Fujitsu MHA2021AT Bedienungsanleitung
C141-E042-01EN
MHA2021AT, MHA2032AT
DISK DRIVES
PRODUCT MANUAL
C141-E042-01EN
FOR SAFE OPERATION
Handling of This Manual
This manual contains important information for using this product. Read thoroughly before using
the product. Use this product only after thoroughly reading and understanding especially the
section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully.
FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering
damage to their property. Use the product according to this manual.
IMPORTANT NOTE TO USERS
READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO
USERS, BYSTANDERS OR PROPERTY.
While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU
assumes no liability to any party for any damage caused by any error or omission contained in this
manual, its updates or supplements, whether such errors or omissions result from negligence,
accident, or any other cause. In addition, FUJITSU assumes no liability with respect to the
application or use of any product or system in accordance with the descriptions or instructions
contained herein; including any liability for incidental or consequential damages arising therefrom.
FUJITSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION
CONTAINED HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.
FUJITSU reserves the right to make changes to any products described herein without further
notice and without obligation.
The contents of this manual may be revised without prior notice.
The contents of this manual shall not be disclosed in any way or reproduced in any media without
the express written permission of Fujitsu Limited.
All Rights Reserved, Copyright FUJITSU LIMITED 1997
C141-E042-01EN
Revision History
(1/1)
Edition Date Revised section (*1)
(Added/Deleted/Altered) Details
01 1997-07-15 — —
*1 Section(s) with asterisk (*) refer to the previous edition when those were deleted.
C141-E042-01EN i
Preface
This manual describes the MHA2021AT and MHA2032AT, 2.5-inch hard disk
drives. These drives have a built-in controller that is compatible with the ATA
interface.
This manual describes the specifications and functions of the drives and explains
in detail how to incorporate the drives into user systems. This manual assumes
that the reader has a basic knowledge of hard disk drives and their implementations
in computer systems.
This manual consists of seven chapters and sections explaining the special
terminology and abbreviations used in this manual:
Overview of Manual
CHAPTER 1 Drive Overview
This chapter gives an overview of the MHA2021AT and MHA2032AT and
describes their features.
CHAPTER 2 Drive Configuration
This chapter describes the internal configurations of the MHA2021AT and
MHA2032AT and the configuration of the systems in which they operate.
CHAPTER 3 Drive Installation
This chapter describes the external dimensions, installation conditions, and switch
settings of the MHA2021AT and MHA2032AT.
CHAPTER 4 Theory of Drive Operation
This chapter describes the operation theory of the MHA2021AT and
MHA2032AT.
CHAPTER 5 Interface Specifications
This chapter describes the interface specifications of the MHA2021AT and
MHA2032AT.
CHAPTER 6 Interface Operations
This chapter describes the operations of the MHA2021AT and MHA2032AT.
CHAPTER 7 Miscellaneous
This chapter describes how to reformat the MHA2021AT and MHA2032AT.
Terminology
This section explains the special terminology used in this manual.
Preface
ii C141-E042-01EN
Abbreviation
This section gives the meanings of the definitions used in this manual.
Conventions for Alert Messages
This manual uses the following conventions to show the alert messages. An alert
message consists of an alert signal and alert statements. The alert signal consists
of an alert symbol and a signal word or just a signal word.
The following are the alert signals and their meanings:
This indicates a hazarous situation could result in
minor or moderate personal injury if the user does
not perform the procedure correctly. This alert
signal also indicates that damages to the product or
other property, may occur if the user does not
perform the procedure correctly.
This indicates information that could help the user
use the product more efficiently.
In the text, the alert signal is centered, followed below by the indented message. A
wider line space precedes and follows the alert message to show where the alert
message begins and ends. The following is an example:
(Example)
Data corruption: Avoid mounting the disk drive near strong
magnetic sources such as loud speakers. Ensure that the disk drive is
not affected by external magnetic fields.
The main alert messages in the text are also listed in the “Important Alert Items.”
Operating Environment
This product is designed to be used in offices or computer rooms.
For details regarding the operating environment of use, refer to the
(Cnnn-Xnnn) and the
(Cnnn-Xnnn).
Attention
Please forward any comments you may have regarding this manual.
Preface
C141-E042-01EN iii
To make this manual easier for users to understand, opinions from readers are
needed. Please write your opinions or requests on the Comment at the back of this
manual and forward it to the address described in the sheet.
Liability Exception
“Disk drive defects” refers to defects that involve adjustment, repair, or
replacement.
Fujitsu is not liable for any other disk drive defects, such as those caused by user
misoperation or mishandling, inappropriate operating environments, defects in the
power supply or cable, problems of the host system, or other causes outside the
disk drive.
C141-E042-01EN v
Important Alert Items
Important Alert Messages
The important alert messages in this manual are as follows:
A hazardous situation could result in minor or moderate personal
injury if the user does not perform the procedure correctly. Also,
damage to the predate or other property, may occur if the user does
not perform the procedure correctly.
Task Alert message Page
Normal Operation Data corruption: Avoid mounting the disk near strong
magnetic soures such as loud speakers. Ensure that the disk
drive is not affected by extrnal magnetic fields.
3-6
C141-E042-01EN vii
Contents
CHAPTER 1 Device Overview .......................................................................1-1
1.1 Features 1-2
1.1.1 Functions and performance 1-2
1.1.2 Adaptability 1-2
1.1.3 Interface 1-2
1.2 Device Specifications 1-4
1.2.1 Specifications summary 1-4
1.2.2 Model and product number 1-5
1.3 Power Requirements 1-5
1.4 Environmental Specifications 1-7
1.5 Acoustic Noise 1-7
1.6 Shock and Vibration 1-8
1.7 Reliability 1-8
1.8 Error Rate 1-9
1.9 Media Defects 1-9
CHAPTER 2 Device Configuration................................................................2-1
2.1 Device Configuration 2-2
2.2 System Configuration 2-4
2.2.1 ATA interface 2-4
2.2.2 1 drive connection 2-4
2.2.3 2 drives connection 2-5
Contents
viii C141-E042-01EN
CHAPTER 3 Installation Conditions..............................................................3-1
3.1 Dimensions 3-2
3.2 Mounting 3-3
3.3 Cable Connections 3-7
3.3.1 Device connector 3-7
3.3.2 Cable connector specifications 3-8
3.3.3 Device connection 3-8
3.3.4 Power supply connector (CN1) 3-9
3.4 Jumper Settings 3-9
3.4.1 Location of setting jumpers 3-9
3.4.2 Factory default setting 3-10
3.4.3 Master drive-slave drive setting 3-10
3.4.4 CSEL setting 3-11
CHAPTER 4 Theory of Device Operation......................................................4-1
4.1 Outline 4-2
4.2 Subassemblies 4-2
4.2.1 Disk 4-2
4.2.2 Head 4-2
4.2.3 Spindle 4-3
4.2.4 Actuator 4-3
4.2.5 Air filter 4-3
4.3 Circuit Configuration 4-4
4.4 Power-on Sequence 4-6
4.5 Self-calibration 4-7
4.5.1 Self-calibration contents 4-7
4.5.2 Execution timing of self-calibration 4-8
4.5.3 Command processing during self-calibration 4-9
4.6 Read/write Circuit 4-9
4.6.1 Read/write preamplifier (PreAMP) 4-9
4.6.2 Write circuit 4-10
Contents
C141-E042-01EN ix
4.6.3 Read circuit 4-12
4.6.4 Time base generator circuit 4-13
4.7 Servo Control 4-14
4.7.1 Servo control circuit 4-14
4.7.2 Data-surface servo format 4-18
4.7.3 Servo frame format 4-18
4.7.4 Actuator motor control 4-19
4.7.5 Spindle motor control 4-20
CHAPTER 5 Interface..................................................................................... 5-1
5.1 Physical Interface 5-2
5.1.1 Interface signals 5-2
5.1.2 Signal assignment on the connector 5-2
5.2 Logical Interface 5-6
5.2.1 I/O registers 5-6
5.2.2 Command block registers 5-8
5.2.3 Control block registers 5-13
5.3 Host Commands 5-13
5.3.1 Command code and parameters 5-14
5.3.2 Command descriptions 5-16
5.3.3 Error posting 5-67
5.4 Command Protocol 5-69
5.4.1 Data transferring commands from device to host 5-69
5.4.2 Data transferring commands from host to device 5-71
5.4.3 Commands without data transfer 5-73
5.4.4 Other commands 5-74
5.4.5 DMA data transfer commands 5-74
5.5 Timing 5-76
5.5.1 PIO data transfer 5-76
5.5.2 Single word DMA data transfer 5-78
5.5.3 Multiword DMA data transfer 5-79
5.5.4 Power-on and reset 5-79
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Fujitsu Lagerung Handbücher
Fujitsu
Fujitsu ETERNUS DX Disk Bedienungsanleitung
Fujitsu
Fujitsu MBA3300 NP SERIES Bedienungsanleitung
Fujitsu
Fujitsu Eternus DX200F Bedienungsanleitung
Fujitsu
Fujitsu ETERNUS DX8100 S4 Technisches Handbuch
Fujitsu
Fujitsu PG-HDH97A Bedienungsanleitung
Fujitsu
Fujitsu Eternus CS800 S3 Bedienungsanleitung
Fujitsu
Fujitsu ETERNUS LT140 Bedienungsanleitung
Fujitsu
Fujitsu MHU2100AT Bedienungsanleitung
Fujitsu
Fujitsu MPF3XXXAH Bedienungsanleitung
Fujitsu
Fujitsu ETERNUS DX80 Bedienungsanleitung
Fujitsu
Fujitsu MAN3184 SERIES Bedienungsanleitung
Fujitsu
Fujitsu MPA3017AT Bedienungsanleitung
Fujitsu
Fujitsu MAN3184MC - Enterprise 18.4 GB Hard Drive Bedienungsanleitung
Fujitsu
Fujitsu DynaMO 640SZI Bedienungsanleitung
Fujitsu
Fujitsu MPF3102AT - Desktop 10.2 GB Hard Drive Bedienungsanleitung
Fujitsu
Fujitsu FD-1100MT Bedienungsanleitung
Fujitsu
Fujitsu MHW2160BJ Bedienungsanleitung
Fujitsu
Fujitsu MAT3300NC/NP Product/ Bedienungsanleitung
Fujitsu
Fujitsu ETERNUS DX60 S2 Bedienungsanleitung
Fujitsu
Fujitsu Eternus CS800 S2 Bedienungsanleitung
Beliebte Lagerung Handbücher anderer Marken
Spectra Logic
Spectra Logic T-Series Spectra T50e Bedienungsanleitung
Panasonic
Panasonic LKM-F931-1 Bedienungsanleitung
Tabernus
Tabernus Enterprise Erase E2400 Bedienungsanleitung
Rocstor
Rocstor COMMANDER 3F series Bedienungsanleitung
HP
HP P9000 Bedienungsanleitung
Western Digital
Western Digital Ultrastar Data60 Bedienungsanleitung