Fujitsu MAH3091MC - Enterprise 9.1 GB Hard Drive Bedienungsanleitung

C141-E103-02EN

MAH3182MC/MP SERIES

MAH3091MC/MP SERIES

MAJ3364MC/MP SERIES

MAJ3182MC/MP SERIES

MAJ3091MC/MP SERIES

DISK DRIVES

PRODUCT/MAINTENANCE MANUAL

C141-E103-02EN i

REVISION RECORD

Edition Date published Revised contents

01 Feb., 2000

02 Dec., 2000 As evaluation result, corrections have been added.

Specification No.: C141-E103-**EN

The contents of this manual is subject to

change without prior notice.

This page is intentionally left blank.

C141-E103-02EN iii

FOR SAFE OPERATION

Handling of This manual

This manual contains important information for using this product. Read thoroughly before using

the product. Use this product only after thoroughly reading and understanding especially the

section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully.

FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering

damage to their property. Use the product according to this manual.

(Proceed to the Copyright Page)

iv C141-E103-02EN

Related Standards

Specifications and functions of products covered by this manual comply with the following

standards.

Standard (Text) No. Name Enacting Organization

ANSI X3.131-1986 American National Standard for

Information Systems—Small Computer

System Interface (SCSI)

American National

Standards Institute

(ANSI)

ANSI X3.131-1994 American National Standard for

Information Systems—Small Computer

System Interface - 2(SCSI-2)

American National

Standards Institute

(ANSI)

X3T9.2/85-52 Rev 4.B COMMON COMMAND SET (CCS)

of the Small Computer

System Interface (SCSI)

American National

Standards Institute

(ANSI)

X3T9.2/855D Rev 12 WORKING DRAFT Information

Technology SCSI-3 Parallel Interface

American National

Standards Institute

(ANSI)

T10/1236-D Rev 12 WORKING DRAFT Information

technology SCSI Primary Commands-2

(SPC-2)

American National

Standards Institute

(ANSI)

ANSI NCITS 306-199x American National Standard for

Information Technology—SCSI-3 Block

Commands (SBC)

American National

Standards Institute

(ANSI)

X3T10/994D Rev 18 WORKING DRAFT Information

technology SCSI-3 Architecture Model

(SAM)

American National

Standards Institute

(ANSI)

T10/1302D Rev 11 WORKING DRAFT Information

technology SCSI Parallel Interface-3

(SPI-3)

American National

Standards Institute

(ANSI)

C141-E103-02EN v

PREFACE

This manual describes the MAH3182MC/MP, MAH3091MC/MP (hereafter, MAH series) and

MAJ3364MC/MP, MAJ3182MC/MP, MAJ3091MC/MP (hereafter, MAJ series), 3.5 type fixed disk drives

with an embedded SCSI controller.

This manual details the specifications and functions of the above disk drive, and gives the requirements and

procedures for installing it into a host computer system.

This manual is written for users who have a basic understanding of fixed disk drives and their use in

computer systems. The MANUAL ORGANIZATION section describes organization and scope of this

manual. The need arises, use the other manuals.

Chapter 1 GENERAL DESCRIPTION

This chapter introduces the MAH series and MAJ series disk drives and discusses their standard features,

hardware, and system configuration.

Chapter 2 SPECIFICATIONS

This chapter gives detailed specifications of the MAH series and MAJ series disk drives and their

installation environment.

Chapter 3 DATA FORMAT

This chapter describes the data structure of the disk, the address method, and what to do about media

defects.

Chapter 4 INSTALLATION REQUIREMENTS

This chapter describes the basic physical and electrical requirements for installing MAH series and MAJ

series disk drives.

Chapter 5 INSTALLATION

This chapter explains how to install MAH series and MAJ series disk drives. It includes the notice and

procedures for setting device number and operation modes, mounting the disk drive, connecting the cables,

and confirming drive operation.

Chapter 6 DIAGNOSIS and MAINTENANCE

This chapter describes the automatic diagnosis, and maintenance of MAH series and MAJ series disk drive.

This chapter also describes diagnostic methods for operation check and the basics of troubleshooting the

disk drives.

Chapter 7 ERROR ANALYSIS

This chapter describes in details how collect the information for error analysis and how analyze collected

error information.

Chapter 8 PRINCIPLE OF OPERATION

This chapter explains disk drives configuration and operation of MAH series and MAJ series.

vi C141-E103-02EN

APPENDIX A to D

The appendixes give supplementary information, including the locations of mounting setting terminals and

connectors, a list of setting items, the signal assignments of interface connectors, lists of model names and

product numbers, and SCSI interface functions.

The model numbers have a suffix that describes the electrical requirements of the SCSI interface between

host system and disk drive, the data formatted at the factory and device type.

CONVENTIONS

This manual uses the following conventions for alerts to prevent physical or property damages to users or

by standards.

DANGER

DANGER indicates that personal injury will occur if the user does not perform the procedure correctly.

WARNING

WARNING indicates that personal injury could occur if the user does not perform the procedure

correctly.

CAUTION

CAUTION indicates that either minor or moderate personal injury may occur if the user does not

perform the procedure correctly.

NOTICE

NOTICE indicates that inconvenience to the user such as damages to the product, equipment, data, and/or

other property may occur if the user does not pay attention or perform the procedure correctly.

IMPORTANT

IMPORTANT indicates information that the helps the user use the product more effectively.

Indicates

C141-E103-02EN vii

This manual indicates;

Decimal number: Indicates as it is.

Hexadecimal number: Indicates as X’17B9’, 17B9h, or 17B9H

Binary number: Indicates as “010”

DISCLAIMER

Failure of the MAH series and MAJ series intelligent disk drive is defined as a failure requiring

adjustments, repairs, or replacement. Fujitsu is not responsible for drive failures caused by misuse by the

user, poor environmental conditions, power trouble, host problems, cable failures, or any failure not caused

by the drive itself.

The suffix of the model name of the disk drive varies depending on the electrical requirements, capacity,

and data format at factory shipment of the SCSI, i.e., the interface for connecting the three device types or

host system and the disk drives (Note 1). However, in this manual, the typical model names (Note 2) are

used unless otherwise noted. These disk drives may be called intelligent disk drives (IDD), drives, or

devices in this manual.

Note 1: Model names

M AJ 3 364 MC

Interface types MC: LVD, 16-bit SCSI SCA2 connector 160MHz transfer

MP: LVD, 16-bit SCSI 68 pin connector 160MHz transfer

Formatted capacity (100 MB units)

Disk drive size 3: 3.5 type. Hand Disk Drive

Type AH: Number of rotations 7,200min-1 (7,200rpm)

AJ: Number of rotations 10,025min-1 (10,025rpm)

Note 2: Type model name

Type model name Model name

MAH3182 MAH3182MC, MAH3182MP

MAH3091 MAH3091MC, MAH3091MP

MAJ3364 MAJ3364MC, MAJ3364MP

MAJ3182 MAJ3182MC, MAJ3182MP

MAJ3091 MAJ3091MC, MAJ3091MP

viii C141-E103-02EN

Important Alert Items

Important Alert Messages

The important alert messages in this manual are as follows:

A hazardous situation could result in minor or moderate personal injury if the

user does not perform the procedure correctly. This alert signal also indicates

that damages to the product or other property may occur if the user does not

perform the procedure correctly.

Task Alert message Page

Mounting Installation Data loss

For MAH and MAJ series, Reed Solomon codes are applied for

their ECC.

The sector-data is divided into 4 interleaving sectors, and ECC is

performed in each sector where the maximum number of errors (up

to 5 byte) can be corrected. [Total maximum byte: 5 byte x 4 (

interleave) = 20 byte]

If the error of read sector keeps allowable error byte number,

correction is performed.

However, if error byte exceeds its allowable number, correction

may not be performed properly.

Hot temperature

To prevent injury, do not handle the drive until after the device has

cooled sufficiently after turning off the power. The DE and LSI

become hot during operation and remain hot immediately after

turning off the power.

Data loss

1. The user must not change the setting of terminals not described

in this section. Do not change setting status set at factory

shipment.

2. Do not change the setting of terminals except following setting

pins during the power is turned on.

