Furrion FACR14SA-BL-AM Bedienungsanleitung

User Manual of Product 1:

Furrion FACR14SA-BL-AM RV Air Conditioner, 14.5K BTU,

Black

FACT11MA-PS/FACT11MA-BL

(Sold Separately)

Rooftop Air Conditioner

Instruction Manual

Model:

FACR13SA-PS/FACR13SA-BL

FACR14SA-PS/FACR14SA-BL

FACR15SA-PS/FACR15SA-BL

Contents

Thank you for purchasing this Furrion® ChillTM Rooftop Air Conditioner.. Before

operating your new product, please read these instructions carefully. This will ensure

safe use and reduce the risk of injury. This instruction manual contains information for

installation, operation, maintenance of the product and safe use.

Please keep this instruction manual in a safe place for future reference. Be sure to pass

on this manual to any new owners of this product.

The manufacturer does not accept responsibility for any damages due to not

observing these instructions.

Contents ...................................................................................................................... 1

Important Safety Instructions.................................................................................. 2

Handling the device.............................................................................................................................2

Handling Electrical Cables...............................................................................................................3

Before Installing ......................................................................................................... 4

What’s in the Box...................................................................................................................................4

Choosing Proper Location for the Air Conditioner................................................................4

Roof Preparation...................................................................................................................................6

Air Distribution Duct Sizing and Design......................................................................................7

Air Distribution System Installation...............................................................................................8

Laying the Connecting Cables .......................................................................................................9

Installation .................................................................................................................. 10

Installing the Rooftop Unit.................................................................................................................10

Installing the Air Distribution Box (for FACT11MA-PS/FACT11MA-PS models only,

same for both ducted and non-ducted models, sold separately)...................................10

Operation..................................................................................................................... 14

Change the Operating Mode...........................................................................................................14

Set the Temperature............................................................................................................................14

Defrosting & Anti-Freezing Instructions .....................................................................................14

Cleaning and Maintenance ...................................................................................... 16

Troubleshooting ......................................................................................................... 17

Specifications............................................................................................................. 18

Wiring Diagram ........................................................................................................... 19

Important Safety Instructions

This manual has safety information

and instructions to help users eliminate

or reduce the risk of accidents and

injuries. Please read this instruction

manual carefully before installation

and start-up, and store it in a safe place

for future reference. If you pass on the

device to another person, hand over this

instruction manual along with it.

●The manufacturer accepts no liability

for damage in the following cases:

−Faulty assembly or connection

−Damage to the product resulting from

mechanical influences and excess

voltage

−Alterations to the product without

express permission from the

manufacturer

−Use for purposes other than those

described in the operating manual

●The following basic safety information

should be heeded when using

electrical devices to protect against:

−Electric shock

−Fire hazards

−Injury

●All Furrion product referenced in

this manual is to be installed in

accordance with local and national

codes, including the latest editions of

the following standards:

USA:

−NFPA 1192

−NFPA 70

Canada:

−C22.1

−CSA Z240

Handling the device

WARNING

●Installation and repair of the rooftop

air conditioner must only be carried

out by qualified personnel who are

familiar with the risks involved and

the relevant regulations. Inadequate

repairs may cause serious hazards.

●Electrical devices are not toys.

Keep electrical devices out of reach

of children or elderly persons. Do

not allow them to use electrical

devices without supervision.

●Prevent inexperienced people

from using the device without

supervision.

●Do not undo the upper cover

of the rooftop air conditioner in

the event of a fire. Use approved

extinguishing agents instead. Do

not use water to extinguish fires.

CAUTION

●The rooftop air conditioner must be

installed securely so that it cannot

fall down.

●Only operate the rooftop air

conditioner if you are certain that

the housing and the cables are not

damaged.

●Do not use the rooftop air

conditioner near flammable fluids or

in closed rooms.

●Make sure no combustible objects

are stored or installed near the air

outlet. A distance of at least 20”

must be kept.

●Do not reach into air outlets or

insert any foreign objects into the

device.

●Only use the device as intended.

●Do not make any alterations or

conversions to the device.

●If faults occur in the refrigerant

circuit, the system must be checked

by a certified service technician and

repaired properly. The refrigerant

must never be released into the air.

Handling Electrical

Cables

WARNING

The electrical power supply must only

be connected by a qualified electrician.

CAUTION

●Refer to NEC (National Electric

Code) for proper sizing of wire

gauge (awg) based on cable length

and overcurrent protection rating

that is suppling power to the air

conditioner.

●See rooftop unit nameplate for

proper overcurrent protection

sizing.

●Attach and lay the cables so that

they cannot be tripped over or

damaged.

●Only a qualified electrician should

connect the rooftop air conditioner to

electrical power.

●Do not lay loose or bent cables next

to electrically conductive materials.

●Do not pull on the cables.

●Use cable ducts to lay cables through

walls with sharp edges.

●Refer to rooftop unit nameplate and

NEC for proper power supply rating.

Before Installing

Read this installation manual completely

before installing the rooftop air

conditioner.

The following tips and instructions must

be observed while installing the rooftop

air conditioner.

What’s in the Box

Open and remove the components

from carton. Make sure you have all

the following items included in the

packaging, if any item is missing, contact

your dealer.

Rooftop Air Conditioner:

Rooftop Unit

Mounting Frame

Filter

Decoration Plate

ADB Shroud

Control Box

Bolt

Control Knob

Lower Duct

Divider

Upper Duct

Divider

PE Foam

●Rooftop unit x 1

●Warranty Leaflet x 1

Air Distributor Box (sold separately):

Rooftop Unit

Mounting Frame

Filter

Decoration Plate

ADB Shroud

Control Box

Bolt

Control Knob

Lower Duct

Divider

Upper Duct

Divider

PE Foam

●Upper Duct Divider x 1

●Lower Duct Divider x 1

●Bolt x 4

●Mounting Frame x 1

●Control Box x 1

●Air Distribution Box (ADB) Shroud x 1

●Filter x 2

●Decoration Plate x 1

●PE Foam x 1

●Control Knob x 2

●Self-tapping Screws x 4

●Instruction Manual x 1

●Warranty Leaflet x 1

Choosing Proper Location

for the Air Conditioner

IMPORTANT: The roof must be

designed to support the weight of the

rooftop unit and the weight of 2 installers

standing on the roof.

There are two ways of installing the

rooftop air conditioner:

●Using the existing roof vent opening in

the vehicle roof.

●Making a new opening. In this case

the opening should be reinforced by

an appropriate frame as required.

Existing Roof Vent Opening

The air conditioner is designed to fit over

an existing 14” roof vent opening.

New Opening

When no roof vent is available or another

location is desired, the following is

recommended:

●For one unit installation - the air

conditioner should be mounted

slightly forward of center (front to

back) and centered from side to side.

●For two unit installations, install one

air conditioner one third from the front

of the RV and the other air conditioner

two thirds from the front of the RV,

aligned in the center.

It is preferred that the air conditioner be

installed on a relatively flat and horizontal

roof section measured when the RV is

parked on a level surface.

NOTE: A 15° slant to either side or front

to back is acceptable for all units. If the

roof exceeds 15° please use an exterior

leveling shim to make air conditioner

level.

After the Location Has Been

Selected:

●Check for obstructions in the area

where the air conditioner will be

installed.

Center Line

of Rooftop

Front

Roof Opening

18”

34⁄”

(884mm)

13⁄”

(345mm)

27⁄”

(700mm)

Keep this air flow area free of obstructions

●Check the inside of the RV for

return air kit obstructions. (i.e. door

openings, room dividers, curtains,

ceiling fixtures, etc.) Allow 6”

(152mm) space from the opening to

account for any potential return air kit

obstructions.

Roof

Opening

19⁄”

(500mm)

19⁄”

(500mm)

2⁄”

(70mm)

19⁄”

(500mm)

19⁄”

(500mm)

Roof Preparation

Opening Requirements - Before

preparing the ceiling opening, decide

on the type of system options. Read

all of the following instructions before

beginning the installation.

WARNING

Fire/Electric Shock Hazard

●Make sure there are no obstacles

inside the RV roof, floor and walls,

such as wires and pipes.

●Shut off the gas supply and

disconnect the 115VAC power from

the RV before drilling or cutting

into the RV. Failure to obey these

warnings could result in death or

serious injury.

Roof Thickness

The installation of air conditioner suits

for roof thickness from 3.5” (90mm) to

6” (152mm). For other thickness, please

contact Furrion or Furrion authorized

service agent.

Installing in an Existing

Opening

1. Unscrew and remove the roof vent.

2. Remove all caulking compound

around the opening.

3. If the opening exceeds 14¼” x 14¼”

(+½”), it will be necessary to resize the

opening to 14¼” x 14¼” (+½”). If the

opening is less than 14¼” x 14¼” (+½”),

it must be enlarged.

362mm

14¼”

362mm

14¼”

362mm

14¼”

362mm

14¼”

Making a New Opening

If a roof vent opening will not be used,

a 14¼” x 14¼” (+½”) (362mm x 362mm)

opening must be cut through the roof

and ceiling of the RV. This opening must

be located between the roof reinforcing

members.

The 14¼” x 14¼” (+½”) opening is

part of the return air system of the air

conditioner and must be finished in

accordance with NFPA Standard 501C

Section 2.7.2.

1. Mark a 14¼” x 14¼” (+½”) square on

the roof and carefully cut an opening.

362mm

14¼”

362mm

14¼”

362mm

14¼”

362mm

14¼”

2. Using the roof opening as a guide, cut

a matching hole in the ceiling.

NOTE: Maintain structural integrity.

Otherwise damage to product and/or

RV could occur. Always observe the

following guidelines while structuring

the opening.

Do not cut roof

structure or

rafters

Good: rafters

supported by

cross beams

Good: location

between roof

rafters

3⁄4" Min.

(19.05 mm)

Leave access for

power supply wiring

3. The opening created must be framed

to provide adequate support and

prevent air from being drawn from the

roof cavity.

4. Lumber ¾” or more in thickness must

be used. Remember to provide an

entrance hole for power supplies,

wall thermostat and furnace wiring

for connections. Leave 15” (381mm)

minimum at the front of the opening.

Do not cut roof

structure or

rafters

Good: rafters

supported by

cross beams

Good: location

between roof

rafters

3⁄4" Min.

(19.05 mm)

Leave access for

power supply wiring

Air Distribution Duct

Sizing and Design

The installer of this system must design

the air distribution system for their

particular application.

NOTE: Make sure ductwork will NOT

bend or collapse during and after

installation, and that it is correctly

insulated and sealed. Otherwise, damage

to roof structure and ceiling could occur.

The following requirements must be met

for properly operate the unit:

Roof Cavity

Depth 3”-6” (75mm-152mm)

Duct Cross

Sectional Area 21 Sq. In. Min.

Duct Size

Depth

1½” Min. - 2½”

Max. (38mm

Min. - 63.5mm

Max.)

Width

7” Min. - 10” Max.

(178mm Min. -

254mm Max.)

Total Duct

Length

15Ft. Min. - 40Ft.

Max. (4.5m -

13m)

Duct Length

(short run)

⅓ Total Duct

Length

Requirements

per A/C Unit

Number

Required 4 Min. - 8 Max.

Supply Register

Free Air Area

14 Sq. In. (90 sq.

cm)

Return Register

Free Air Area

40 Sq. In. (258

sq. cm)

Distance From

Duct End

5” Min. - 8” Max.

(127mm Min. -

203mm Max.)

Distance From

Elbow 15” (381mm)

Total System

Static Air

Pressure

Blower at High

Speed, Filter &

Grille In Place

0.55 - 1.10 In.

W.C.

●Properly insulate and seal all

discharge air ducts to prevent

condensation from forming on their

surfaces or adjacent surfaces during

operation of the unit. This insulation

must be R-7 minimum.

Frame

DuctDuct

Frame

Roof

Opening

Roof Opening

Roof

SIDE VIEW

(TOWARD BACK OF RV)

Duct Ceiling Duct

TOP VIEW

(BACK OF RV)

●Return air openings must have

80 square inches (516 square

centimeters) minimum free area

including the filter.

●Return air to the unit must be filtered

to prevent dirt accumulation on the

unit cooling surface.

Air Distribution System

Installation

It is the responsibility of the installer to

review each RV floor plan to determine

the following items in conjunction with

“Air Distribution Duct Sizing and Design”

section on Page 8.

NOTE: Alternate configurations and

methods may be used which will allow

the unit to operate properly, however,

these alternate configurations and

methods MUST be approved by Furrion

in writing.

●Duct size

●Duct layout

●Register size

●Register location

●Thermostat location

●Indoor temperature sensor location (if

applicable)

Front

Registers 4

Min - 8 Max.

(Per Unit) 14

Sq. In. Free

Area Per

Air Conditioner

Return Air

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Furrion Klimaanlage Handbücher

Furrion

Furrion CHILL FACR13LPSA-PS Bedienungsanleitung

Furrion

Furrion Chill FACR13SA-PS Bedienungsanleitung

Furrion

Furrion FACT12LA-PS Bedienungsanleitung

Furrion

Furrion FACR15SA-BL-AM Bedienungsanleitung

Furrion

Furrion FACB09HM Bedienungsanleitung

Furrion

Furrion FACR09SM-PS Bedienungsanleitung

Furrion

Furrion CHILL FACR13HESA Series Bedienungsanleitung

Furrion

Furrion Chill AC-FACR15SA-PS-AM Bedienungsanleitung

Furrion

Furrion Chill FACR13SA-PS Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung