Fujitsu Plasmavision PDS6101W-H Bedienungsanleitung
PDS6101W/E-H
PDS6101W/E-S
Copy Prohibited
FUJITSU GENERAL Proprietary
- 4 -
SPECIFICATIONS
Power requirement 100-240V, 50/60Hz
Current drain 7.5A
Display panel
Screen size 131.1 (W) x 76.0 (H) [cm]
53.1 (W) x 29.9 (H) [inch]
Aspect ratio 16 : 9
Number of pixels 1,365 (H) x 768 (V) pixels
Pixel pitch 0.99mm x 0.99mm
Contrast ratio PDS6101 700 : 1 (typ.)
Brightness 600 cd/m2(typ.)
Viewing angle Max. 160 degrees
Input Terminals
RS-232C D-sub 9 pin terminal
Color system
NTSC/PAL/SECAM/N-PAL/M-PAL
/4.43NTSC/PAL60
Display colors
16.7 million (256 each for R.G.B.)
Dimensions Width : 145.2cm (57.1 inch)
Height: 86.2cm (33.9 inch)
Depth : 11.9 cm (4.7 inch)
Net weight 61.0kg
Environment (Operating)
Temperature 0 to 40 C
Relative humidity 20 to 80%
Pressure 850 to 1,114 hPa
Accessories User's manual
Remote controller
Batteries (Type AA x 2)
Power cord
Big Ferrite core (2)
Small Ferrite core (2)
Options
Stand P-50TT01
Wall mounting unit
P-50WB01 installation angle
Horizontal 0 to 15
Vertical 0 to 5
Ceiling mounting unit P-50CT01 installation angle
Available 0 to 15
Standards
PDS6101W/E-H/S
AS
Safety : IEC950 A1/A2/A3/A4
EMC : AS/NZS 3548
CE
Safety: EN60950 1992
A1 1993
A2 1993
A3 1995
A4 1997
UL,CSA
Safety:
UL1950
CSA C22.2 No.950
EMC: FCC Part15 Class A
ICES-003 Class A
EMC : EN55022 A1/A2
Class A
EN61000-3-2, 1995
EN61000-3-3, 1995
EN55024 1998
EN61000-4-2, 1995
EN61000-4-3, 1996
EN61000-4-4, 1995
EN61000-4-5, 1995
EN61000-4-6, 1996
EN61000-4-8, 1993
EN61000-4-11,1994
Video input BNC connector
1.0VP-P /75Ω
S video input S terminal
Y signal:1.0VP-P /75Ω
C signal:0.286VP-P /75Ω
Component Three BNC terminals
video input Y : 1VP-P /75Ω
Pb/B-Y: 0.7VP-P /75Ω
Pr/R-Y: 0.7VP-P /75Ω
RGB 2 input mD-sub:15pin (3 row type)
Video : 0.7VP-P /75Ω
SYNC signal : TTL level
RGB 3 input BNC terminal x 5
R: 0.7VP-P/75Ω
G: 0.7VP-P/75Ω
B: 0.7VP-P/75Ω
H: TTL level or 0.3VP-P /75Ω
V: TTL level or 0.3VP-P /75Ω
User set mode 8 memories (each RGB1,2)
Display frequency Horizontal :15.63 to 80.0MHz
Vertical : 50.0 to 120Hz
Dot clock:50MHz Max
XGA 68MHz Max
RGB 1 input DVI-D terminal
Audio input 2 pin terminals(one system)
500mVrms/22kΩ
Effective max.
Level terminal 20W+20W (L/R), 4
Ω
output
SETTING SIGNALS
- 5 -
This display can store parameter settings for eight additional signals for RGB.
To do this, select the desired signal and follow "RGB MODE ADJUSTMENT" in the manual to adjust the parameters.
When you finish, the settings will be automatically stored.
FACTORY SET SIGNALS (RGB MODE)
Main corresponding signals (RGB mode)
* With some input signals, “Out of range” may appear even when the horizontal and vertical frequencies are within their permissible ranges. Make
sure that the vertical frequency of the input signal is 85 Hz or less for SVGA, 75 Hz or less for XVGA/ SXGA , 60 Hz or less for UXGA.
640 x 480 31.47 59.94 VGA
640 x 480 37.86 72.81 VGA 72 Hz
640 x 480 37.50 75.00 VGA 75 Hz
640 x 480 43.27 85.01 VGA 85 Hz
720 x 400 31.47 70.09 400 lines
800 x 600 37.88 60.32 SVGA 60 Hz
800 x 600 48.08 72.19 SVGA 72 Hz
800 x 600 46.88 75.00 SVGA 75 Hz
800 x 600 53.67 85.06 SVGA 85 Hz
1024 x 768 48.36 60.00 XGA 60 Hz
1024 x 768 56.48 70.07 XGA 70 Hz
1024 x 768 60.02 75.03 XGA 75 Hz
1280 x 1024 63.98 60.02 SXGA 60 Hz
1280 x 1024 79.98 75.03 SXGA 75 Hz
1600 x 1200 75.00 60.00 UXGA 60 Hz
1600 x 1200 106.25 85.00 UXGA 85 Hz
1600 x 1200 93.75 75.00 UXGA 75 Hz
640 x 480 35.00 66.67 MAC 13RGB
848 x 480 31.02 60.00
852 x 480 31.72 59.97
720 x 485 15.73 59.94 60 fields
720 x 575 15.63 50.00 50 fields
640 x 400 31.50 70.15 NEC 31 kHz
Signal DVD-I
Display (dots x lines) Horizontal frequency (kHz) Vertical frequency (Hz)
- 8 -
PART NAMES AND FUNCTIONS
Front
Power ON button [POWER ON]
Turns the power ON.
Power OFF button [POWER OFF]
Turns the power OFF.
RGB input mode selector button [RGB]
Switches between RGB input modes.
Video input mode selector button [VIDEO]
Switches between video input modes.
Wide screen selector button [WIDE]
Switches the screen over to a desired wide screen.
Menu button [MENU]
Use this button to display a desired menu for adjusting
the picture.
Volume adjustment buttons [VOL +/-]
Adjust the volume.
Press the + button to increase the volume.
Press the - button to reduce the volume.
Adjustment buttons [ / / / ]
Use these buttons to scroll through options in a menu
and change values.
Enter button [ENTER]
Press this button to finalize the selection of a desired
menu or option within a menu.
Display selector buttons [SHIFT 1-4]
When you use two or more displays, you can use
these buttons to control up to four displays by
assigning an unique number to each display.
ENTER
MENU
SHIFT
1
2
3
4
VIDEO
VOL
POWERON
RGB
POWEROFF
WIDE
ENTER
MENU
SHIFT
1
2
3
4
VIDEO
VOL
POWERON
RGB
POWEROFF
WIDE
ENTER
MENU
SHIFT
1
2
3
4
VIDEO
VOL
POWERON
RGB
POWEROFF
WIDE
ENTER
MENU
SHIFT
1
2
3
4
VIDEO
VOL
POWERON
RGB
POWEROFF
WIDE
Remote control
Power indicator lamp
This lamp shows the state of the power supply.
Lit (red): Power OFF (stand-by)
Lit (green): Power ON
Lit (orange): Power saving (DPMS: Power saving
function) mode ON
Flashing (red): Malfunction (Flashes differently depending
on the type of malfunction.
Remote control signal receiver
Receives signals from the remote control.
Power button
Turns the power ON or OFF (stand-by).
Input mode selector button [MODE]
Switches between picture input modes.
Wide screen selector button [WIDE]
Switches the screen over to a desired wide screen.
Menu button [MENU]
Displays picture adjustment menus.
Adjustment buttons [ / ]
The [ / ] buttons can also be used to scroll through the
options when a menu is displayed.
Adjustment buttons [ / ]
The [ / ] buttons can also be used to scroll through options
in a menu, or to change values.
Enter button [ENTER]
Press this button to finalize the selection of a desired option in
a menu.
10
10
- 12 -
TROUBLESHOOTING USING LED AND OSD
1. Display
(1) OSD
Two kinds of error messages are displayed on the screen, and the power is turned off 10 sec later.
(2) LED
LED error is displayed continuously after the power is turned off.
2. Error types and check points
On screen display Cause Check point
ERROR MESSAGE CONDITION 1 Fan protector operated Fan
Main power PCB
Main/Digital PCB
ERROR MESSAGE CONDITION 2 Temperature protector
operated Ambient temperature of unit
Main/Digital PCB
Temp. sensor IC757
(1) OSD
LED lamp display status Cause Check point
Steady light (Red) Stand-by status
Continuous
Flashes continuously (Red)
No power
Power supply protector
operated
Main power PCB
PDP panel
1 time
Flashes once every 4 sec. (Red) Fan protector operated
Fan
Main power PCB
Main/Digital PCB
2 times
Flashes twice every 5 sec. (Red) Temperature protector
operated
Ambient temperature of unit
Temperature sensor IC757
Main/Digital PCB
4 times
Flashes four times every 7 sec.
(Red)
Main/Digital circuit faulty Main/Digital PCB
5 times
Flashes five times every 8 sec.
(Red)
Video circuit faulty Video PCB Assy
(2) LED
--------------------
- 17 -
VSAND VdADJUSTMENT
When the Main Power Supply PCB and PDP panel are replaced, Vs and Vd must
be adjusted.
Adjustment time Within 3 minutes after power on.
Adjustment signal Adjust the Vs and Vd in the no-signal state.
Check points Refer to the drawing shown below.
Adjustment points Refer to the drawing shown below.
Adjustment value Within +/- 0.1V of voltage indicated on the label on the PDP panel.
RV3
Vs ADJ.
RV4
Vd AD J.
Vs & Vd check poin t
P6 1 pin Vs
2 pin Vs
4 pin Vd
5 pin GND
6 pin GND
1P6
P5 1
Main Power PCB (PFW-611)
- 19 -
DISASSEMBLY PROCEDURESDISASSEMBLY PROCEDURESDISASSEMBLY PROCEDURESDISASSEMBLY PROCEDURES
- 19 -
1.Removing the Rear Case
1)Remove the 35 circled screws and remove
the Rear Case.
* Layout of Main PCB.
A: Main Power PCB B: Main Digital PCB
C: Video PCB
D: Audio PCB
A
B
C
D
PARTS LIST
Ref.no. Description PDS6101W-H PDS6101E-H PDS6101W-S PDS6101E-S
Cabinet Case Front 8113312003 8113386004
Case Rear 8113294002
Electric Fan Motor 8900295007
Optical Filter 8113178005
Audio PCB Assy 8113276008
Connection PCB Assy 8113282009
I/O PCB Assy 8113284003
Key Switch PCB Assy 8113280005
LED/PHOTO PCB Assy 8113278002
Main Digital PCB Assy 8113102000
Video PCB Assy 8113274004
Main Power PCB Assy 8113268003
PDP Unit 8113269000
Noise Filter 0400222729
Power Cord UL.CSA 8112528009 ---------------- 8112528009 ----------------
VDE ---------------- 8112527002 ---------------- 8112527002
Remote Control Unit 8108442005 8110867001
Packing Carton Top 8113316001
Carton Bottom 8113317008
Packing Joint-D 8108655009
Packing Pad-Top 8113320008
Packing Pad-Bottom 8113321005
Carton Accessory 8111799004
: Same as left
- 60 -
TRANSPORTATION AND HANDLING RESTRICTIONS
Transportation
Don't load the plasmavision on a truck
as shown in the drawing.
Don't hold the
surface of the
optical filter.
Over 20 cm
Drop
Floor
Bad loading
Handling
Never drop.Never topple.
- 61 -
Don't stack the
plasmavision over
two units high.
Load the plasmavision as shown above.
Example of good transportation and handling
Good loading
3
2
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Fujitsu Monitor Handbücher
Fujitsu
Fujitsu B17-5 ECO Bedienungsanleitung
Fujitsu
Fujitsu Plasmavision PDS4213 Bedienungsanleitung
Fujitsu
Fujitsu proGREEN B20T-7 Bedienungsanleitung
Fujitsu
Fujitsu SCALEOVIEW C17-7 Bedienungsanleitung
Fujitsu
Fujitsu P24W-5 ECO Bedienungsanleitung
Fujitsu
Fujitsu FSC B17-1 Bedienungsanleitung
Fujitsu
Fujitsu SCENICVIEW A17-3 Bedienungsanleitung
Fujitsu
Fujitsu B22W-7 Bedienungsanleitung
Fujitsu
Fujitsu B24-9 TE Bedienungsanleitung
Fujitsu
Fujitsu B22W-6 LED Bedienungsanleitung
Fujitsu
Fujitsu Sl27T-1 Bedienungsanleitung
Fujitsu
Fujitsu A17-5 ECO Bedienungsanleitung
Fujitsu
Fujitsu P24-9 TE Bedienungsanleitung
Fujitsu
Fujitsu Plasmavision P42HHA10A Bedienungsanleitung
Fujitsu
Fujitsu P42XHA58E Series, P50XHA58E Series Bedienungsanleitung
Fujitsu
Fujitsu B27-9 TE FHD Bedienungsanleitung
Fujitsu
Fujitsu B19-6 LED Bedienungsanleitung
Fujitsu
Fujitsu Plasmavision PDS4201U Bedienungsanleitung
Fujitsu
Fujitsu Plasmavision PDS4221 Bedienungsanleitung
Fujitsu
Fujitsu SCALEOVIEW Q26W-1 Bedienungsanleitung