• Write protect: CN2 9-10

3. To short the setting terminal, use the short plug attached when

the device is shipped from the factory.

Damage

1. Make sure that system power is off before connecting or

disconnecting cables.

2. Do not connect or disconnect cables when power is on.

Damage

1. Be careful of the insertion orientation of the SCSI connectors.

With the system in which terminating resistor power is supplied

via the SCSI cable, if the power is turned on, the overcurrent

2-5

5-1

5-5

5-11

C141-E103-02EN ix

Task Alert message Page

Mounting Installation protection fuse of the terminating resistor power supplier may

be blown or the cable may be burnt if overcurrent protection is

not provided.

When the recommended parts listed in Table 4.2 are used,

inserting the cables in the wrong direction can be prevented.

2. To connect SCSI devices, be careful of the connection position

of the cable. Check that the SCSI device with the terminating

resistor is the last device connected to the cable.

Data loss

When the SEND DIAGNOSTIC command terminates with the

CHECK CONDITION status, the INIT must collect the error

information using the REQUEST SENSE command. The RECEIVE

DIAGNOSTIC RESULTS command cannot read out the error

information detected in the self-diagnostics.

Caution

1. To avoid shocks, turn off the power before mounting or

removing a PCA, and before connecting or disconnecting a

cable, connector, or plug.

2. To avoid injury, do not touch the mechanical assembly during

disk drive operation.

3. Do not use solvents to clean the disk drive.

Caution

1. Always ground yourself with a wrist strap connected to ground

before handling. ESD (Electrostatics Discharge) may cause

the damage to the device.

2. To prevent electrical damage to the disk drive, turn the power

off before mounting or removing a PCA or connecting or

disconnecting a cable, connector, or plug.

3. Do not turn the power on while removing a PCA. This

operation is required to prevent unexpected or unpredictable

operation.

4. Do not use a conductive cleaner to clean a disk drive assembly.

5. Open all ventilation holes to prevent overheating of electric

circuits.

6. Ribbon cables are marked with a colored line. Connect the

ribbon cable to a cable connector with the colored wire

connected to pin 1.

Damage

Do not open the DE in the field because it is completely sealed.

Data loss

Save data stored on the disk drive before requesting repair. Fujitsu

does not assume responsibility if data is destroyed during servicing

or repair.

Caution

Never open the disk enclosure in the field. Opening the disk

enclosure in the field may cause an irreparable fault.

6-4

6-5

6-6

6-7

6-15

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Fujitsu Lagerung Handbücher

Fujitsu

Fujitsu HandyDrive-5 Bedienungsanleitung

Fujitsu

Fujitsu MBB2147RC SERIES Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS2000 200 Leitfaden

Fujitsu

Fujitsu MAP3147NC - Enterprise - Hard Drive Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS Multipath Driver V2 Bedienungsanleitung

Fujitsu

Fujitsu MAW3073 SERIES Bedienungsanleitung

Fujitsu

Fujitsu Eternus DX80 S2 Bedienungsanleitung

Fujitsu

Fujitsu FD-1100MT Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX S5 Series Leitfaden

Fujitsu

Fujitsu ETERNUS DX60 Referenzhandbuch

Fujitsu

Fujitsu ETERNUS DX S5 Series Installationsanleitung

Fujitsu

Fujitsu MHV2060AT Bedienungsanleitung

Fujitsu

Fujitsu C141-E282 Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS AF650 S2 Montageanleitung

Fujitsu

Fujitsu MAS3367FC Bedienungsanleitung

Fujitsu

Fujitsu GP5-HDH8B Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS LT20 S2 Anleitung zur Verwendung

Fujitsu

Fujitsu ETERNUS DX60 Bedienungsanleitung

Fujitsu

Fujitsu SLR 50 GBYTE Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS DX60 S3 Bedienungsanleitung

Fujitsu

Fujitsu MHN2100AT - Mobile 10 GB Hard Drive Bedienungsanleitung

Fujitsu

Fujitsu ETERNUS AF250 S2 Montageanleitung

Fujitsu

Fujitsu MAB3091FC Series Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

HP P9000 Bedienungsanleitung