Frigidaire FFLG2022MW0 Bedienungsanleitung

Unpacking laundry center .................................... 13

Installation Instructions .................................. 14-19

FCONTENTS

A_essodes ............................................. 20

........................................!i!!iiii!ili..........

F_n_ais

Espa_ol ..................................................41

For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent

property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

& WARNING - RISK OF FIRE

Read all of the following instructions before installing and using this appliance:

- Destroy the carton and plastic bags after the laundry center is unpacked. Children might use them for play. Cartons

covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all mate-

rials in a garbage container or make materials inaccessible to children.

- Clothes dryer installation and service must be performed by a qualified installer, service agency or the gas supplier.

- Install the appliance according to the manufacturer's instructions and local codes.

- The electrical service to the appliance must conform with local codes and ordinances and the latest edition of the

National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1.

- The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National

Fuel Gas Code ANSI Z223.1, or in Canada, CAN/ACG B149.1-2000. An individual manual shut-off valve must be

installed within 6 ft (1.83 m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

- The laundry center is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for

HOME USEonly. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.

- Do not install a clothes dryer with flexible plastic or flexible foil venting material. Flexible venting materials are

known to collapse, be easily crushed and trap lint. These conditions will obstruct clothes dryer airflow and increase

the risk of fire.

- The instructions in this manual and all other literature included with this appliance are not meant to cover every

possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing,

operating and maintaining any appliance.

WHAT TO DO IF YOU SMELL GAS:

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in

your building.

- Clear the room, building or area of all occupants.

- Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

- If you cannot reach your gas supplier, call the fire department.

EXCESSIVE WEIGHT HAZARD

To avoid back or other injury, have more than

one person move or lift the appliance.

Save these instructions for

futu re reference,

Pre-Installation Requirements

Tools and materials needed for installation:

- Adjustable pliers

- Phillips, straight, & square bit

screwd rivers

- Adjustable wrench

- Pipe wrench for gas supply (gas

dryer)

- LP-resistant thread tape (for natu-

ral gas or LP supply, gas dryer)

- Carpenter's level

- External vent hood

- 4-inch (102 mm), rigid metal or

semi-rigid metal exhaust duct work

- 3-wire or 4-wire 240 volt cord kit

(electric dryer)

- 4 in. (10.2 cm) clamp

- Gas line shutoff valve (gas dryer)

- 1/2NPT union flare adapters (x2)

and flexible gas supply line (gas

dryer)

- Metal foil tape (not duct tape)

Pleasereadallinstructionsbeforeusingthis

appliance.

Recognize safety symbols, words and

labels

Safety items throughout this manual are labeled

with a WARNING or CAUTION based on the risk

type as described below:

Definitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in

minor or moderate injury.

IMPORTANT indicates installation, operation or

maintenance information which is important but

not hazard-related.

Shipping Hardware

1::3 Foam shipping restraint (inside wash tub) removed and

stored

1:3 Shipping bolt (underneath appliance) removed and stored

Leveling

1::3 Laundry Center is level, side-to-side and front-to-back

I:3 Cabinet is setting solid on all corners

Water Supply

1:3 Rubber washers (shipped in tub) are installed in NEW inlet

hoses (shipped in tub)

1:3 HOT supply is connected to HOT inlet and COLD supply is

connected to COLD inlet

1:3 HOT and COLD water supply turned on

1:3 No leaks present at water supply connections or appliance

inlet connections - recheck in 24 hours

Drain

1:3 Stand pipe or wall drain height minimum 33"

1:3 Drain hose secured in place with cable tie (shipped in

drum)

Exhaust Venting

1:3 Free-flowing, clear of lint buildup

1:3 4 inch (102 mm) rigid or semi-rigid ducting of minimal

length and turns

1:3 NO foil or plastic venting material

1:3 Approved vent hood exhausted to outdoors

Gas Supply (Gas Dryer)

1:3 Manual shutoff valve present in supply

1:3 All connections sealed with approved sealer and wrench

tight

1:3 Conversion kit for LP system

1:3 Gas supply turned on

1:3 No leaks present at all connections -

check with soapy water, NEVER check with flame

240v Electric Supply (Electric Dryer)

1:3 Approved NEMA 10-30R or 14-30R service cord with all

screws tight on terminal block

1:3 Approved strain relief installed

1:3 Terminal access cover installed before initial operation

Electrical Power

1:3 House power turned on

1:3 Laundry Center plugged in

Final Checks

DInstallation Instructions and Use and Care Guide

read thoroughly

1:3 Water enters drum when cycle starts with lid lowered.

Dryer door latches and drum tumbles when cycle starts.

1:3 Registration card sent in

Electrical requirements for Laundry Center with electric dryer

CIRCUIT -Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers.

POWER SUPPLY- 3-wire or 4-wire, 240 volt, single phase, 60 Hz, Alternating Current.

This laundry center is internally grounded to neutral unless it was manufactured for sale in Canada.

Only a 4-conductor cord shall be used when the appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the neutral link is prohibited for: (1) new branch circuit

installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes do not permit grounding

OUTLET RECEPTACLE- NEMA 10-30R or NEMA 14-30R receptacle to be located so the power supply cord is accessible

when the dryer is in the installed position.

GROUNDING CONNECTION - See "Grounding requirements" in Electrical Installation section.

3-WIRE POWER SUPPLYCORD KIT (not supplied)

3-wire receptacle

(NEMA type 10-30R)

The dryer MUST employ a 3-conductor power

supply cord NEMA 10-30 type SRDT rated at 240

volt AC minimum, 30 amp, with 3 open end spade

lug connectors with upturned ends or closed

loop connectors and marked for use with clothes

dryers. For 3-wire cord connection instructions see

ELECTRICALCONNECTIONS FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLYCORD KIT (not supplied)

4-wire receptacle

(NEMA type 14-30R)

The dryer MUST employ a 4-conductor power supply

cord NEMA 14-30 type SRDT or ST (as required) rated

at 240 volt AC minimum, 30 amp, with 4 open end

spade lug connectors with upturned ends or closed

loop connectors and marked for use with clothes

dryers. For4-wire cord connection instructions see

ELECTRICAL CONNECTIONS FOR A 4-WIRE SYSTEM.

Laundry centers manufactured for sale in Canada have

factory-installed, 4-wire power supply cord (NEMA 14-

30R).

Electrical requirements for Laundry Center with gas dryer

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.

POWER SUPPLY- 2-wire, with ground, 120 volt, single

phase, 60 Hz, Alternating Current.

POWER SUPPLYCORD - The dryer is equipped with a 120

volt 3-wire power cord.

GROUNDING CONNECTION - See "Grounding

requirements" in Electrical Installation section.

Groundingtype

wallreceptacle f Do not, under

| any circumstances,

I]) I AI cut, remove,

_/ I_ or bypassthe

| _ grounding prong.

Powercord with

3-prong grounded plug

Gas supply requirements

EXPLOSION HAZARD

Uncoated copper tubing will corrode when subjected

to natural gas, causing gas leaks. Use ONLY black iron,

stainless steel, or plastic-coated brass piping for gas

1 Installation MUST conform with local codes, or in

the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1 (latest edition).

2The gas supply line should be 1/2 inch (1.27 cm)

pipe.

3 If codes allow, flexible metal tubing may be used

to connect your dryer to the gas supply line. The

tubing MUST be constructed of stainless steel or

plastic-coated brass.

4 The gas supply line MUST have an individual

shutoff valve installed in accordance with the

B149.1, Natural Gas and Propane Installation Code.

5A 1/8 inch (0.32 cm) N.RT. plugged tapping,

accessible for test gauge connection, MUST be

installed immediately upstream of the gas supply

connection to the dryer.

6 The dryer MUST be disconnected from the gas

supply piping system during any pressure testing

of the gas supply piping system at test pressures in

excess of 1/2 psig (3.45 kPa).

2 The dryer MUST be isolated from the gas supply

piping system during any pressure testing of the

gas supply piping system at test pressures equal to

or less than 1/2 psig (3.45 kPa).

8 Connections for the gas supply must comply with

the Standard for Connectors for Gas Appliances,

ANSI Z21.24.

Water supply requirements

Hot and cold water faucets MUST be installed within 42

inches (107 cm) of your washer's water inlet. The faucets

MUST be 3/4 inch (1.9 cm) with threading for laundry

hose connection. Water pressure MUST be between

10 psi (0.69 bars) and 120 psi (8.27 bars). Pressure

difference between hot and cold cannot be more than 10

psi. Your water department can advise you of your water

pressure.

Drain system requirements

:[ Drain capable of eliminating 17 gals (64.3 L) per minute.

2 A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.

3 The standpipe height above the floor should be:

Minimum height: 33 in. (84 cm)

Maximum height: 96 in. (244 cm)

96"

(244cm)

max, T

33"

(84cm)

rain.

i=1

Exhaust system requirements

vent hood which has a swing-out damper(s) that open when the dryer is in

operation. When the dryer stops, the dampers automatically close to prevent

drafts and the entrance of insects and rodents. To avoid restricting the outlet,

maintain a minimum of 12 inches (30.5 cm) clearance between the vent hood

and the ground or any other obstruction.

FIRE HAZARD

fire hazards. ....

The following are specific requirements for proper and safe opera-

tion of your dryer.

FIRE HAZARD

Do not install a clothes dryer with flexible plastic or metal foil venting

materials. Flexible venting materials are known to collapse, be easily

crushed and trap lint. These conditions will obstruct clothes dryer airflow

and increase the risk of fire.

:If your present system is made up of plastic duct or metal foil duct, replace it

with a rigid or semi-rigid metal duct. Also, ensure the present duct is free of

any lint prior to installing dryer duct. Incorrect

Exhaust system requirements, continued

FIRE HAZARD

Aclothes dryer must be exhausted outdoors. Do not

exhaust dryer into a chimney, a wall, a ceiling, an attic,

a crawl space or any concealed space of a building. A

clothes dryer produces combustible lint. If the dryer is

not exhausted outdoors, some fine lint will be expelled

into the laundry area. An accumulation of lint in any

area of the home can create a health and fire hazard.

The dryer must be connected to an exhaust outdoors.

Regularly inspect the outdoor exhaust opening and

remove any accumulation of lint around the outdoor

exhaust opening and in the surrounding area.

FIRE HAZARD

-Do not allow combustible materials (for example:

clothing, draperies/curtains, paper) to come in

contact with exhaust system. The dryer MUST NOT

be exhausted into a chimney, a wall, a ceiling,

or any concealed space of a building which can

ii accumulate lint, resulting in a fire hazard.

- Do not screen the exhaust ends of the vent system,

or use any screws, rivets or other fasteners that

extend into the duct to assemble the exhaust

system. Lint can become caught in the screen, on

the screws or rivets, clogging the duct work and

ii creating a fire hazard as well as increasing drying

ii times. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with metal foil duct

tape. All male duct pipe fittings MUST be installed

downstream with the flow of air.

FIRE HAZARD

Exceeding the length of duct pipe or number of elbows

allowed in the "MAXIMUM LENGTH" charts can cause

an accumulation of lint in the exhaust system. Plugging

the system could create a fire hazard, as well as

€-

O-

MAXIMUM LENGTH

of 4" (102 mm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

(10.2 cm) Iouvered

56 ft. (17 m)

2.5"

(6.35 cm)

42 ft. (13 m)

1 48 ft. (14.5 m) 34 ft. (10.5 m)

2 40 ft. (12 m) 26 ft. (8 m)

3 32 ft. (9.5 m) 18 ft. (5.5 m)

FIRE HAZARD

-Do not install flexible plastic or flexible foil venting

material.

- If installing semi-rigid venting, do not exceed 8 ft.

Exhaust system requirements, continued

Install male fittings in correct direction"

CORRECT iNCORRECT

In installations where the exhaust system is not described

in previous pages, the following method must be used to

determine if the exhaust system is acceptable:

1 Connect an inclined or digital manometer between

the dryer and the point the exhaust connects to the

dryer.

2 Set the dryer timer and temperature to air fluff and

start the dryer.

3 Read the measurement on the manometer.

4 The system back pressure MUST NOT be higher

than 0.75 inches of water column. [f the

system back pressure is less than 0.75 inches of

water column, the system is acceptable. [f the

manometer reading is higher than 0.75 inches of

water column, the system is too restrictive and the

installation is unacceptable.

Although vertical orientation of the exhaust system is

acceptable, certain extenuating circumstances could

affect the performance of the dryer:

o Only rigid metal duct work should be used.

Venting vertically through a roof may expose the

exhaust system to down drafts causing an increase

in vent restriction.

Running the exhaust system through an

uninsulated area may cause condensation and

faster accumulation of lint.

Compression or crimping of the exhaust system will

cause an increase in vent restriction.

The exhaust system should be inspected and

cleaned a minimum of every 18 months with

normal usage. The more the dryer is used, the

more often you should check the exhaust system

and vent hood for proper operation.

Exhaust direction

The laundry center may be exhausted four (4) ways with

rear flush installation:

1. Straight back

2. Down (8 inch [20.3 cm] length of 4 inch diameter

[102 mini rigid duct and 1 elbow down)

3. Left (8 inch [20.3 cm] length of 4 inch diameter [102

mini rigid duct, 1 elbow down and 1 elbow left)

4. Right (8 inch [20.3 cm] length of 4 inch diameter

[102 mm] rigid duct, 1 elbow down and 1 elbow

right)

To exhaust up, add an 11 inch (28 cm) length of standard

4 inch (102 mm) diameter duct and a 90 ° elbow. The

unit will be positioned about 4.5 inches (11.5 cm) away

from the wall (flush to wall exhausting may be done by

going below the dryer then sideways).

An exhaust hood positioned to line up with the dryer

exhaust can be installed directly through the outside wall.

To exhaust to the side or down, add an 8 inch (20.3 cm)

length of standard 4 inch (102 mm) diameter duct and a

90 ° elbow.

See also Clearance Requirements on the next page.

Manufactured or mobile home installation

1Installation MUST conform to current Manufactured

Home Construction & Safety Standard, Title 24

CFR, Part 32-80 (formerly the Federal Standard

for Mobile Home Construction and Safety, Title 24,

HUD Part 280) or Standard CAN/CSAZ240 MH.

2 Dryer MUST be exhausted outside (outdoors, not

beneath the mobile home) using metal ducting

that will not support combustion. Metal ducting

must be 4 inches (10.16 cm) in diameter with no

obstructions. Rigid metal duct is preferred.

3 If dryer is exhausted through the floor and area

beneath the mobile home is enclosed, the exhaust

system MUST terminate outside the enclosure with

the termination securely fastened to the mobile

home structure.

4 Refer to previous sections in this guide for other

important exhaust venting system requirements.

5When installing a gas dryer into a mobile home, a

provision must be made for outside make up air.

This provision is to be not less than twice the area

of the dryer exhaust outlet.

6Installer MUST anchor this laundry center to the

floor with approved Mobile Home Installation Kit -

P/N 137067200.

Clearance requirements

EXPLOSION HAZARD

Do not install the dryer where gasoline or other

flammables are kept or stored. If the dryer is installed

in a garage, it must be a minimum of 18 inches (45.7

cm) above the floor. Failure to do so can result in

DO NOT install your dryer in a closet with a solid door.

4 Closet door ventilation required: A minimum

of 120 square inches (774.2 cm2) of opening,

equally divided at the top and bottom of the

door, is required. Openings should be located 3

inches (7.6 cm) from bottom and top of door.

Openings are required to be unobstructed when a

door is installed. A Iouvered door with equivalent

air openings for the full length of the door is

acceptable.

DO NOT INSTALL YOUR LAUNDRY CENTER:

1In an area exposed to dripping water or outside

weather conditions. The ambient temperature

should never be below 60° F (15.6 ° C) to

maximize detergent effectiveness.

2In an area where it will come in contact with

curtains, drapes, or anything that will obstruct

the flow of combustion and ventilation air.

3 On carpet. Floor MUST be solid with a maximum

slope of 1 inch (2.5 cm). To minimize vibration

or movement, reinforcement of the floor may be

Installation in a Recess or Closet

1A dryer installed in a bedroom, bathroom, recess or

closet, MUST be exhausted outdoors.

2No other fue! burning appliance shall be installed in

the same closet as the gas dryer.

3 Your dryer needs the space around it for proper

ventilation.

(7.63cm)

closet door

60 sq. in.

(387.1 cm 2)

60 sq. in.

(387.1 cm 2)

Clearance requirements, continued

MINIMUM INSTALLATION CLEARANCES- Inches (cm)

Alco_ve SIDES REAR TOP FRONT

0"(0 cm) 0"(0 cm) 1" (2.5 cm) n/a

Closet _ O"(Ocm) O"(Ocm) 1" (2.5cm) 1" (2.5cm)

1" ----_, ,-_-- o"--_II-_--= io¢,T,) ,,,, i

- %T - m-

Laundry Center Dimensions

17.6"

(4S cm)

water supply

connection on

rear ofwasher 2

drain hose reten-

tion clamp on rear

of washer 2

D gas supply

pipe on rear of

gas unit

]

power cord

,_; attachment

L i location on

orear ofunib

'"i ", exhaust vent on

' 4 in, (102 mm)

i:: 12"

: i (30.5 cm)

1Powersupply cord length on gas unit approximately 60 inches (t52.5 cm).

2Hot and cold inlet hose length approximately 48 inches (122 cm),

3Loosedrain hose length beyond damp approximately 52 inches (132 cm).

76"

9.4" (193 cm)

(24 cm)

5.5"

(14 cm)

44"

(112 cm)

47.5" (120,5 cm)

54.75"

(139 cm)

37 l/

(94 cm)

"_ 31.5" (80 cm)

center line height

for 4 in. (102 mm)

exhaust outlet

42.5"

(108 cm)

Andere Handbücher für FFLG2022MW0

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Frigidaire Waschmaschine Trockner Handbücher

Frigidaire

Frigidaire GLGT1142FS0 Bedienungsanleitung

Frigidaire

Frigidaire Washer/Dryer Bedienungsanleitung

Frigidaire

Frigidaire GCEH1642FS4 Bedienungsanleitung

Frigidaire

Frigidaire GLGT1142CS0 Bedienungsanleitung

Frigidaire

Frigidaire Full Size Laundry Center Gas Bedienungsanleitung

Frigidaire

Frigidaire FFLG2022MW3 Bedienungsanleitung

Frigidaire

Frigidaire Laundry Center Bedienungsanleitung

Frigidaire

Frigidaire FFLG2022MW0 Betriebsanleitung

Frigidaire

Frigidaire GLET1041AS2 Bedienungsanleitung

Frigidaire

Frigidaire GLET1031C Bedienungsanleitung

Frigidaire

Frigidaire Laundry Center Bedienungsanleitung

Frigidaire

Frigidaire MLXE Bedienungsanleitung

Frigidaire

Frigidaire GLGT1142CS0 Bedienungsanleitung

Frigidaire

Frigidaire 134126300B Bedienungsanleitung

Frigidaire

Frigidaire FLEB8200DS0 Bedienungsanleitung

Frigidaire

Frigidaire GLGH1642DS1 Bedienungsanleitung

Frigidaire

Frigidaire FFLE2022MW1 Bedienungsanleitung

Frigidaire

Frigidaire GLGT1031F Bedienungsanleitung

Frigidaire

Frigidaire FFLE1011MW0 Bedienungsanleitung

Frigidaire

Frigidaire 27 Bedienungsanleitung

Frigidaire

Frigidaire CLCG900FW3 Bedienungsanleitung

Frigidaire

Frigidaire GLGT1142CS1 Bedienungsanleitung

Frigidaire

Frigidaire FGX831FS Benutzerhandbuch

Frigidaire

Frigidaire GCET1031FS4 Bedienungsanleitung

Beliebte Waschmaschine Trockner Handbücher anderer Marken

Whirlpool

Whirlpool WFC8090GX Bedienungsanleitung

Whirlpool

Whirlpool LTE5243DQ6 Bedienungsanleitung

Bosch

Bosch XQG100-WDU285H00W Bedienungsanleitung

Beko

Beko HTE10736XS Bedienungsanleitung

AEG

AEG L76685NWD Bedienungsanleitung

LG FWV1128WTSA Bedienungsanleitung

Electrolux

Electrolux WTSL 6 E201 Bedienungsanleitung

AEG

AEG OKO_LAVAMAT 1260 Bedienungsanleitung

Blomberg

Blomberg LRI285411 Bedienungsanleitung

Franke

Franke FWD 1400-6EI Bedienungsanleitung

Hitachi

Hitachi BD-W3300 Bedienungsanleitung

Whirlpool

Whirlpool FWDG96148SBS GCC Installations- und Betriebshandbuch

Equator

Equator EZ 1720 Bedienungsanleitung

NEFF

NEFF V6540X1EU Technisches Datenblatt

Dawlance

Dawlance Spinner DS 9000 CM Bedienungsanleitung

Hoover

Hoover WDYNS 654D-80 Bedienungsanleitung

Hotpoint

Hotpoint H3D91WBUK Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Kurzanleitung