Fujitsu AX SERIES Bedienungsanleitung

Supplied by

FUJITSU GENERAL (AUST.) PTY LIMITED

ACN 001229554

A Subsidiary of FUJITSU GENERAL LIMITED

HEAD OFFICE

SYDNEY : E&F Rydalmere Business Park,

10-16 South Street, Rydalmere, N.S.W. 2116 TEL.[02]638 5199

MELBOURNE : 2nd Floor, 1-3 Wellington Street, Windsor, VIC. 3181

(also all Tasmanian enquiries) TEL.[03]510 8652

BRISBANE : 5th Floor, 301 Coronation Drive Milton, QLD. 4064 TEL.[07]367 2008

ADELAIDE : 146 Fullarton Road, Rose Park, S.A. 5067 TEL.[08]364 0588

PERTH : Unit 6, 103 Erindale Road Balcatta W.A. 6021 TEL.[09]345 2011

OPERATING MANUAL

ROOM AIR CONDITIONER

AX SERIES

Cool & Heat type

(Reverse Cycle)

22 50 Hz MODEL

P/N 9353031037

FUJITSU GENERAL LIMITED

FGE_9353031037 1/9/04, 11:02 AM1

567

WARM

COOL

THERMOSTAT MASTER CONTROL

OFF

SUPER

QUIET

HIGH

POWER

HIGH

POWER

SUPER

QUIET

LOW FAN

HIGH FAN

OPEN

EXHAUST AIR

SELECT LEVER

NEUTRAL SUPER WAVE ZONE

SUPER WAVE

ON OFF

NAME OF PARTS

Before Starting

In order to enable efficient and trouble-free operation of your air conditioner, connect

the power plug of your air conditioner through an exclusive circuit, having a time delay

fuse, to the correct power supply described on the rating plate. (240V, 50 Hz)

Control Panel

Hold the lower edge of the control panel cover and pull up-

ward until it reaches its stopper.

Operation controls provided are THERMOSTAT, MASTER

CONTROL, SUPER WAVE switch and EXHUAST AIR control.

THERMOSTAT knob

SELECT LEVER

CLOSE OPEN

EXHAUST AIR

NEUTRAL SUPER WAVEZONE

Front panel

Vertical louver

Control panel cover

Control panel

SUPER WAVE

switch

SUPER WAVE

ZONE

SELECT LEVER

EXHAUST AIR

control lever

MASTER CONTROL knob

FGE_9353031037 1/9/04, 11:02 AM2

CONTROL POSITION FUNCTION

HIGH POWER (RED) Fan (High Speed) and compressor operate

Rapid heating effect at top capacity.

SUPER QUIET (RED) Fan (Low Speed) and compressor operate

Intermediate heating effect and

reduced operating noise.

HIGH FAN High fan speed without heating/cooling

Room air is circulated and cleaned.

MASTER OFF The air conditioner is switched off.

CONTROL LOW FAN Low fan speed without heating/cooling

Room air is circulated and cleaned.

SUPER QUIET (BLUE) Fan (Low Speed) and compressor operate

Intermediate cooling effect and

reduced operating noise.

HIGH POWER (BLUE) Fan (High Speed) and compressor operate

Rapid cooling effect at top capacity.

THERMOSTAT WARM

COOL Amount of heating/cooling is maintained automatically. Turn knob counterclock-

wise/clockwise to obtain most comfortable heating/cooling.

Vertical louvers continuously change the direction of air flow.

ON When the MASTER CONTROL knob is set to “OFF”, the SUPER WAVE does not

SUPER WAVE operate.

OFF Vertical louvers stop enabling air flow to be directed in any desired direction.

SELECT LEVER This lever is used to adjust the air flow direction and sweep angle. For details,

refer to pages 6 ~ 9.

EXHAUST AIR CLOSE Exhaust vent is closed.

OPEN Room air is drawn outside.

SELECT LEVER

NEUTRAL SUPER WAVE ZONE

FGE_9353031037 1/9/04, 11:02 AM3

Cooling

To obtain maximum cooling effect in the hot summer, select

position HIGH POWER (BLUE) on the MASTER CONTROL.

Maximum moisture removal, air circulation and dust removal

are effected at the same time.

Selection of SUPER QUIET (BLUE) reduces operating noise.

Heating

To obtain maximum heating effect in severe winter select

position HIGH POWER (RED) on the MASTER CONTROL.

Maximum air circulation is obtained at the same time.

Selection of SUPER QUIET (RED) reduces heating effect and

operating noise. However you may feel a higher tempera-

ture at the air outlet compared to the HIGH POWER (RED)

position, due to the reduced fan speed.

NOTE:

After you start driving, it will take approximately 10

minutes for the air from this unit become warm.

This delay is normal.

If you find that insufficient room heat is produced, we

recommend that you use the air conditioner together with

other heating appliances.

Air Circulation

To maintain a comfortable room temperature, an important

factor is the circulation of air. Room air can be circulated

without cooling/heating by selecting either HIGH FAN or LOW

FAN position on the MASTER CONTROL.

Circulation of air without cooling/heating can be also effected

as follows:

1. When operating with the MASTER CONTROL switched

to HIGH POWER (RED) or SUPER QUIET (RED), turn the

thermostat fully clockwise.

2. When operating with the MASTER CONTROL switched

to HIGH POWER (BLUE) or SUPER QUIET (BLUE), turn

the thermostat fully counterclockwise.

Thermostat Control

Once the thermostat is set to the desired temperature, the

room temperature will be automatically adjusted without

excessive or insufficient cooling/heating and thus a com-

fortable environment is always maintained.

When cooling, turn the THERMOSTAT knob clockwise to

increase cooling effect.

When heating, turn the THERMOSTAT knob counterclock-

wise to increase heating effect.

The thermostat controls the compressor only, and accordingly

the fan is constantly circulating air even during the period when

the compressor is off during cooling/heating operation. To stop

the cooling/heating operation set the master control OFF

position.

1. When you wish to lower the temperature, turn the THER-

MOSTAT knob clockwise in the direction of the higher

numbers on the dial.

2. When you wish to increase the temperature, turn the

THERMOSTAT knob counterclockwise in the direction of

the lower numbers.

3. When the THERMOSTAT is set at positions “5”, “6” or

“7”, comfortable room temperatures can usually be

obtained. Please note that it is unhealthy for the room

temperature to be lower than approximately 22˚C.

4. When the THERMOSTAT is positioned at “10”, the room-

side fin coil may freeze up due to excessively low room

temperature (for example, below 18˚C) caused by low

outdoor temperature at night.

FGE_9353031037 1/9/04, 11:02 AM4

Once the fin coil becomes frozen, the air flow from the air

conditioner is restricted by the frost, and the room tem-

perature may rise due to the resultant weak cooling per-

formance of the air conditioner.

5. The THERMOSTAT positions “8”, “9” and “10“ can be

used when the room temperature does not become suffi-

ciently low. This condition may occur when the thermo-

stat switches off automatically because cooled air, when

it passes through the horizontal louvers positioned down-

wards and the vertical louvers positioned to the left, makes

a short circuit and the recirculated air touches the sensor

of the thermostat.

NOTE: The thermostat controls the compressor only and

accordingly the fan is constantly circulating air even

during the period when the compressor is off.

Important

When cooling/heating is stopped by means of either the

MASTER CONTROL or THERMOSTAT do not restart cooling/

heating for at least three (3) minutes. If cooling/heating is

restarted within this time, the compressor motor will be

subjected to an over current and a compressor motor safety

device will be actuated. If this occurs, restarting cooling/

heating will not be possible for about 20 minutes.

Automatic Defrosting

When continuous heating is effected for a long period of

time with low outside temperatures, the condenser tends to

frost up and heating efficiency will drop. To prevent this

condition, the unit is equipped with an automatic defrosting

system.

When frosting occurs the fan is stopped automatically. After

5 or so minutes the frost will have melted and the normal

heating function is then automatically returned.

Exhaust Air Control

By setting EXHAUST AIR control lever to the appropriate

positions between “OPEN” and “CLOSE” positions, it is

possible to expel the room air to the desired extent. The

quantity of air to be expelled will increase when the lever is

positioned closer to the “OPEN” position.

NOTE:

Cooling/heating effect will be reduced when operating

EXHAUST open.

Air Direction Control

When the SUPER WAVE switch is turned to “ON” position,

the vertical louver is automatically actuated and sweeps the

jet of air alternately, right and left and thus more effective

cooling/heating will be obtained.

Louvers may be stopped at any position when SUPER WAVE

switch is turned off.

Sweep angle and direction can be adjusted with the select

lever. The sweep can span an area either to the right or to

the left. Select a sweep angle suitable to the layout of the

room and the position of the air conditioner in the room

which the air conditioner is installed.

FGE_9353031037 1/9/04, 11:02 AM5

Air Flow Adjustment

With this air conditioner, three air directions can be obtained

as shown in the figures below. When the air flow direction

is set, adjust to the desired sweep angle.

NOTE: Setting the vertical louver at high room humidity.

1. Set the SUPER WAVE switch to ON.

2. Or, to use with the SUPER WAVE switch to OFF,

set the switch to OFF when the vertical louver

moves to the center.

Adjusting Sweep Angle

When the select lever is moved to the right or left, the sweep

angle increases or decreases. Adjust the sweep angle within

SUPER WAVE ZONE range.

NOTE: When the select lever is returned to the “NEUTRAL”,

the vertical louvers do not normal operate. If the

select lever is returned to the “NEUTRAL” in error,

readjust the sweep angle referring to “Adjusting Air

Flow Direction and Sweep Angle”.

SUPER WAVE

ON OFF

SELECT LEVER

NEUTRAL

MASTER CONTROL

NEUTRAL

Min Max

SUPERWAVE ZONE

Select lever

SUPER WAVE ZONE

Air conditioner

Room

Right side Center Left side

Air conditioner Air conditioner

Room Room

FGE_9353031037 1/9/04, 11:02 AM6

SUPER WAVE

SELECT LEVER

ON OFF

SUPER WAVE

SELECT LEVER

ON OFF

Adjusting Air Flow Direction and Sweep

Angle

1Move the select lever fully left to the “NEUTRAL”.

2Position the vertical louvers approx. at the center and

move the select lever fully to the right end of the SUPER

WAVE ZONE.

3Set the SUPER WAVE switch to “ON”.

The vertical louvers start rotating with the maximum

sweep angle.

NOTE: If the MASTER CONTROL knob is set to “OFF”,

set it to the other position.

4The sweep angle can be adjusted within the SUPER WAVE

ZONE range. When the select lever is returned to the left,

the sweep angle decreases. Adjust sweep angle accord-

ing to preference.

NOTE:

If the select lever is returned to the “NEUTRAL”in

error, the vertical louvers do not function properly.

In this event, carry out the procedure from the

beginning.

Vertical louver

Stop at the center

To direct air flow to center:

FGE_9353031037 1/9/04, 11:02 AM7

SUPER WAVE

SELECT LEVER

ON OFF

SUPER WAVE

SELECT LEVER

ON OFF

1Move the select lever fully left to the “NEUTRAL”.

2Lightly move the vertical louvers to the left until they stop,

and move the select lever fully to the right end of the

SUPER WAVE ZONE.

3Set the SUPER WAVE switch to “ON”.

The vertical louvers start rotating with the maximum

sweep angle.

NOTE: If the MASTER CONTROL knob is set to “OFF”,

set it to the other position.

4The sweep angle can be adjusted within the SUPER WAVE

ZONE range. When the select lever is returned to the left,

the sweep angle decreases. Adjust sweep angle accord-

ing to preference.

NOTE:

If the select lever is returned to the “NEUTRAL”in

error, the vertical louvers do not function properly.

In this event, carry out the procedure from the

beginning.

Vertical louver

Move to the left

To direct air flow to left side:

FGE_9353031037 1/9/04, 11:03 AM8

SUPER WAVE

SELECT LEVER

ON OFF

SUPER WAVE

SELECT LEVER

ON OFF

1Move the select lever fully left to the “NEUTRAL”.

2Lightly move the vertical louvers to the right until they

stop, and move the select lever fully to the right end of

the SUPER WAVE ZONE.

3Set the SUPER WAVE switch to “ON”.

The vertical louvers start rotating with the maximum

sweep angle.

NOTE: If the MASTER CONTROL knob is set to “OFF”,

set it to the other position.

4The sweep angle can be adjusted within the SUPER WAVE

ZONE range. When the select lever is returned to the left,

the sweep angle decreases. Adjust sweep angle accord-

ing to preference.

NOTE:

If the select lever is returned to the “NEUTRAL”in

error, the vertical louvers do not function properly.

In this event, carry out the procedure from the

beginning.

Vertical louver

Move to the right

To direct air flow to right side:

FGE_9353031037 1/9/04, 11:03 AM9

MAINTENANCE

Room Air Filter

A filter is provided on the rear of the removable panel. Since

the function of this filter is to filter dust and dirt in the air,

please clean it regularly before it becomes clogged with dust.

Wash the filter with clean water. If it is very dirty, rinse it in a

synthetic detergent before washing in clean water. Allow

the filter to dry thoroughly in the shade after washing.

Remove the filter in the following manner.

Using the frip position, push the bottom of the removable panel

up with your hand, pull it toward you, and the removable panel

will be easily removed (See Fig. 1, Fig. 2).

The filter is attached to the rear side of the removable panel.

Pull the lower edge of the filter forward in order to remove

the filter from the removable panel (See Fig. 3). To replace

the filter, insert the top edge of the filter under the hooks at

the top of the removable panel, then press into the two lower

hooks to fix into place (See Fig. 4).

When you want to refit the removable panel, insert it by

pushing the upper edge of the removable panel against the

upper part of the front panel. How to Remove the Front Panel

Remove the front panel in the following manner.

The front panel is attached to the cabinet with snap clips at

the top and screws at the bottom. Remove the removable

panel first and you will see two screws at the left and right

of the bottom side. Take them off. (See Fig. 5) Hold up the

front panel with your hands to remove it completely. (See

Fig. 6) When refitting the front panel, insert the two clips on

the upper part of the panel into the two slots at the top side

of the cabinet. Press the front panel at its bottom side and

fix it with screws. This completes refitting of the front panel.

Removable panel

Front panel

Fig. 1 Fig. 2 Removable panel

Filter

Removable panel

Upper hooks

Lower

hooks

Fig. 3 Fig. 4

FGE_9353031037 1/9/04, 11:03 AM10

Inhaltsverzeichnis

Andere Fujitsu Klimaanlage Handbücher

Fujitsu

Fujitsu AOYG24KBTB Service-Handbuch

Fujitsu

Fujitsu AUXG18KVLA Service-Handbuch

Fujitsu

Fujitsu D'EMPLOI Bedienungsanleitung

Fujitsu

Fujitsu AS* G09LECB Original Betriebsanleitung

Fujitsu

Fujitsu General ASHG07KMTA Bedienungsanleitung

Fujitsu

Fujitsu AUTG09LVLB Service-Handbuch

Fujitsu

Fujitsu ARYA36LCTU Bedienungsanleitung

Fujitsu

Fujitsu Airstage ASYA07GACH Bedienungsanleitung

Fujitsu

Fujitsu AUXG24LRLB Bedienungsanleitung

Fujitsu

Fujitsu AIRSTAGE ASTH24CNTA Bedienungsanleitung

Fujitsu

Fujitsu ABYA12-24LBTH Bedienungsanleitung

Fujitsu

Fujitsu AOU30RLXEH Service-Handbuch

Fujitsu

Fujitsu Airstage ARUH72TLAV1 Bedienungsanleitung

Fujitsu

Fujitsu ASU9R1A Bedienungsanleitung

Fujitsu

Fujitsu ARYG24LMLA Bedienungsanleitung

Fujitsu

Fujitsu ARG60LHTA Original Betriebsanleitung

Fujitsu

Fujitsu ARYG30LMLE Bedienungsanleitung

Fujitsu

Fujitsu AIRSTAGE V-II Bedienungsanleitung

Fujitsu

Fujitsu ARU12RLF Installations- und Benutzerhandbuch

Fujitsu

Fujitsu ASU-RLF Montageanleitung

Fujitsu

Fujitsu Inverter Halcyon ASU9R2 Bedienungsanleitung

Fujitsu

Fujitsu SPLIT TYPE AIR CONDITIONER Bedienungsanleitung

Fujitsu

Fujitsu AJ*A72LALH Series Bedienungsanleitung

Fujitsu

Fujitsu ABYG36KRTA Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung