Frontgate DAX POOL TABLE 165665 Bedienungsanleitung

DAX POOL TABLE

Item #165665

Assembly Instruction

Step 1: Attach the leg runner to the legs by using Bolt(R), Plug(W) and CROSS DOWEL (V)

NO NAME SIZE PCS DRAW

R BOLT Ø5/16"X4 1/2" 2

VCROSS DOWEL Ø5/16"XØ5/8" 2

WWOOD PLUG ∅21 X 10mm 2

1/7

NO NAME SIZE PCS DRAW

2Leg runner

Legs 2

39 1/4" x 6" x 26 5/8"

57 3/16" x 2" x 8"

DAX POOL TABLE

Item #165665

Assembly Instruction

Step 2: Attach the legs to the long beams by using Bolt(P),Washer(Q) and Nut(L)

NO NAME SIZE PCS DRAW

PBOLT

Ø3/8" x Ø3/4"

Ø3/8" X 4"

NUT

Q32

L∅3/8"

WASHER

2/7

NO NAME SIZE PCS DRAW

Long beams 2

390 3/4" x 1 3/8" x 3"

DAX POOL TABLE

Item #165665

Assembly Instruction

Step 3: Attach the legs to the short beams by using Bolt(P),Washer(Q) and Nut(L)

3/7

NO NAME SIZE PCS DRAW

PBOLT

Ø3/8" x Ø3/4"

Ø3/8" X 4"

NUT

Q16

L∅3/8"

WASHER

NO NAME SIZE PCS DRAW

Short beams 2

437 13/32" x 3 3/8" x 1 1/2"

Short beams 2

549" x 4" x 1 1/2"

NO NAME SIZE PCS DRAW

K∅1/4"X2-1/2"

SCREW 12

Step 4A: Locate the center piece of framed slate and

position it on the cross beam assembly so that it is

centered to both the length and width of the

assembly (you must be very accurate with

placement). Pre-drill a hole through the slate screw

hole using a 3/16” drill bit. Vacuum out debris and

secure using slate screws (K). Continue with same

process with both outside sections of slate.

Step 4B: With a level or straight edge, be sure that

the slate seams are flat and level. If adjustments

need to be made, loosen slate screws and place a

shim(s) in area that needs adjustment. Tighten

screws and check for levleness. Use Bee’s Wax or

similar to fuse the seams of the slate together.

Step 5: Remove any wax, dust and debris from the

slate surface to prep it for the bedcloth. Layout

bedcloth centering it over the slate surface. Starting

at one end, staple cloth to slate framing working

from center out toward the pockets stretch cloth

toward pockets. Go to opposite end of table and

repeat process but pull the cloth tight while stapling.

Repeat on long sides working from center between

center pocket and end pocket stretching cloth

toward the pockets as you staple. Once cloth is

completely stapled, cut pocket openings by cutting

small vertical incisions in cloth to relax the fabric so

it can be stretched and stapled around

opening. Finally, make “X” style slits in cloth where

rail bolts will go through the slate holes (see photo).

DAX POOL TABLE

Item #165665

Assembly Instruction

4/7

NO NAME SIZE PCS DRAW

∅5/16"

NUT

Step 6: Assemble the blinds completely using Dowel (A), Washer (I) and Bolt (J).

Step 7A: Assemble the end rails completely using Dowels (A), Washer (C), Nut (D)

and Threaded Rod (B).

Step 8: Attach the top rail assembly to the blind assembly using Screw (E) and Metal (F).

NO NAME SIZE PCS DRAW

BTHREADED ROD ∅5/16"X3"

∅10mmX30mm

DOWEL

CWASHER ∅5/16"X3/4"X2mm

8-7/8"X2-5/8"X1/8"

METAL

5-7/8"X1-1/2"X1-1/2"

METAL

∅1/4"X∅5/8"

WASHER

BOLT ∅1/4"X5/8"

BOTTOM VIEW Step 7A

DAX POOL TABLE

Item #165665

Assembly Instruction

Step 7B

Step 6 and Step 8

108

SCREW #8X1/2"

5" x 1" x 1"

METAL 18

5/7

XSCREW #8X3/4" 12

NO NAME SIZE PCS DRAW

Long blinds 2

Short blinds 2

755 3/8" x 3/4" x 6 3/4"

Short rails right 2

851 1/8" x 7 1/8" x 1 1/2"

Short rails 2

Short rails left

100 7/8" x 3/4" x 6 3/4"

51 1/8" x 7 1/8" x 1 1/2"

58 1/4" x 7 1/8" x 1 1/2"

Step 7B: Assemble the middle rails completely using Dowels (A), Metal (G) and Screw (X)

NO NAME SIZE PCS DRAW

DOME WASHER

∅3/8"

NUT

Step 9: Attach rail/blind assemblies to the slate using Dome Washer (M), Star Washer (N), Threaded Rod (O), and Nut (L).

STAR WASHER

THREADED ROD

∅3/8"

∅3/8"X3"

DAX POOL TABLE

Item #165665

Assembly Instruction 6/7

NO NAME SIZE PCS DRAW

Step 10: NOTE: the side pockets and corner pockets ARE different and will only work correctly one way. To install the pockets,

squeeze the top of the pocket and bring it up through the pocket opening from the bottom. Be sure not to push back the pockets

so they are flush against the rail; the first priority is to ensure they line up with the felt near the playing surface. Peel back the

paper to reveal the sticky side of the velcro on the backside of the Pocket to secure the Pocket to the Rail.

TCORNER POCKET

CENTER POCKET 2

DAX POOL TABLE

Item #165665

Assembly Instruction 7/7

Inhaltsverzeichnis

Andere Frontgate Spiel Handbücher

Frontgate

Frontgate 128705 Bedienungsanleitung

Beliebte Spiel Handbücher anderer Marken

Outdoor Play

Outdoor Play Box it! 2020 Bedienungsanleitung

Beleduc

Beleduc Papilio Bedienungsanleitung

Costway

Costway UY10001 Bedienungsanleitung

Vex

Vex Add It Up Bedienungsanleitung

DGT

DGT Centaur Bedienungsanleitung

Radica Games

Radica Games BUCKAROO 630 Bedienungsanleitung

Fundex Games

Fundex Games Timber Tumble Bedienungsanleitung

Go! Gater

Go! Gater 1-1-16453-TP02 Bedienungsanleitung

Smoby

Smoby BBF Challenger Bedienungsanleitung

Hathaway

Hathaway BG2019SK Bedienungsanleitung

Roberto Sport

Roberto Sport INGLESE Bedienungsanleitung

Beleduc

Beleduc XXL Witches' Kitchen Bedienungsanleitung

Koala Technologies

Koala Technologies KoalaWare Spider Eater Bedienungsanleitung

Tomy

Tomy The Magic Oven Bedienungsanleitung

Sega

Sega GAME SHOW Bedienungsanleitung

Tiger Electronics

Tiger Electronics Last Out 7-584-0 Bedienungsanleitung

Fisher-Price

Fisher-Price RollOverRover Bedienungsanleitung

Mattel

Mattel World Championship Football Bedienungsanleitung