FSP Technology EMERGY 1000 Bedienungsanleitung

EMERGY 1000

User Manual

Please read this User Manual first before Operating the System.

- 1 -

Table of Contents

1. ABOUT THIS MANUAL - 2 -

1.1 Additional Information - 2 -

1.2 Symbol Used - 2 -

2. PRODUCT OVERVIEW - 3 -

2.1 Appearance and Functions - 3 -

2.2 Gauge/Charging Indicators and Alarm - 4 -

3. SYSTEM OPERATIONS - 7 -

3.1 Turning On/Off System - 7 -

3.2 Charging System - 7 -

3.3 System Outputs - 9 -

3.4 Operating Modes - 9 -

3.5 Physical Positioning - 10 -

3.6 Apparatus/Equipment/Appliances - 10 -

4. TRANSPORTATION - 12 -

5. STORAGE - 13 -

6. IN CASE OF EMERGENCY - 14 -

7. MAINTENANCE - 14 -

8. WARRANTY - 15 -

- 2 -

1.About this Manual

This User Manual is for use with EMERGY 1000. User must refer to the User Manual before using

to avoid abnormal situations.

1.1 Additional Information

(1) The information in this document is subject to change without notice.

(2) Specification of the product can be changed without any notice to customers for the system

improvement.

written permission is prohibited, except as allowed under the copyright laws.

1.2 Symbol Used

Symbols

Meaning

Description

DANGER

Beware dangerous voltage.

WARNING

It calls attention to a procedure, practice, or the like,

which, if not correctly performed or adhered to, could

result in personal injury.

CAUTION

It calls attention to an operating procedure, or the

like, which, if not correctly performed or adhered to,

could result in damage to or destruction of part or

all of the products.

- 3 -

2.Product Overview

EMERGY 1000 is All-in-One Energy Storage System that integrate Li-Ion Battery System, Battery

Management System, AC charger, Photovoltaic (PV) charger, DC to AC inverter, System Control

into the compact & portable suitcase.

2.1 Appearance and Functions

Figure 1 illustrates the appearance and key external parts in EMERGY 1000 . The functions of

each key parts are highlighted in Table 1.

Figure 1(a). Top View

Figure 1(b). Rear View

- 4 -

Table 1. Key External Parts and Functions

Item

Name

Function

Notes

MSW (MAIN

CONTROL SW)

Switch ON/OFF the

system

Hard press MSW to toggle

system ON/OFF.

AC OUT SW

Switch ON/OFF AC output

Hard press AC OUT SW to

toggle AC output ON/OFF.

MODE

Select Standby or On-Line

Operating Mode

Typical transfer time for

Standby Mode is 16mS. No

transfer time (0mS) for On-Line

Mode.

AC OUT

AC output(s)

AC socket(s) varies with

country.

5V USB OUT

USB Power Sources

Total current rated at 2A.

GAUGE

INDICATOR

Display State Of Charge

(SOC) of Li-Ion batteries

(Please see Table 2)

CHARGING

INDICATOR

Indicate charging state of

the battery

With a lightening mark under

CHARGING INDICATOR.

(Please see Table 3)

SYSTEM

INDICATOR

System status indication

USB power outlet is synched

with system power.

Light up when power is present.

AC OUT

INDICATOR

AC output power

indication

Light up when power is present.

MODE

INDICATOR

Indicate operating mode

Light up for On-Line Mode.

Turn off for Standby Mode.

LIFT HANDLE

For Lifting EMERGY 1000.

PULL HANDLE

For pulling/ pushing the

system while on wheels.

Not for lifting EMERGY 1000.

AC INLET

AC Input connection

(Please see paragraph 3.2.1)

PV INLET

AC Input connection

(Please see paragraph 3.2.2)

HEAT SINK

For heat dissipation

Blockage of heat sink area may

impede system performance.

WHEELS

For carrying system along

flat or smooth surface.

Please see Figure 6 to know

the locking mechanisms are

provided in the two front

wheels.

DO NOT use PULL HANDLE, but LIFT HANDLE to lift up EMERGY 1000 to

avoid damage to the system.

2.2 Gauge/Charging Indicators and Alarm

- 5 -

2.2.1 Gauge Indicator

The State Of Charge (SOC) or remaining capacity of the battery is illustrated thru five (3 green, 1

orange, 1 red) LED indictors on its face panel. From right to left each additional indicator

corresponds to about 20% additional battery capacity as illustrated in Table 2.

Table 2. Gauge Indicators

Status

Meaning

5 LEDs On

(GGWOR)

SOC > 80%

4 LEDs On

(GGOR)

SOC between 60-80%

3 LEDs On

(GOR)

SOC between 40-60%

2 LEDs On

(OR)

SOC between 20-40%

1 LED On

(R)

SOC between 10-20%

(Charge Soon)

1 LED

blinking

(R)

SOC between 0-10%

(Charge Immediately)

All LEDs Off

MSW is off or battery fully drained.

F 3/4 H 1/4 E

- 6 -

2.2.2 Charging Indicator

CHARGING INDICATOR is used to indicate the stage of charging to the battery as illustrated in

Table 3.

Table 3. Charging Indicator

Status

Meaning

Stay On

Charging

Blinking

1. Close to fully charged.

2. Blinking happens if charging current is less

than 2A.

3. When closing to fully charged, it is normal

whether CHARGER INDICTOR is blinking or

not.

Off

Five GAUGE INDICATORs are all on and

CHARGING INDICATOR is off if the system is

fully charged.

2.2.3 Alarm

When the remaining battery capacity drops below 15%, an alarm sound- a periodical short buzz will

be initiated to inform user that the battery may run out of energies soon. It should be recharged as

soon as possible to avoid damage batteries.

- 7 -

3.System Operations

3.1 Turning On/Off System

To turn on the system, firmly press MSW (Main Control Switch) for a light click. SYSTEM

INDICATOR and GAUGE INDICATOR should light up after about 10 seconds delay. This delay is

normal and should not be alarmed.

To turn off the system, press MSW again. All indicating lights will be off. Slight delay in AC OUT

INDICATOR is normal when AC OUT is not or lightly loaded. Pressing MSW will toggle the system

status.

3.2 Charging System

3.2.1 AC Charging

To perform system charging via AC power source, the following steps are to be followed.

Step 1: Turn on the system by pressing MSW.

Step 2: Connect power cord (IEC320 type) to AC INLET, as illustrated in Figure 2.

Figure 2. AC charging

When EMERGY 1000 is charging, CHARGING INDICATOR will light up CHARGING INDICATOR

will turn off automatically when charging is terminated. The charging time for EMERGY 1000 is

around 2.5 hours for a full charge cycle (from empty to full).

The input source should comply with the input range (100-120Vac or

220-240Vac) as indicated on AC INLET.

- 8 -

3.2.2 PV Charging

To perform system charging via PV power source, the following steps are to be followed.

Step 1: Connect PV charging cable adaptor to PV INLET first, as illustrated in Figure 3.

Step 2: Connect MC4 connectors from the cable adaptor to MC4 connectors from PV panels.

Use Y Type MC4 connectors (not provided) for multiple PV panel branches.

Figure 3. PV charging

Step 3: Turn on the system by pressing MSW.

When EMERGY 1000 is charging by PV power, CHARGING INDICATOR will light up CHARGING

INDICATOR will turn off automatically when charging is terminated.

EMERGY 1000 would take about 3 hours for a full charger cycle (from empty to full) when PV

power is greater than 650Wp and it is optimal solar radiation.

Failure to connect the cable adaptor first may cause unexpected electrical

shock from exposed connector pins in the adaptor before follow-up step.

Proper PV configuration should be used to ensure suitable input voltage

range for PV charger of EMERGY 1000 (refer to product specifications).

Excessive voltage level (>200V) may result in damage to PV charger.

- 9 -

3.3 System Outputs

3.3.1 AC Output

AC outlet(s) of EMERGY 1000 provided is (are) also compatible with local electrical plugs. To utilize

AC output, the following steps are to be followed.

Step 1: Turn on the system by pressing MSW.

Step 2: Turn on AC output(s) by pressing AC OUT SW. AC OUT INDICATOR will turn on.

Step 3: Connect power cord of apparatus, equipment or appliance to AC OUT (AC outlet).

To discontinue using AC output, simply remove power cord of load unit from AC OUT or turn off AC

output by pressing AC OUT SW again. AC OUT INDICATOR will turn off.

The voltage and frequency range of the apparatus, equipment or appliance

should comply with the output voltage and frequency range of EMERGY

1000 to avoid under-performance or damage to the load unit.

3.3.2 DC (USB) Output

DC (USB) output is turned on and off in accordance with the system. When system is turned on

(thru pressing MSW), DC output is also turned on. When the system is turned off, DC output is also

turned off. A total of 2A current is available for the two USB outlets.

3.4 Operating Modes

The default operating mode for EMERGY 1000 is “Standby” mode. To toggle between “Standby”

mode and “On-Line” mode, lightly press MODE button. MODE INDICATOR will turn on under

“On-Line” mode and turn off under “Standby” mode.

3.4.1 Standby Mode

Under Stand-by mode, AC Output power will automatically be supported by the battery when AC

input power disappears. The typical transfer time is less than 16mS.

3.4.2 On-Line Mode

Under On-Line mode, AC Output power is supported by the battery all the time. It is no time for

delay when AC input power disappears and the system has energy. AC Output is constantly

regulated as a refined voltage source that are suitable for sensitive electronics.

The continuous output power under this mode is however limited to 525W. The maximum output

power though can reach 1,500W with the duration depending on the battery’s state of charge.

Inhaltsverzeichnis

Andere FSP Technology Lagerung Handbücher

FSP Technology

FSP Technology EnerX 3000 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung