Furuno NavNet TZtouch3 Series Bedienungsanleitung

Installation

Checklist

TZtouch3 Installation Checklist

MFD Network Installation

Connect all TZtouch3 MFDs to the Ethernet Network. If a HUB101 is used, set the

internal HUB101 DIP switches to OFF (HUB101 DIP Switches are OFF by Default). Please

see

Appendix

for more detailed information.

Connect all TZtouch3 MFDs to a proper NMEA2000 backbone using drop cables (18 feet

or less).

Note: TZtouch3 MFDs do not have an internal terminating resistor that can be switched

ON or OFF. All connections to the NMEA2000 backbone must be “drop” connections (18

feet or less).

Pick one TZtouch3 MFD as the Chart Master and select “ON” for “Chart Master Device”

setting from the “Initial Setup” menu. You will notice that a System ID is generated on

the TZT3 that is designated as the Chart Master and all other TZT3(s) on the network

will assume the same exact System ID. The MFD that you pick to be the Chart Master

should be a unit that is always turned on and left on during operation. However, if you

are adding TZT3 MFD(s) to an existing TZT2 network that has pay for charts unlocked

you will leave the “Chart Master Device”setting OFF on the TZT3 MFD(s) because the

TZT3 MFD(s) will assume the System ID of the current TZT2 Chart Master.

If chart unlock code(s) have been purchased for the Chart Master’s System ID, you can

enter unlock code(s) to unlock your purchased charts. On the Home page you can select

“Chart” and press on “Insert Unlock Code” on the top of the page and enter the unlock

code(s) when prompted. Note, unlock codes are hexadecimal so you will never have the

letter “O” only the number zero “0”.

If using an external sounder, make sure the DFF1, BBDS1, DFF3, and DFF1-UHD are set

up for “Static IP”. Please see

Appendix

for more detailed information.

Power ON the Ethernet HUB/Switch, NMEA2000 backbone, sensors, then start the

TZtouch3 MFDs.

If a Sirius Satellite Weather Receiver is installed (BBWX3 or BBWX4), set the “Weather

Data Server” to “Sirius” from the “Weather” menu.

Once the TZtouch3 MFDs have started, press the “Home” button, select “Menu” on each

MFD to confirm that you see both a “Radar”and “Fish Finder”menu as well as confirm

the “Radar Source” and “Fish Finder Source” is set appropriately (assuming you have

both a sounder and radar connected to the Ethernet Network).

oConfirm all Ethernet and NMEA2000 devices are detected by pressing the “Sensor

List” button in the “Initial Setup” menu. All detected devices are bright white, while

devices that are no longer seen will be designated in light gray (Press “Reset”

button on top right of the screen to refresh list). Take the time ensure no

Instancing Conflicts exist. Device Instances can be edited by pressing on Keyboard

Icon. Any sensor that outputs the same information should have a different

Instance Number (Priority). For example, if you have a PG700 and an SCX20 on

the NMEA2000 backbone, set the Instance Number of the SCX20 to (0) and the

PG700 to (1). Zero (0) is the lowest number and is the higher priority.

oIf you are missing the option to select your sounder model as the “Fish Finder

Source” under the “Fish Finder” menu, make sure that the

DFF1/BBDS1/DFF3/DFF1-UHD sounder DIP Switch/Mode Switch settings are

correct and that you see good traffic on the Ethernet port (blinking green light).

See

Appendix

for more detailed information.

oIf you are missing the Radar menu and your radar was/is an original NavNet 3D

DRS2D,DRS4D,DRS4A,DRS12A or DRS25A ensure light on the PSU (depending on

the model of DRS, either a PSU017 or a PSU012.) is on, if not ensure Jumper is

inserted to bypass Power Synch. If power supply is on and still no communication

with DRS radar, ensure DRS software was updated to 1.16 or higher. Please see

Appendix

for more detailed information.

oNote that there is no need to restart the TZT3 MFDs to have the Sounder and/or

Radar appear in the menu. As soon as the radar or sounder are detected on the

network, they will automatically update and appear in real time.

Select the “Radar”menu and the select your radar model number under “Radar Source”.

Scroll down to the “Radar Initial Setup” to adjust, at minimum the following parameters:

oHeading Alignment

oAntenna Height

Select the “Sounder”menu and the select your sounder model number under “Sounder

Source”. Scroll down to “Sounder Initial Setup” to adjust at minimum the following

parameters:

oDraft

oTransducer

If you have a Fusion radio(s) installed confirm you have a “Fusion” menu selection on

the Home screen. If not, ensure you have connected the Fusion radio via LAN (Ethernet)

and not NMEA2000 and have followed our instructions on furunousa.com concerning IP

and Subnet configuration of the Fusion radio(s). Click on the following link to access

Fusion Link information. Fusion Link Setup

If you have Axis IP Cameras or Axis Video Servers but you do not have the option to

select them as a video source or, you only see a “Video Decoding Error” message on the

screen for the video source that is selected. Ensure you have set them up correctly as

per our documentation. Click on the following link to for detailed information. AXIS IP

Camera and Video Server Setup

If you have a CZONE interface but you notice you do not have CZONE as an option

under “Graphic Instrument Setup”found in the “Initial Setup”menu. Ensure you have

set up the interface correctly per our documentation. Click on the following link to for

detailed information. CZONE Setup

If you have NMEA2000 engine interface(s), initiate the automatic engine setup option by

selecting “Engine and Tank Automatic Setup” found under the “Initial Setup” menu.

If you have an SCX20 and/or SC33 use the “Sensor Management” menu found under

“Initial Setup” to perform installation settings, adjustments, offsets, change NMEA2000

output settings, and self-tests as needed.

Select the NMEA2000 PGNs that you want to output on the NMEA2000 backbone from

the “PGN Output” button of the “Initial Setup” menu.

Note: The PGN output configuration is a global setting to the system (the PGN output

settings are shared among all the TZtouch3 MFDs). However, only one MFD will actually

output data on the NMEA2000 bus (the one that was first powered ON). If that MFD is

turned OFF or fails, another TZtouch3 MFD will automatically replace it and start

outputting the same PGNs onto the NMEA2000 backbone. Do not turn on every PGN.

Only turn on the PGN(s) that are needed for other pieces of equipment on the

NMEA2000 network. If you have an Autopilot connected, you would normally turn on

PGN 129025,026,029,033,283,284 and 129285.

Select the “Preferred” data/sensor sources for the network by pressing the “Data

Source” button in the “Initial Setup” menu.

Select your preferred units of measurement such as Foot, Meters, Celsius, Fahrenheit,

etc. from the “Units” menu.

Ensure that you have set the appropriate “Local Time Offset”value under the “General”

menu or the time displayed will be incorrect.

Mixed TZ

touch2 and TZtouch3

Network Installations



TZtouch2 MFD(s) must have software version 7.0 or higher.

If any “For pay charts”

were purchased for the TZT2 system, keep that unit as the chart master. All other

MFD(s) Chart Master setting should be turned off (default).

If you have a TZT3(s) mixed network with TZT2(s), one TZT2 will be a Chart Master. If

there is an existing TZT2 Chart Master, leave it as the Chart Master. You will notice the

TZT3 will assume the System ID of the master TZT2 in the network. The MFD that you

pick to be the Chart Master should be a unit that is always turned on and left on.

Recommend Customizations

You can set parameters for Tracks under the “Ship & Track” menu. Typically, the “Track

Interval” is either set for “Time” or “Distance” however, there are other options

available. For example, recording tracks by “Depth”, “SST” (Sea Surface Temperature) or

“Bottom Discrimination”.

Increasing the “Chart Object Size” (Names, Symbols, Sounding Depth Numbers etc..)

especially Sounding Depth Numbers can very helpful. This setting is found in the “Vector

Chart” menu.

You can adjust the time in which user interface objects such as pop up information, data

boxes or menus remain open before they “Auto-Hide”, you can set a longer dwell time

by increasing the “User Interface Auto-Hide” value. This setting is found in the “General”

menu. Options are:

o3 sec

o5 sec

o10 sec (Default)

o15 sec

You can choose to increase the size of font, data boxes and the menu(s) . The “Scale &

Layout” setting is found under the “General” menu. You have the following options:

oSmallest

oSmall

oNormal

oLarge

Customize your Data Boxes simply by performing a left edge swipe from the left-hand side

of the MFD. You can reorganize the preset data boxes by tapping and holding anywhere

in the databox area. You can use the grip symbol (drag and drop) or you can completely

customize the data box environment by deleting/changing presets and selecting the type

of data display (Numeric or Graphic) and type of data (Navigation, Radar, Waypoint etc..).

The “Two Finger Tap Function” and “Two Finger Long Tap Function” settings is are

found in the “General” menu. These settings help create a quick and easy way to access

menus and/or functions by simply taking two fingers and quickly tapping on the screen

or taking two fingers tap then hold. The following are available menus/functions:

oFull Screen (Default Two Finger Tap)

oScreen Capture

oEvent Mark

oHome (Default Two Finger Long Tap)

oSettings

oLists

oTides

Your Instrument page has several preset pages such as Sailing, Cruising, Highway,

Inboard and Outboard engines, etc. You can choose to rename, edit, delete or add data

on these preset pages, or you can delete the preset pages altogether and create your

own customized page simply by adding a New Page and selecting the type of

instruments and data you want to display.

Create boundaries and alarms to notify you of known protected or prohibited areas. Tap

on the screen select “New Boundary”to create your custom boundary. You can also set

an alarm to show you how close you are and to notify you that you have entered into

these boundaries. Tap on the boundary you have created and toggle the “Alarm”to “ON”.

Then add “Boundary Alarm Zone” to the Nav Data Bar.

DFF1-UHD DIP Switch Settings

Connection to NavNet 3D,TZtouch,TZtouch2 and TZtouch3

The DFF1-UHD Dip Switches on S2 are defaulted to work with NavNet TZtouch, TZtouch2 and

TZtouch3 MFDs. When connecting the DFF1-UHD to a TZtouch network you do not need to

change the default position of the Dip Switches on S2.

If the DFF1-UHD was installed in a NavNet 3D MFD (MFD8, MFD12 or MFDBB) network, the

DIP Switches on S2 must be changed to the position shown below.

DFF1/BBDS1 Mode Switch Settings

Connection to NavNet 3D,TZtouch,TZtouch2 and TZtouch3

DFF1/BBDS1 Mode Switches are defaulted to work with NavNet 3D MFD (MFD8, MFD12 or

MFDBB) network. When connecting the DFF1/BBDS1 to a TZtouch network you will need to

change the default position of the MODE Switches.

If the DFF1/BBDS1 was installed in a NavNet 3D MFD (MFD8, MFD12 or MFDBB) network, the

Mode Switches must be changed to the position shown below.

DFF3 DIP Switch Settings

Connection to NavNet 3D,TZtouch,TZtouch2 and TZtouch3

The DFF3 Dip Switch setting on S2 is defaulted to work with NavNet3D (MFD8, MFD12 or

MFDBB) network. When connecting the DFF3 to a TZtouch network you will need to change

the default position of the Dip Switches.

If the DFF3 was installed in a NavNet 3D MFD (MFD8, MFD12 or MFDBB) network, the Dip

Switches must be changed to the position shown below.

PSU012/PSU013

Jumper Location for TZtouch Series Installations

If PSU013 or PSU012 was used in a NN3D network with HUB101 the J7 Jumper would not

have been inserted. Jumper must be inserted in J7 to bypass Power Synch. TZtouch networks

do no use Power Synch (DHCP). If you are missing the Jumper you can order a replacement.

The part number for Jumper is 000-153-879.

Andere Handbücher für NavNet TZtouch3 Series

Dieses Handbuch passt für folgende Modelle

Andere Furuno Schiffsausrüstung Handbücher

Furuno

Furuno LS-6100 Bedienungsanleitung

Furuno

Furuno FCV-292 Bedienungsanleitung

Furuno

Furuno CN-24 Bedienungsanleitung

Furuno

Furuno F-851SD Bedienungsanleitung

Furuno

Furuno FICE-100 Bedienungsanleitung

Furuno

Furuno DSC-6 Handbuch

Furuno

Furuno FCV-582L Bedienungsanleitung

Furuno

Furuno NAVpilot-300 Installationsanleitung

Furuno

Furuno GS-100 Bedienungsanleitung

Furuno

Furuno FRS-1000 Handbuch

Furuno

Furuno NAVpilot 711C Bedienungsanleitung

Furuno

Furuno DFF1 Bedienungsanleitung

Furuno

Furuno LS-6000 Bedienungsanleitung

Furuno

Furuno FCV-561 Bedienungsanleitung

Furuno

Furuno FCV-600L Bedienungsanleitung

Furuno

Furuno FCV-295 Bedienungsanleitung

Furuno

Furuno GP-1650DF Bedienungsanleitung

Furuno

Furuno Black Box Video Sounder FCV-1200BB Bedienungsanleitung

Furuno

Furuno MU-270W Gebrauchsanweisung

Furuno

Furuno LC-90MK2 Beilage

Furuno

Furuno FA-30 Bedienungsanleitung

Furuno

Furuno Navigational Echo Sounder FE851S Bedienungsanleitung

Furuno

Furuno TECDIS Bedienungsanleitung

Furuno

Furuno FE-700 Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch

olympia electronics

olympia electronics ΒS-532/WP Bedienungsanleitung

olympia electronics

olympia electronics ΒS-531/1/MAR Bedienungsanleitung