS237ZD Bedienungsanleitung

Frigidaire

Frigidaire FRT18S6A Bedienungsanleitung

Frigidaire

Frigidaire FRS6B6E Benutzerhandbuch

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung