Frigidaire FRTX18N5BW0 Bedienungsanleitung

P/N 240400105 (0108)

Welcome & Congratulations

Congratulations on your purchase of a new refrigerator! We

here at Electrolux Home Products are very proud of our

product and we are completly committed to providing you

with the best service possible. Your satisfaction is our #1

priority.

Please read this Use & Care Manual very carefully. It contains

valuable information on how to properly maintain your new

refrigerator.

We know you’ll enjoy your new refrigerator and Thank You

for choosing our product. We hope you consider us for future

purchases.

PLEASE READ AND SAVE THESE INSTRUCTIONS

This Use & Care Manual provides specific operating

instructions for your model. Use your refrigerator only as

instructed in this manual. These instructions are not meant

to cover every possible condition and situation that may

occur. Common sense and caution must be practiced when

installing, operating and maintaining any appliance.

Please record your model and serial numbers below for

future reference. This information is found on your serial

plate located inside the refrigerator compartment.

NOTE: Use only soap and water to clean serial plate.

Model Number:

Serial Number:

Purchase Date:

Questions?

1-800-944-9044

(United States)

1-866-213-9397

(Canada)

Please complete and mail in the Product

Registration Card included with your

refrigerator.

Please attach sales receipt

here for future reference.

Extend Your Warranty Protection

With An

Extended Service Contract

CALL 1-800-944-9044

To Enjoy These Benefits:

• Total freedom from repair bills so

unexpected repairs won’t upset your

budget.

• Fast, convenient toll-free service is just

a phone call away.

• Top-quality repairs by factory-trained

experts.

• Quick access to genuine replacement

parts so you can rest assured your

refrigerator is repaired with the proper

components.

Important Safety Instructions

WARNING: Please Read All Instructions Before Using This Refrigerator.

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids

in the vicinity of this or any other appliance. Read pro-

duct labels for warnings regarding flammability and other

hazards.

• Do not operate the refrigerator in the presense of

explosive fumes.

• Avoid contact with any moving parts of automatic ice

maker.

• Remove all stables from the carton. Staples can cause

severe cuts, and also destroy finishes if they come in

contact with other appliances or furniture.

CHILD SAFETY

Destroy or recycle the carton, plastic bags, and any exterior

wrapping material immediately after the refrigerator is

unpacked. Children should NEVER use these items to play.

Cartons covered with rugs, bedspreads, plastic sheets or

stretch wrap may become airtight chambers, and can quickly

cause suffocation.

These Guidelines Must Be Followed To Ensure That Safety Mechanisms In This Refrigerator

Will Operate Properly.

PROPER DISPOSAL OF YOUR REFRIGERATOR

OR FREEZER

Risk of child entrapment

Child entrapment and

suffocation are not problems of

the past. Junked or abondoned

refrigerators or freezers are still

dangerous – even if they will sit

for “just a few days.” If you are

getting rid of your old refrigerator

or freezer, please follow the

instructions below to help

prevent accidents.

Before you throw away your old refrigerator/ freezer:

• Remove doors.

• Leave shelves in place so children may not easily climb

inside.

• Have refrigerant removed by a qualified service

technician.

ELECTRICAL INFORMATION

•The refrigerator must be plugged into its own

dedicated 115 Volt, 60 Hz., AC only electric outlet.

The power cord of the appliance is equipped with a

three-prong grounding plug for your protection against

electrical shock hazards. It must be plugged directly

into a properly grounded three-prong receptacle. The

receptacle must be installed in accordance with local

codes and ordinances. Consult a qualified electrician.

Do not use an extension cord or adapter plug.

• Immediately repair or replace any power cord that

becomes frayed or damaged.

• Never unplug the refrigerator by pulling on the power

cord. Always grip the plug firmly, and pull straight out

from the receptacle to prevent damaging the power cord.

• Unplug the refrigerator before cleaning and before

replacing a light bulb to avoid electrical shock.

• Performance may be affected if the voltage varies by

10% or more. Operating the refrigerator with insufficient

power can damage the compressor. Such damage is

not covered under your warranty.

• Do not plug the unit into an outlet controlled by a wall

switch or pull cord to prevent the refrigerator from being

turned off accidentally.

• Avoid connecting refrigerator to a Ground Fault

Interruptor (GFI) circuit.

NOTE: Turning the refrigerator temperature control to “0”

turns off the compressor, but does not disconnect

electrical power to the light bulb or other electrical

components.

This Use & Care Manual provides specific operating

instructions for your model. Use the refrigerator only as

instructed in this Use & Care Manual. Before starting the

refrigerator, follow these important first steps.

LOCATION

• Choose a place that is near a grounded electrical outlet.

Do Not use an extension cord or an adapter plug.

• If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat

sources.

• The refrigerator must be installed on a floor that is level

and strong enough to support a fully loaded refrigerator.

• Consider water supply availability for models equipped

with an automatic ice maker.

INSTALLATION

•Do Not install the refrigerator where the temperature

will drop below 55°F (13°C) or rise above 110°F (43°C).

The compressor will not be able to maintain proper

temperatures inside the refrigerator.

Do Not block the toe grille on the

lower front of your refrigerator. Sufficient air

circulation is essential for the proper operation of

your refrigerator.

InstallationClearances

• Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical

connections:

Sides & Top --------------- 3/8”

Back ------------------------ 1”

NOTE: If you see black coils/tubing on the back of your

refrigerator (air-cooled condenser) leave 3” clearance at

top of refrigerator.

DOOR OPENING

NOTE: If your refrigerator is placed with the door hinge

side against a wall, you may have to allow additional

space so the door can be opened wider.

Your refrigerator should be positioned to allow easy access

to a counter when removing food. To make this possible, the

direction in which the doors open can be reversed. See Door

Removal&ReversalInstructionson page 6.

Installation

LEVELING

All four corners of your refrigerator must rest firmly on a

solid floor. Your refrigerator is equipped with adjustable front

rollers to help level your unit.

To LevelYourRefrigerator:

1. Remove toe grille.

2. Use flat-blade screwdriver or 3/8” socket wrench

to adjust front rollers.

NOTE: Raise the front of the refrigerator enough so the

doors close freely when opened halfway. The refrigerator

should slope ¼” to ½” from front-to-back. Then level the

refrigerator from side to side.

Installation - Connecting Optional Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe personal injury, disconnect the

refrigerator from electrical power before connecting a water supply line to the refrigerator.

To Avoid Property Damage:

•Copper tubing is recommended for the water supply line. Water supply tubing made of ¼” plastic is not

recommended since it greatly increases the potential for water leaks. Manufacturer will not be responsible for

any damage if plastic tubing is used for supply line.

• DO NOT install water supply tubing in areas where temperatures fall below freezing.

•Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft

water, ensure that the softener is maintained and working properly.

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.

NOTE: Water line kit number 5303917950, available from your appliance dealer at additional cost, contains 25 feet (7.6

meters) of ¼ inch OD copper tubing, a saddle type shutoff valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)

ferrules/sleeves, and instructions for installing a water supply line.

Before Installing The Water Supply Line,You Will Need

•Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver

• Access to a household cold water line with water pressure between 20 and 120 psi.

• A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,

you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water

pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

• A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type

shutoff valve.

• A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.

IMPORTANT: It takes approximately 24 hours for the ice maker to begin producing ice. Air in new plumbing lines may

cause ice maker to cycle two or three times before making a full tray of ice. New plumbing may cause ice to be discolored

or have poor flavor. Discard ice made during the first 24 hours.

To Connect Water Supply Line To Ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply

and flush supply line until water is clear. Turn OFF water supply at shut

off valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line,

as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch).

Slide ferrule (sleeve) into valve inlet and finger tighten compression nut

onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of

refrigerator as shown.

7. Coil excess water supply line (about 2½ turns) behind refrigerator as shown

and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that

leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/

OFF position of arm).

Door Removal and Reversal Instructions

NOTE: If you have stainless steel doors -- go to the RemovingStainless

Steel Doorsand Handles Section on page 9.

NOTE: The direction in which your refrigerator doors open (door swing)

can be reversed, from left to right or right to left, by moving the door

hinges from one side to the other. Reversing the door swing should be

performed by a qualified person.

IMPORTANT: Before you begin, turn the refrigerator temperature control

to “0” and remove the electrical power cord from the wall outlet. Remove

any food from door shelves.

1. Remove toe grille and top hinge cover.

2. Remove top hinge with 3/8” hex driver and lift freezer door off of

center hinge pin. Set door aside.

3. Unscrew center hinge pin using adjustable wrench and save for

reassembly. Ensure plastic washer stays on hinge pin.

4. Lift refrigerator door off of bottom hinge and set aside.

5. Remove center hinge and shim by removing inside screw and

loosening two outside screws enough to allow hinge and shim to

slide out. Tighten screws.

6. Loosen two outside screws on opposite side of refrigerator, remove

inside screw and install center hinge.

7. Remove bottom hinge with 3/8” hex driver. Reinsert two outside screws

in holes and tighten. Inside screw will go to opposite side in step 8.

8. Remove two outside screws on opposite side of refrigerator and install

bottom hinge. Insert and tighten screw saved from step 7.

9. Unscrew bottom hinge pin using adjustable wrench. Move hinge pin

to other hole in hinge and tighten with adjustable wrench.

10. Reverse door handles (see instructions on next page).

11. Move freezer and refrigerator door stops to opposite side. Before

starting screws, use an awl to puncture the foam.

12. Position refrigerator door onto bottom hinge pin and screw center

hinge pin through center hinge into top of door. Close refrigerator door

to help align hinge hole.

13. Tighten center hinge pin with adjustable wrench.

14. Remove cabinet and hinge hole plugs and move to opposite side.

15. Lower freezer door onto center hinge pin.

16. Close freezer door. Have an assistant lift up on opposite side of door

while tightening screws to install top hinge.

17. Replace toe grille and top hinge cover.

18. Plug in electrical power cord and turn refrigerator temperature control

to center position. Adjust setting as necessary.

DOOR REMOVAL AND REVERSAL INSTRUCTIONS:

Door Removal and Reversal Instructions (continued)

NOTE: Some models have “pocket” handles, which are recessed into the sides of the door. On these models, only the

hinges will need to be reversed.

TO REMOVE FREEZER HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to bottom of freezer door.

2. Remove short trim piece by sliding trim straight up and off of handle

bracket.

3. Remove screw attaching top of handle to door.

4. Magnetic Nameplate Models: Gently pry magnetic nameplate frame from

door. Remove nameplate from its frame, turn frame upside down and

install in old handle holes. Insert magnetic nameplate into frame.

Self-Adhesive Nameplate Models: Gently peel off nameplate from door

and reapply over old handle holes.

TO ATTACH FREEZER HANDLE:

1. Reinstall handle on opposite side, using same hole as nameplate.

2. Attach handle to bottom of door.

3. Slide trim piece straight down onto handle bracket.

TO REMOVE FREEZER HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to bottom of freezer door.

2. Swing bottom of handle away from the door and slide handle straight up

and off of dovetail button.

3. Remove screw and dovetail button and install on other side, using the

same holes as nameplate.

4. Magnetic Nameplate Models: Use putty knife to gently pry magnetic

nameplate frame from door. Remove nameplate from its frame, turn frame

upside down and install in old handle holes. Insert magnetic nameplate

into frame.

Self-Adhesive Nameplate Models: Use putty knife to gently peel off name

plate from door and reapply over old handle holes.

TO ATTACH FREEZER HANDLE:

1. Start with handle offset away from door. Place top of handle over dovetail

button, swing handle into an upright position and pull downward, locking it

into place.

2. Secure bottom of handle with two screws removed earlier.

TO REMOVE FREEZER HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to bottom of freezer door.

2. Remove button plug using edge of putty knife.

3. Remove screw on side of freezer door and remove handle.

TO ATTACH FREEZER HANDLE:

1. Secure side of handle to door and replace button plug.

2. Secure handle to bottom of door.

NOTE: To remove freezer handle, refer to figure 3 on page 9.

Door Removal and Reversal Instructions (continued)

TRIM REMOVAL (FULL-LENGTH TRIM MODELS ONLY)

In some models, the refrigerator door has a full length trim piece which

continues from the bottom of the handle to the bottom of the door. The top

of the trim attaches to the handle bracket (Figure 1) or fits around the base

of the handle (Figure 2). An adhesive “trim lock” is positioned about halfway

down. The bottom of the trim is held in place by either an adhesive trim lock,

or a trim lock with two prongs inserted into a hole on the face of the door.

TO REMOVE TRIM:

1. Remove trim by gently pulling trim lock areas out and away from door.

2. When trim is free from door, slide the trim straight down and away

from base of handle.

NOTE: For models with short handle trim, remove by sliding trim straight

down and off of handle bracket.

TO REMOVE REFRIGERATOR HANDLE:

(Handles may be easier to reverse while doors are off.)

Figure 1 Style Handles

1. Remove two screws attaching handle to top of refrigerator door.

2. Remove screw attaching bottom of handle to door.

3. Remove two hole plugs and hinge pin plug on top of door and install

on opposite side. Use Phillips head screwdriver to remove plastic

screw plug from front of door and install on opposite side

Figure 2 Style Handles

1. Remove two screws attaching handle to top of refrigerator door.

2. Swing top of handle away from door and slide handle down and off of

dovetail button.

3. Remove screw and dovetail button and install on other side, moving

hole plugs from corresponding holes to opposite side.

TO ATTACH REFRIGERATOR HANDLE:

Figure 1 Style Handles

1. Secure bottom of handle with screws.

2. Secure top of handle with screws.

Figure 2 Style Handles

1. Start with handle offset away from door. Place bottom of handle over

dovetail button, swing handle into an upright position and pull upward,

locking it into place.

2. Secure top of handle with screws.

TO ATTACH TRIM:

1. Slide both trim locks out of trim.

2. Insert new adhesive trim locks contained in your literature pack.

NOTE: Trim lock must be removed and installed by sliding over the

two donut shaped areas.

3. Install trim to handle by sliding under base of handle. Carefully align

trim and press down at trim lock locations.

4. Use rubbing alcohol to remove any adhesive residue from old trim

lock locations.

Figure 1

Figure 2

Door Removal and Reversal Instructions (continued)

TO REMOVE REFRIGERATOR HANDLE:

(Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to top of refrigerator door.

2. Remove button plug using edge of putty knife.

3. Remove screw on side of refrigerator door and remove handle.

4. Reverse freezer and refrigerator handles as shown in figure 3.

TO ATTACH REFRIGERATOR HANDLE:

1. Secure side of handle to door and replace plug button.

2. Secure handle to top of door.

REMOVING STAINLESS STEEL DOORS AND HANDLES

Use care when using tools near surface of stainless steel doors to avoid scratching.

To Remove Doors

Stainless steel doors are not reversible. Follow these steps to remove doors.

1. Remove toe grille and top hinge cover.

2. Remove top hinge and lift freezer door off of center hinge pin. Set door

aside.

3. Unscrew center hinge pin using adjustable wrench and save for

reassembly. Ensure plastic washer stays on hinge pin.

4. Lift refrigerator door off of bottom hinge and set aside.

5. Remove center hinge and shim by removing inside screw and loosening

two outside screws enough to allow hinge to slide out.

6. Remove bottom hinge. Reinsert two outside screws in holes and tighten.

7. Reverse steps 1 - 6 to reinstall doors

To Remove Handles

1. Firmly hold freezer handle while loosening set screws with 3/32” allen

wrench. Remove freezer handle.

2. Repeat step 1 for refrigerator door.

Figure 3 - Handle Reversal

Refrigerator Door Without Trim

Typical Handle

Features At A Glance

Features may vary according to model

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Frigidaire Kühlschrank Handbücher

Frigidaire

Frigidaire FRT21P5A Bedienungsanleitung

Frigidaire

Frigidaire FRT18KD3AW0 Bedienungsanleitung

Frigidaire

Frigidaire FPE-26VWC Bedienungsanleitung

Frigidaire

Frigidaire FRT21S6AW7 Benutzerhandbuch

Frigidaire

Frigidaire FRT18P6C Bedienungsanleitung

Frigidaire

Frigidaire GLHS39EHPB - 23CF SXS ELEC 2-FILTR 7PAD I&W Benutzerhandbuch

Frigidaire

Frigidaire GLHS280ZA Bedienungsanleitung

Frigidaire

Frigidaire FPE-22VWA Bedienungsanleitung

Frigidaire

Frigidaire FFHT2117L W Bedienungsanleitung

Frigidaire

Frigidaire R134a Benutzerhandbuch

Frigidaire

Frigidaire FRS26HR4D Bedienungsanleitung

Frigidaire

Frigidaire Gallery FGHS2332L Bedienungsanleitung

Frigidaire

Frigidaire FRS23H5DS Bedienungsanleitung

Frigidaire

Frigidaire FRS23KF6C Bedienungsanleitung

Frigidaire

Frigidaire FRS26ZRG Bedienungsanleitung

Frigidaire

Frigidaire EFR492-B-6COM Bedienungsanleitung

Frigidaire

Frigidaire FFSC2323TS Bedienungsanleitung

Frigidaire

Frigidaire FRS6L9EFS Bedienungsanleitung

Frigidaire

Frigidaire FRS26ZNJS Bedienungsanleitung

Frigidaire

Frigidaire FRS26ZRGW9 Bedienungsanleitung

Frigidaire

Frigidaire FPUS2698LF Montageanleitung

Frigidaire

Frigidaire FRS3HF6JSB - 22.6 cu. Ft. Refrigerator Benutzerhandbuch

Frigidaire

Frigidaire FRS26W2A Bedienungsanleitung

Frigidaire

Frigidaire Gallery GLHT188WH Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung