Fujion FR-LT2290V Handbuch
Contents
2 3
4567
8 9 10 11
12
Warning
Caution
Safety warning
Product structure schematic
Outline dimension
Control panel operation
Precautions
Daily maintenance
Specifications
The installation guide
Electrical schematic diagram
Cleaning and maintainance
Troubleshooting
After service
Warranty notice
2
2
3
4
4
5
5
6
6
7
8
10
10
11
11
12
Packing list
Warning
Caution
Accessible parts may become hot when used with cooking appliances.
3
4567
8 9 10 11
12
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision. If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
There shall be adequate ventilation of the room when the cooker hood is used at the same
time as appliances such as burning gas or other fuels.
Please do not use corrosive detergent for cleaning. The proper function of the unit is
conditioned by the regularity of the maintenance.
To protect the main body from corrosive formed by the long time accumulation of dirt, the cooker
hood should be cleaned with hot water with non-corrosive detergent in every two months.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Do not flame under the cooker hood.
The air must not be discharged into a flue that is used for exhausting fumes from
appliances such as burning gas or other fuels.
Regulations concerning the discharge of air must be fulfilled.
●
●
●
●
●
●
●
●
●
The minimum distance between the top most part of the cooking appliance such as gas hob
and the lowest part of the cooker hood, when it is located exactly over the cooking appliance,
shall be at least 650mm. If greater distance is specified in the manual of the cooking appliance,
it must be taken into account.
2
This hood is an external exhaust type cooker hood, and the gas
should not be discharged into the hot flue gas
through burning gas or other fuel.
If the cooker hood is installed above the gas stove, the distance from the bottom of the body
to the focal plane is at least 650mm, which should be considered if the installation instruc-
tions of gas-fired stoves provide a larger installation distance.
It is strictly forbidden to modify the product without authorization, and the power cord shall
not be replaced or modified by itself.
Please do not install the cooker hood machine on the wall of flammable material.
Do not install the cooker hood machine on the top of the stove with solid fuel.
When drilling holes in the wall, avoid electrical wires embedded in the wall to avoid electric
shock hazard.
A special power supply socket shall be used for the cooker hood machine, and the special
power outlet should be reliably grounded (the product must use 10A, 220~V or above).
The wall shall have sufficient supporting strength for the installation of the cooker hood
machine. The hollow core of the wall shall be greater than 30mm, and the concrete
wall can be directly punched and installed. The product must be securely mounted on the
wall.
The cooker hood may have very sharp edges. Please wear protective gloves when
you install or clean the cooker hood.
If your kitchen is under a state of decoration, do not use cooker hood exposed, for building
materials, dust, paint, coatings and their volatile gas cooker hood surface causes corrosion
and lose luster, please install cooker hood in after the decoration.
●
●
●
●
●
●
●
●
●
●
the cooker hood machine
used for the discharge of smoke produced
●
The appliance is not intended for use by young children or infirm
persons without supervisions.
Young children should be supervised to ensure they do not play with
the appliance.
Plug the power cord to socket outlet with earthing continuity terminal.
The cooker hood is for home use only, not suitable for barbecue, roast
shop and other commercial purposes.
the instruction.
Do not use open flame, or allow the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer,
service agent or similarly qualified person in order to avoid a hazard.
The replaced power cord should be provided by manufacturer or seller.
There is a fire risk if cleaning is not carried out in accordance to the
instruction.
In case of damaged connecting wire, please refer to the manufacturer,
after-sale service personnel or other qualified technicians.
Use the product according to the instructions to avoid any fire hazard.
The exhaust air must not be introduced into a smoke flue or chimney
that is used for exhausting fumes from appliances such as burning gas.
Follow the local laws applicable for external air evacuation.
Safety warning
The cooker hood and its filter should be cleaned regularly according to
Please ensure that there is an adequate ventilation in the room while
the cooker hood is in operation.
Please ensure that the power plug is disconnected from the socket or
turn off the breaker before cleaning or maintaining the hood.
flame to go beneath
3
Oil Tray
4
1
56
78
11
9
10 12
13
4
1
5
6
7
8
Ref. Qty. Product Components
Screws(ST4.2×16)
Screw (M5×16)
Screws(ST4.2×9.5)
Plastic expansion pipe
Cross - groove countersunk
head wood screw（M5×50）
12
9
10
11
13
Ref. Qty. Product Components
1
1
1
1
1
1
1
4
1
2
7
6
1
Product structure schematic
Packing list
Flexible Tube Duct
Exhaust Outlet
Exhaust Outlet sealing gasket
Hanging Bracket
Duct Cover Fixing Bracket
Rectifier Panel
2
4 5 6 7
8 9 10 11
12
14
14 Screw(ST5×45)
1
15
15 2Screws(ST2.9×9.5)
Limit Block
4
Slide Duct Cover
Duct Cover
Oil Panel
LED Lighting
Rectifier Panel Oil Tray
Switch Panel
Outline dimension(unit: mm)
Control panel operation
407
0~285
316
2 3
5 6 7
8 9 10 11
12
896 494
672
Light
Gesture
Boost
Low
Switch
Short press: Turn on or off the light.
1st Short press: Start up(hight speed);
2nd
min, fan will runs at the low speed;
3rd Twice short press: OFF immediately.
Long press :2~3 seconds
Short preShort press:0.5 second
Short press: Turn on/off gesture control.
7 X Screws(M5*50)
Palm from left to right or from right to left is to start or close
the range hood.
High Short press: Turn on the power.
Press High speed: Turn on high speed .
Press Low speed: Turn on low speed.
(Two speed can't run at the same time)
Short press: Delay 3
Short press: Operation start at boost speed.Please start operation
manually if boost speed is to be used for more than 3 minutes.
5
On off state, Long press: Enter clean mode,except the light, other keys
are not operable.
1st
2nd
Long press: Exit clean mode.
Touch buttons light status: Off, Half on, On, Flickering
Precaution
Daily maintenance
Surface cleaning
Please note that the power supply voltage and frequency should be consistent to the
voltage and frequency required for the product.
Please make sure that the oil tray has been properly installed.
In the cooking process, please keep the kitchen environment well ventilated.
Do not handle the power cord with wet hand.
Do not pull the power cord to pull out the power cord plug.
If you do not use the cooker hood for a long time, please unplug the power cord.
Always clean the surface and screen of the cooker hood. Do not use 1.
2.
3.
●
●
●
●
●
●
●
●
Oil tray window
2 3
46 7
8 9 10 11
12
During operation, if abnormal conditions (abnormal noise, odor, smoke, fever),
When the cooker hood is working, do not place hands into the fan or operation area.
hood body
gets heated) are observed, immediately turn off the power and unplug the power cord from
the breaker.
harsh sponge or
brush to avoid surface scratching of the product.
When oil is visible from the oil tray window, please timely
maintain the oil tray to avoid oil dripping.
Remove the rectifier panel by referring to the disassembly method mentioned below.
Then, clean the rectifier panel by soaking it in warm water with neutral detergent. Use a
soft brush to clean the residue.
NOTE: Make sure to wear gloves during maintenance.
6
Guide for disassembly of rectifier panel
Remove the rectifier panel as indicated
2. After the rectifier panel is opened, hold
the rectifier panel with both hands and
remove it horizontally.
1. Hold the rectifier panel with both hands,
and press the left and right sides to
open the rectifier panel.
2 3
4 5 6 7
910 11
12
Specifications
87
Rated voltage
(v) Speed (w)
Power consumption Air flow
(m³/h) Sound
(dB)
220
240
230
Boost
High
Low
Boost
High
Low
Boost
High
Low
LED light information
Max Power Voltage Picture Lamp Cap
Square / Dimension:
120mm x 33.2mm 1.5W DC 12 V ——
The installation guide
To determine the location (unit: mm)
1
The range hood machine should be installed horizontally and above the cooker.
The installation diagram is as follows.
Installation of Hanging Bracket (unit: mm)
2
Installation precautions
Exhaust pipe to the cabinet
installation diagram
Schematic diagram of opening size
of exhaust pipe at the ceiling
150
75
200
905~915
672~957
407
316
center line of cooker hood
Hanging Bracket
After installation of the cooker hood, the left and right level should be maintained.
Should avoid excessive windows and air convection in the vicinity of the cooker hood,
otherwise it will affect the efficiency of the cooker hood.
Exhaust pipe requirements.
The exit of the exhaust pipe should not be too long.
●
●
●
●
2 3
4 5 6 7
810 11
12
≥650
As shown in the picture on the right, drill 4 screw
holes with 10mm diameter and 50 to 60mm depth,
install 4 plastic expansion pipes inside the manhole
with 4 M5×50 countersunk head wood screws to fix
the hanging bracket and reliable.
9
8
1300-1600
＞1190 120
20-40
180
310
324
Duct Cover
Fixing Bracket
Limit Block hole
Installation of Exhaust Outlet
3
Installation of the machine
4
The installation of flexible tube duct
5
Installation of Slide Duct Cover
6
Install the exhaust outlet components together with the exhaust
the blade is rotating flexibly.
Align the hole in the rear of the body to the hanger of the
the cooker hood, confirm the installation level of the
machine.Hold the limit block against the machine and
If the flexible tube duct is too long, please adjust the long
tube to the contraction state and fix it with adhesive tape
to prevent the pipe from swinging during the working process.
According to the installation height and duct cover fixing
bracket mounting holes, drill 2 holes in the wall with 10mm
diameter and 50 to 60mm depth, the plastic expansion
pipe pressure inside the hole, provided with 2 M5 x50
cross - groove countersunk head wood screw will cover
duct cover fixing bracket reliable fixation. the slide duct
cover to the corresponding height, and use the 2
ST4.2 x 9.5 screws on the duct cover fixing bracket.
Hang hole
The hanging
2 3
4 5 6 7
8 9 11
12
outlet sealing gasket in the position of the rack outlet, tighten
with 4 ST4.2 x 16 screws , check and make sure that
Exhaust outlet
Exhaust outlet sealign gasket
hanging bracket, and hang it from the top down. After hanging
Flexible Tube Duct
Exhaust Outlet
Slide Duct
Cover
Duct Cover
Fixing Bracket
bracket
10
9
Limit block
and fix the limit block reliably with ST5 x 45 screw to
prevent the machine from falling off accidentally.
Set one side of flexible tube duct in the exhaust outlet
with 2 ST2.9x9.5 as shown, and wrap the aluminum foil
tape around the installation joint of the exhaust outlet
and the flexible tube duct. Then connect the other side
of the flexible tube duct to the outdoor or public flue.
Inhaltsverzeichnis
Andere Fujion Dunstabzugshaube Handbücher
