Fuji Electric MICREX-F Series Bedienungsanleitung

Fuji Electric Co.,Ltd.

MICREX-F Series

SIO Driver

1 System Configuration.......................................................................................................3

2 Selection of External Device............................................................................................7

3 Example of Communication Setting.................................................................................8

4 Setup Items....................................................................................................................24

5 Cable Diagram...............................................................................................................29

6 Supported Device...........................................................................................................44

7 Device Code and Address Code....................................................................................46

8 Error Messages..............................................................................................................47

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display and the External Device (target PLC).

In this manual, the connection procedure will be described by following the below sections:

1System Configuration

This section shows the types of External

Devices which can be connected and SIO

type.

)"1 System Configuration" (page 3)

2Selection of External Device

Select a model (series) of the External

Device to be connected and connection

method.

)"2 Selection of External Device" (page 7)

3Example of Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

)"3 Example of Communication Setting"

(page 8)

4Setup Items

This section describes communication

setup items on the Display.

Set communication settings of the Display

with GP-Pro Ex or in offline mode.

)"4 Setup Items" (page 24)

5Cable Diagram

This section shows cables and adapters

for connecting the Display and the

External Device.

)"5 Cable Diagram" (page 29)

Operation

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The system configuration in the case when the External Device of Fuji Electric Co.,Ltd. and the Display are

connected is shown.

Connection Configuration

RS232C

• 1:1 Connection

Series CPU Link I/F SIO Type Setting Example Cable

Diagram

File Switch

MICREX-F

F80H

F120H

F250

RS232C interface

on FFU120B RS232C Setting

Example 1

(page 8)

Setting

Example 2

(page 11)

Cable

Diagram 1

(page 29)

RS485 interface

on FFU120B RS422/485

(4wire)

Setting

Example 3

(page 13)

Setting

Example 4

(page 16)

Cable

Diagram 2

(page 32)

F30 *1

F50 *1

F60

F70

F70S

F80

F80H

F81

F120

F120H

F120S

F200

F250

*1 When you use F30 or F50 for T link connection, T link master adaptor (FTM050A) is necessary.

RS232C interface

on FFK120A-C10 RS232C Setting

Example 1

(page 8)

Setting

Example 5

(page 18)

Cable

Diagram 1

(page 29)

RS485 interface

on FFK120A-C10 RS422/485

(4wire)

Setting

Example 3

(page 13)

Setting

Example 6

(page 20)

Cable

Diagram 2

(page 32)

FFK100A-C10 *2

*2 You cannot use FFK100A-C10 or NC1L-RS2 in 1:n configuration.

RS232C --- Setting

Example 7

(page 22)

Cable

Diagram 3

(page 42)

F70

F70S NC1L-RS2*2 *3

*3 When you install 2 link units on the extension base unit created by T link function based on the basic base

unit of the External Device, you can connect the Display on either of 2 link units (simultaneous connection

on both 2 link units are not available). When you install 2 basic base units, simultaneous connection on both

2 link units are available.

RS232C Setting

Example 1

(page 8)

Setting

Example 2

(page 11)

Cable

Diagram 4

(page 43)

External Device

RS232C

Display

Operation mode:1

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 4

• 1:n Connection

* Turn ON the termination resistance switch on the interface which terminates the RS422 connection.

RS422/485 (4wire)

• 1:1 Connection

* Turn ON the termination resistance switch on the External Device interface.

• 1:n Connection

* Turn ON the termination resistance switch on the interface which terminates the RS422 connection.

RS232C

External Device*

External Device External Device*

RS422/485 (4wire)

Operation mode:2 Operation mode:3

Operation mode:3

Max 16 units

Display

RS422/485 (4wire)

External Device*

Operation mode:

RS422/485 (4wire)

Display

Operation mode:3 Operation mode:

Operation mode:3

Max 16 units

RS422/485 (4wire)

Display

RS422/485 (4wire) RS422/485 (4wire)

External Device External Device External Device*

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 5

IPC COM Port

When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please

refer to the IPC manual for details.

Usable port

DIP Switch setting: RS-232C

Series Usable Port

RS-232C RS-422/485(4 wire) RS-422/485(2 wire)

PS-2000B COM1*1 , COM2,

COM3*1, COM4

*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.

PS-3450A, PS-3451A,

PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2

PS-3650A (T41 model),

PS-3651A (T41 model) COM1*1 --

PS-3650A (T42 model),

PS-3651A (T42 model) COM1*1*2, COM2 COM1*1*2 COM1*1*2

PS-3700A (Pentium®4-M)

PS-3710A COM1*1, COM2*1,

COM3*2 , COM4

*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.

COM3*2 COM3*2

PS-3711A COM1*1, COM2*2 COM2*2 COM2*2

PS4000*3

*3 When making communication between an External Device and COM port on the Expansion slot,

only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the

specification of COM port.

For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.

Please refer to the IPC manual for details of pin layout.

COM1, COM2 - -

PL3000 COM1*1*2, COM2*1,

COM3, COM4 COM1*1*2 COM1*1*2

DIP Switch Setting Description

1OFF

*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.

Reserved (always OFF)

2OFF

SIO type: RS-232C

3OFF

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 6

DIP Switch setting: RS-422/485 (4 wire)

DIP Switch setting: RS-422/485 (2 wire)

DIP Switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

DIP Switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available

8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available

9ON

RS (RTS) Auto control mode: Enabled

10 ON

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 7

2 Selection of External Device

Select the External Device to be connected to the Display.

Setup Items Setup Description

Number of Devices/

PLCs Enter an integer from 1 to 4 to define the number of Devices/PLCs to connect to the

display.

Manufacturer Select the manufacturer of the External Device to connect. Select "Fuji Electric Co.,Ltd.".

Series

Select the External Device model (series) and the connection method. Select "MICREX-F

Series SIO".

In System configuration, make sure the External Device you are connecting is supported by

"MICREX-F Series SIO".

)"1 System Configuration" (page 3)

Port Select the Display port to be connected to the External Device.

Use System Area

Check this option to synchronize the system data area of the Display and the device

(memory) of the External Device. When synchronized, you can use the External Device’s

ladder program to switch the display or display the window on the Display.

Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"

This feature can also be set in GP-Pro EX or in the Display's offline mode.

Cf. GP-Pro EX Reference Manual "System Settings [Display Unit] - [System

Area] Settings Guide"

Cf. Maintenance/Troubleshooting Guide "Main Unit - System Area Settings"

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 8

3 Example of Communication Setting

Examples of communication settings of the Display and the External Device, recommended by Pro-face, are

shown.

When you use the MICREX-F Series, use GP-Pro EX and the ladder software to set as below.

3.1 Setting Example 1

Settings of GP-Pro EX

Communication Settings

To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 9

Device Setting

To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]

window, select the external device and click [Settings] .

To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add

Device] to add another External Device.

Setting of External Device

(1) Turn OFF the DIP switch No.8 "Initialization method" on the rear panel of general-purpose interface module

of the External Device. Other settings are not necessary. The DIP switch setting will be effective after restart.

Use the rotary switch for MODE setting.

(2) Set the mode switch key of the External Device body to [TERM].

(3) Startup the ladder software. Execute [New File] from the [File] menu.

(4) Select the model of the External Device to use.

No. Setup Items Setup Description

1 No need

Unused

2 No need

3 No need

4 No need

5 No need

6 No need

7 No need

8OFF Initial file setting effective

MICREX-F Series SIO Driver

GP-Pro EX Device/PLC Connection Manual 10

(5) Create the default file in the data table. Please refer to the manual of the External Device for the default file

number or the setting method. When you select MODE2 or 3, use the rotary switch to specify the same

number as the station No. in the device setting. The setting is not necessary for MODE1 (RS232C 1:1

connection). Please refer to the connection configuration diagrams for more details.

(6) Select [Transfer] from the [File] menu to transfer to the External Device body.

(7) After the transfer is completed, restart the External Device.

Setup Items Setup Description Notes

MODE switch Depending on connection type Set by the rotary switch

Station No. Depending on connection type

Transmission Procedure No procedure

Set by the initial file

Mode Settings

Baud rate 19200

Data Bit 7

Parity Bit Even

Stop Bit 2

DCE/DTE DCE

CTS/RTS Always ON

DSR/DTR Always ON

Send Condition None

PK Access Enable

Transmission Code JIS

Code Conversion Enable

Head Code STX

End Code ETX

Head Code 1, 2 0

End Code 1, 2 0

BCC None

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fuji Electric Controller Handbücher

Fuji Electric

Fuji Electric Faldic-a RYS-R Series Bedienungsanleitung

Fuji Electric

Fuji Electric frenic-hvac Bedienungsanleitung

Fuji Electric

Fuji Electric micrex-sx SPH Bedienungsanleitung

Fuji Electric

Fuji Electric FEH300b Gebrauchsanweisung

Fuji Electric

Fuji Electric PXZ Series Bedienungsanleitung

Fuji Electric

Fuji Electric PXF4 Bedienungsanleitung

Fuji Electric

Fuji Electric PXV3 SERIES Bedienungsanleitung

Fuji Electric

Fuji Electric Micro Control X Bedienungsanleitung

Fuji Electric

Fuji Electric ALPHA7 Bedienungsanleitung

Fuji Electric

Fuji Electric MICREX-SX series Bedienungsanleitung

Fuji Electric

Fuji Electric MICREX-SX series SPF Bedienungsanleitung

Fuji Electric

Fuji Electric FD5000 series Bedienungsanleitung

Fuji Electric

Fuji Electric Model: PXR4 Bedienungsanleitung

Fuji Electric

Fuji Electric FRENIC-HVAC series Bedienungsanleitung

Fuji Electric

Fuji Electric CC-M Bedienungsanleitung

Fuji Electric

Fuji Electric PXG9 Gebrauchs- und Pflegehandbuch

Fuji Electric

Fuji Electric Frenic Bedienungsanleitung

Fuji Electric

Fuji Electric Micro Control X Series Bedienungsanleitung

Fuji Electric

Fuji Electric NA0AX06-MR Bedienungsanleitung

Fuji Electric

Fuji Electric FRENIC-EcoPAK Bedienungsanleitung

Fuji Electric

Fuji Electric FALDIC-a Bedienungsanleitung

Fuji Electric

Fuji Electric POD UG221H-LE4 Bedienungsanleitung

Fuji Electric

Fuji Electric SPH Series Bedienungsanleitung

Fuji Electric

Fuji Electric Micro Controller X PXG4 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung