Furuno NAVpilot-611 Bedienungsanleitung

www.furuno.co.jp

AUTOPILOT

NAVpilot-611

Installation Manual

TABLE OF CONTENTS

SAFETY INSTRUCTIONS.......................i

SYSTEM CONFIGURATION ..................ii

EQUIPMENT LISTS .............................. iii

1. INSTALLATION OF UNITS .......... 1-1

1.1 Control Unit FAP-6011..................... 1-1

1.2 Processor Unit FAP-5002................ 1-3

1.3 Rudder Reference Unit FAP-6112 ... 1-4

1.4 Remote Controllers (option) ............ 1-5

2. WIRING ....................................... 2-1

2.1 Wiring System ................................. 2-1

2.2 Processor Unit................................. 2-2

2.3 Control Unit ..................................... 2-7

2.4 Remote Controllers (option) ............ 2-8

2.5 Connection of Instruments FI-30 ... 2-11

2.6 Input/Output Sentences................. 2-12

3. ADJUSTMENTS........................... 3-1

3.1 How to Access the Installation Menu....

....................................................... 3-1

3.2 DOCKSIDE SETUP Menu .............. 3-2

3.3 SEA TRIAL Menu...........................3-11

3.4 DISPLAY SETUP Menu ................ 3-16

3.5 DATA CALIBRATION Menu........... 3-18

3.6 Other Settings............................... 3-20

PACKING LISTS.................................A-1

OUTLINE DRAWINGS ..................... D-1

INTERCONNECTION DIAGRAMS ...S-1



Thepaperusedinthismanual

iselementalchlorinefree.

・FURUNOAuthorizedDistributor/Dealer

9‑52Ashihara‑cho,

Nishinomiya,662‑8580,JAPAN

Telephone: +81‑(0)798‑65‑2111

Fax:

+81‑(0)798‑65‑4200

AUG

2008

PrintedinJapan

Allrightsreserved.

Pub.No.

IME‑72750‑A

00016935610

(

HIMA

)

NAVPILOT‑611

00016935610

*00016935610*

WARNING

Turn off the power at the switchboard

before beginning the installation.

Fire or electrical shock can result if the

power is left on.

Use the specified power cable.

Use of other power cable may result in

fire.

CAUTION

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

Control unit

Standard Steering

compass compass

0.30 m 0.30 m

Confirm that the power supply voltage

is compatible with the voltage rating

of the equipment.

Connection to the wrong power supply

can cause fire or equipment damage.

Processor

unit 0.35 m 0.30 m

SAFETY INSTRUCTIONS

Remote

controllers 0.30 m 0.30 m

Confirm that no one is near the rudder

when bleeding air from oil cylinder.

The rudder may move unexpectedly,

possibly causing bodily injury.

When connecting a geomagnetism

detection type heading sensor,

correct magnetic field deviation.

If an autopilot is used without the compen-

sation, unexpected course change may

occur.

Set REMOTE CONTROLLER 1 and 2 on

SYSTEM SETUP menu properly accord-

ing to remote controller connected.

If not done properly, malfunction may

occur. Especially, take care when

setting the NFU-type remote controller.

SYSTEM CONFIGURATION

Standard configuration is shown with solid line.

12-24 VDC

Processor Unit

FAP-5002

Control Unit

FAP-6011 (Max. 6)*

Heading sensor

PG-500

Rudder Reference Unit

FAP-6112

Remote Controller

Distributor FAP-6800

Remote Controller

Reversible pump or

Electromagnetic valve unit

External buzzer

Navigator

(NMEA0183)

RD-30 (Max. 3)

(NMEA0183)

Clutch

Remote Controller

Remote controler

Dial type: FAP-5551, FAP-5552

Button type: FAP6211, FAP-6212

Lever type: FAP-6221, 6222

Dodge type: FAP-6231, 6232

Ship's steering system

*: Any combination of FAP-5001, 5011 and 6011 is available.

Also, FAP-5021 can be connected at the end of series.

iii

EQUIPMENT LISTS

Standard supply for Navpilot-500

Name Type Code No. Qty Remarks

Control Unit FAP-6011 - 1

Processor Unit FAP-5002 - 1

Rudder Reference Unit FAP-6112-200 - 1 w/20 m cable

CP64-02700 001-050-070 1 set For Control Unit, MJ-A7SPF

cable and CP64-02701

CP64-02210 009-000-620 1 set For Processor Unit, MJ-A7SPF

cable and CP64-02211

Installation Materials

CP64-02601 009-001-170 1 set For Rudder reference Unit

Spare Parts SP64-01401 009-000-610 1 set For Processor Unit, fuse

Accessories FP64-01301 001-050-080 1 set For Control Unit

Optional supply

Name Type Code No. Qty Remarks

FAP-6011 -

FAP-5001-E -

Max. 5 optional units

Control Unit

FAP-5021-E -

Max. 1 optional unit

FAP-5551-E 000-090-224 1 set Dial type, w/connector

FAP-5552-E 000-090-269 1 set Dial type, w/o connector

FAP-6211-E 000-090-235 1 set Button type, w/connector

FAP-6212-E 000-090-271 1 set Button type, w/o connector

FAP-6221-E 000-090-239 1 set Lever type, w/connector

w/CP64-01100

FAP-6222-E 000-090-273 1 set Lever type, w/o connector

w/CP64-01100

FAP-6231-E 000-090-251 1 set Dodge type, w/connector

Remote

Controller

FAP-6232-E 000-090-279 1 set Dodge type, w/o connector

Junction box FAP-6821 000-090-411 1 For FAP-5021 extension

Distributor FAP-6800 000-090-242 1 set For 3 remote controllers connection

MJ-A7SPF0010-100C 000-159-681-10 1 w/ connector at one end, 10 m

MJ-A7SPF0010-150C 000-159-682-10 1 w/ connector at one end, 15 m

MJ-A7SPF0010-200C 000-159-683-10 1 w/ connector at one end, 20 m

MJ-A7SPF0012-100C 000-159-684-10 1 w/ connector at both ends, 10 m

Cable Assy

MJ-A10SPF0001-120 000-126-660 1

Between processor unit and

distributor

Rudder

Reference Unit FAP-6112-200 - 1 w/20 m cable

Terminator MJ-A7SPF0011 000-147-017 1

Flush mount kit FAP-6011-FLUSH-KIT 000-169-369-10 1 For FAP-6011, flush mounting

Hanger OP64-2 009-004-030 1 For FAP-5551/5552

OP64-4 009-005-790 1 For FAP-6221/6222, panel type

Flush mount kit

OP64-5 009-005-800 1 For FAP-6221/6222, surface type

This page is intentionally left blank.

1-1

1. INSTALLATION OF UNITS

1.1 Control Unit FAP-6011

The display unit can be installed two ways: surface mount and flush mount (optional kit

required). This section covers surface mounting. For flush mounting, see the flush mounting

instructions, issued separately. Use the supplied display hard cover when the system is not

in use.

Control unit FAP-6011

When selecting a mounting location for the control unit, keep the following in mind.

• The mounting location should be well ventilated.

• Mount the unit where shock and vibration are minimal.

• Do not mount the display unit under “Plexiglas” or any other type of shielding which could

trap heat and moisture or magnify sunlight energy onto the surface of the display.

• For maintenance and checking purposes, leave sufficient space at the sides and rear of

the unit and leave slack in cables.

• A magnetic compass will be affected if the control unit is placed too close to the magnetic

compass. Observe the compass safe distances to prevent disturbance to the magnetic

compass shown on page i.

1. INSTALLATION OF UNITS

1-2

Mounting

1. Using the template supplied with the unit open a mounting hole in the installation site.

2. Detach the front panel together with the keypad. Attach sponge (supplied) to rear of the

control unit.

3. Set the control unit to the mounting hole, and fix it with four self-tapping screws (3x20,

supplied).

4. Attach the keypad and the front panel to the display unit.

Flush mounting of control unit

How to detach the front panel from the mounting place

To detach the front panel after mounting the unit, use the remover (supplied) as below. Note

that the front panel may be damaged if the following is not done. This method is also

available for the optional surface mounting kit.

1. Set the remover to a notch on the upper side of the unit, and pull the remover to raise

the panel slightly.

2. Similarly use the remover to raise the panel at the lower side.

Remover

3. Use your hands to detach the front panel.

Front panel

Keypad

Display unit

Self-tapping screw

(3x20)

Sponge

1. INSTALLATION OF UNITS

1-3

1.2 Processor Unit FAP-5002

This unit can be mounted on a desktop or on a bulkhead. Select a mounting location

considering the points below.

• Locate the unit out of direct sunlight and water splash.

• Select a location where temperature and humidity are moderate and stable.

• Consider the length of the cable connected between the processor unit and other units.

• Locate the unit where its cover can be removed and cabling easily accessed.

• For mounting on a bulkhead, be sure the mounting location is strong enough to support

the unit under the pitching and rolling normally encountered on the vessel.

• Leave sufficient space around the unit for maintenance and servicing. Recommended

maintenance space appears in the outline drawing at the back of this manual.

• A magnetic compass will be affected if the processor unit is placed too close to the

magnetic compass. Observe the compass safe distances to prevent disturbance to the

magnetic compass: standard: 0.35 m, steering: 0.3 m.

1. Unfasten five pan head screws to remove the cover.

2. Mount the unit as follows:

Tabletop: Fasten with four self-tapping screws.

Bulkhead mounting: Screw lower two self-tapping screws into the mounting location, leaving

5 mm protruding. Secondary screw upper two screws. Set the processor unit to the screws

and tighten screws.

3. Reattach the cover.

Processor unit

1. INSTALLATION OF UNITS

1-4

1.3 Rudder Reference Unit FAP-6112

• Leave sufficient space around all moving parts.

• The unit must be coupled to the rudder as shown below, where the following conditions

are satisfied:

Use four self-tapping screws (supplied) to fasten the rudder reference unit.

350 mm <Y2 < 540 mm

X1 = X2

Y1 = Y2

X1 X2

Top view

Arrow mark

Note: The arm of rudder reference unit should be aligned with the arrow mark. Align the

notch on the shaft to the arrow mark if the arm is removed.

Inhaltsverzeichnis

Andere Furuno Schiffsausrüstung Handbücher

Furuno

Furuno DS-85 Bedienungsanleitung

Furuno

Furuno TZT2BB Bedienungsanleitung

Furuno

Furuno FI70BW Bedienungsanleitung

Furuno

Furuno FCV-292 Bedienungsanleitung

Furuno

Furuno FI70DSW Bedienungsanleitung

Furuno

Furuno FMD-3200 Bedienungsanleitung

Furuno

Furuno FRS-1000 Handbuch

Furuno

Furuno GP-1850WF Bedienungsanleitung

Furuno

Furuno GP-1850WDF Bedienungsanleitung

Furuno

Furuno RD-33 Bedienungsanleitung

Furuno

Furuno FE-808 Bedienungsanleitung

Furuno

Furuno GP-3500F Bedienungsanleitung

Furuno

Furuno MFD8 Handbuch

Furuno

Furuno LS-6000 Bedienungsanleitung

Furuno

Furuno NAVpilot 711C Bedienungsanleitung

Furuno

Furuno DSC-6A Bedienungsanleitung

Furuno

Furuno FCV-1150 Bedienungsanleitung

Furuno

Furuno NavNet TZtouch3 Series Bedienungsanleitung

Furuno

Furuno FI5002 Betriebsanleitung

Furuno

Furuno FMD3100 Handbuch

Furuno

Furuno NavPilot 711 Bedienungsanleitung

Furuno

Furuno FE-700 Bedienungsanleitung

Furuno

Furuno FCV-30 Bedienungsanleitung

Furuno

Furuno GP-1810F Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Notifier

Notifier FS-BSO Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch

olympia electronics

olympia electronics ΒS-532/WP Bedienungsanleitung

olympia electronics

olympia electronics ΒS-531/1/MAR Bedienungsanleitung