Fujitsu D2785 Bedienungsanleitung

System Board D2785

for TX120 S2

Technical Manual

Edition April 2009

Comments…Suggestions…Corrections…

The User Documentation Department would like to

know your opinion of this manual. Your feedback helps

us optimize our documentation to suit your individual

needs.

Feel free to send us your comments by e-mail to

[email protected]ujitsu.com.

Certified documentation

according to DIN EN ISO 9001:2000

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system

which complies with the requirements of the standard

DIN EN ISO 9001:2000.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

D2785 (TX120 S2) Technical Manual

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 CE certificate of conformity . . . . . . . . . . . . . . . . . . 10

2.3 ENERGY STAR . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4 Environmental protection . . . . . . . . . . . . . . . . . . . 11

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.2 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.3 PCI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.4 Screen resolution . . . . . . . . . . . . . . . . . . . . . . . 18

3.5 Temperature / system monitoring . . . . . . . . . . . . . . . 19

3.6 Connectors and indicators . . . . . . . . . . . . . . . . . . 20

3.6.1 System board . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.6.2 Connector panel . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.6.3 Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4 Replacing the lithium battery . . . . . . . . . . . . . . . . . 27

Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

D2785 (TX120 S2) Technical Manual 5

1 Introduction

This technical manual describes the system board D2785, which is equipped

with one Intel®processor.

You will find further information in the manual “BIOS Setup”.

Further information about drivers is provided in the readme files on the hard

disk, or on the supplied CDs/DVDs.

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

Text in talics indicates commands or menu items.

Text in fixed font indicates system output on the monitor.

Text in semi-bold

fixed font

indicates values to be entered through the

keyboard.

[Key symbol] indicates keys according to their representation on

the keyboard.

If capital letters are to be entered explicitly, then the

Shift key is shown, e.g. [SHIFT] - [A] for A.

If two keys need to be pressed at the same time,

then this is shown by placing a hyphen between the

two key symbols.

“Quotation marks” indicate names of chapters and terms that are

being emphasized.

Êdescribes activities that must be performed in the

order shown.

VCAUTION! describes activities that must be performed in the

order shown.

Iindicates additional information, notes and tips.

Table 1: Notational conventions

D2785 (TX120 S2) Technical Manual 7

2 Important notes

In this chapter you will find essential information regarding safety when working

with the system board.

VCAUTION!

With the system board installed you must open the system to access the

system board. How to access the system board of your system is

described in the appropriate service supplement.

When handling the system board, refer to the specific notes on safety in

the operating manual and/or service supplement for the respective

server.

2.1 Notes on safety

VCAUTION!

●The actions described in these instructions should only be performed

by authorized, qualified personnel. Equipment repairs should only be

performed by qualified staff. Any failure to observe the guidelines in

this manual, and any unauthorized openings and improper repairs

could expose the user to risks (electric shock, fire hazards) and could

also damage the equipment. Please note that any unauthorized

openings of the device will result in the invalidation of the warranty

and exclusion from all liability.

●Transport the device only in the antistatic original packaging or in

packaging that protects it from knocks and jolts.

●Only install expansions that are allowed for the system board. If you

install other expansions, you may damage the requirements and rules

governing safety and electromagnetic compatibility or your system.

Information on which system expansions are suitable can be

obtained from the customer service centre or your sales outlet.

●The warranty expires if the device is damaged during the installation

or replacement of system expansions.

8 Technical Manual D2785 (TX120 S2)

Notes on safety Important notes

VCAUTION!

●Components can become very hot during operation. Ensure you do

not touch components when making extensions to the system board.

There is a danger of burns!

●Transmission lines to peripheral devices must be adequately

shielded.

●To the LAN wiring the requirements apply in accordance with the

standards EN 50173 and EN 50174-1/2. As minimum requirement

the use of a protected LAN line of category 5 for 10/100 MBps

Ethernet, and/or of category 5e for Gigabit Ethernet is considered.

The requirements of the specification ISO/IEC 11801 are to be

considered.

●Never connect or disconnect data transmission lines during a storm

(lightning hazard).

Batteries

VCAUTION!

●Incorrect replacement of lithium battery may lead to a risk of

explosion. The batteries may only be replaced with identical batteries

or with a type recommended by the manufacturer.

It is essential to observe the instructions in chapter “Replacing the

lithium battery”.

Modules with electrostatic-sensitive components

Boards with electrostatic sensitive devices (ESD) are marked with the following

label:

Figure 1: ESD label

D2785 (TX120 S2) Technical Manual 9

Important notes Notes on safety

When you handle components fitted with ESDs, you must observe the following

points under all circumstances:

●You must always discharge yourself of static charges (e.g. by touching a

grounded object) before working.

●The equipment and tools you use must be free of static charges.

●Shut-down the system and remove the power plug from the power socket

before inserting or removing boards containing ESDs.

●Always hold boards with ESDs by their edges.

●Never touch pins or conductors on boards fitted with ESDs.

●Use a grounding cable designed for this purpose to connect yourself to the

system unit as you install/deinstall the board.

●Place all components on a static-safe base.

IYou will find a detailed description for handling ESD components in the

relevant European or international standards (EN 61340-5-1,

ANSI/ESD S20.20).

Notes about boards

●During installation/deinstallation of the board, observe the specific instruc-

tions described in the service supplement for the respective server.

●Shut-down the system and remove the power plug from the power socket

before you make modifications on an installed board.

●To prevent damage to the board, the components and conductors on it,

please take great care when you insert or remove boards. Take great care

to ensure that extension boards are slotted in straight, without damaging

components or conductors on the board, or any other components, for

example EMI spring contacts

●Be careful with the locking mechanisms (catches, centring pins etc.) when

you replace the system board or components on it, for example memory

modules or processors.

●Never use sharp objects (screw drivers) for leverage.

10 Technical Manual D2785 (TX120 S2)

CE certificate of conformity Important notes

2.2 CE certificate of conformity

2.3 ENERGY STAR

The board complies with the requirements of the EC directives

2004/108/EC regarding “Electromagnetic Compatibility” and

2006/95/EC “Low Voltage Directive”. This is indicated by the CE

marking (CE = Communauté Européenne).

Compliance was tested in a typical PRIMERGY configuration.

In some particular configurations1the PRIMERGY TX120 S2 is

equipped with a power management system which, in energy-

saving mode, reduces the power consumption to <65 W. The

server thus satisfies the requirements of the U.S. Environmental

Protection Agency (EPA).

The EPA estimates that computer systems use around 5 % of all

electricity in the office sector and that this figure is growing

rapidly. If all computer systems and peripherals were placed in

energy-saving mode when not in use, the overall savings in

electricity could amount to some US $ 2 billion annually. These

savings would also prevent the emission of 20 million tons of

carbon dioxide into the atmosphere - equivalent to the emissions

from 5 million automobiles.

As an ENERGY STAR partner, Fujitsu Technology Solutions

GmbH has determined that in some particular configurations this

product meets the ENERGY STAR guidelines for energy

efficiency.

1These servers are always delivered with a particular setting in the BIOS setup. For details

please see the manual “D2785 BIOS Setup Utility for PRIMERGY TX120 S2” on the

PRIMERGY ServerView Suite DVD 2.

Inhaltsverzeichnis

Andere Fujitsu Hauptplatine Handbücher

Fujitsu

Fujitsu FLASH-CAN-48P Bedienungsanleitung

Fujitsu

Fujitsu PTM900 Bedienungsanleitung

Fujitsu

Fujitsu D2861 Bedienungsanleitung

Fujitsu

Fujitsu GA-8ISXT-FS P4 Titan Bedienungsanleitung

Fujitsu

Fujitsu D1271 Bedienungsanleitung

Fujitsu

Fujitsu D2860 Bedienungsanleitung

Fujitsu

Fujitsu D1837 Bedienungsanleitung

Fujitsu

Fujitsu D3034 Bedienungsanleitung

Fujitsu

Fujitsu MB 91F467 Bedienungsanleitung

Fujitsu

Fujitsu Siemens D1156 Bedienungsanleitung

Fujitsu

Fujitsu D2619-N Bedienungsanleitung

Fujitsu

Fujitsu F-Cue Bedienungsanleitung

Fujitsu

Fujitsu D2151 Bedienungsanleitung

Fujitsu

Fujitsu D2917 Bedienungsanleitung

Fujitsu

Fujitsu D2530 Bedienungsanleitung

Fujitsu

Fujitsu YOKOGAWA AF220 Montage- und Bedienungsanleitung

Fujitsu

Fujitsu MOTORKIT-91F267-MC Bedienungsanleitung

Fujitsu

Fujitsu D3030 Bedienungsanleitung

Fujitsu

Fujitsu MS-6191 Bedienungsanleitung

Fujitsu

Fujitsu MB39C026 Bedienungsanleitung

Fujitsu

Fujitsu D2679 Bedienungsanleitung

Fujitsu

Fujitsu Siemens D1160 Bedienungsanleitung

Fujitsu

Fujitsu D1527 Bedienungsanleitung

Fujitsu

Fujitsu SK-8FX-TSC-32PMC Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung