Furuno MCU-002 Bedienungsanleitung

Model: MCU002

Remote Control Unit

Index

1. Model: MCU002

2. Specications

2-1. Standard Comprising

2-2. Technical Specications

3. Operations – User Interface

3-1. Getting Started – Model TZT9/14/BB New Version v3.12

3-2. Keys and Functions – Basic Operations

3-3. Showing a Cross Cursor – New with Model TZT9/14/BB v3.12

3-4. Auto Scroll ON or OFF – New with Model TZT9/14/BB v3.12

3-5. Entering a Point – New with Model TZTBB and TZT14 (External Touch

Screen Mode) v3.12

3-6. User Interface Auto-Hide “10 Seconds” Recommended

3-7. Limitations and Notes

4. Installing Model MCU002

4-1. Dimensions

4-2. Flush Mounting

4-3. Interconnection

5. Model MCU002 with TZT9/14/BB v3.02 or Earlier

6. Tips – Model TZT9/14/BB with Generic HID Mouse

1. Model: MCU002

The Model MCU002 is a compact remote control unit

for use with the TZT9/14/BB. It offers the

expandability of multi touch operation of the

TZT9/14/BB to the hardware key operation, as the

best supplemental tool to multi touch operation. This

document describes the basic information on

specifications, operations, and installation of the

MCU002. Model: MCU002

Screen Image from TZTBB

2. Specifications

2-1. Standard Comprising

The MCU002 (00002546100) comes with the components shown at right.

(Components) (Carton)

2-2. Technical Specifications

Interface USB2.0

Cable Length 2 m

Power Supply via USB port

Water Proof Front: IP56

Rear: IP22

Operating Temperature -15 to +55℃

Humidity 40℃94% or less (without internal fogging)

Mounting Flush mount from the front side (See Section 4-2)

Name Type Qty

L (175 mm)

W (85 mm)

H (100 mm)

Remote control unit MCU002 1

Front panel FRC-D01-003 1

Flush mount gasket FRC-D01-008 1

Flush mount screw BH3*13 TAB-B 4

User’s Guide (English) 1

3. Operations – User Interface

3-1. Getting Started – Model TZT9/14/BB New Version v3.12

To fully make use of the MCU002, update the TZT9/14/BB to v3.12, which will be released in May 2014.

3-2. Keys and Functions – Basic Operations

The MCU002 consists of 10 hardware keys to control the TZT9/14/BB as described below.

MCU002 No Keys Descriptions

(1) STBY / AUTO Sets the NAVpilot-700 to STBY or AUTO modes

(2) CENTER Sets the ship in the center of the screen

(3) CURS / SCRL Switches the joystick functions between Cursor and Scroll

(4) Joystick Moves a cursor in 8 directions

(5) －/ ▲(UP) Acts as rotating RotoKey™ clockwise

(6) ＋/ ▼(DOWN)

Acts as rotating RotoKey™ counterclockwise

(7) ENT Acts as pushing RotoKey™

(8) CANCEL & MOB Short presss to cancel

Long press to enter an MOB point

(9) FUNC Acts as Function Gesture

(10) HOME & BRILL Short press to access the Home page

Long press to open the Brilliance control box

(1) STBY / AUTO

This key activates the NAVpilot-700 AUTO and STBY modes. When opening the NAVpilot-700

control window on the TZT9/14/BB, you can activate the AUTO mode from the MCU002 [STBY/AUTO]

key.

When the NAVpilot-700 mode is changed between AUTO/NAV and STBY with the MCU002 or touch operations, the

TZT9/14/BB will generate a beep sound with the following notification on the top of the screen.

STBY to AUTO/NAV AUTO/NAV to STBY

The notification of [NAVpilot is engaged.] will appear. The notification of [NAVpilot is disengaged.] will appear.

(2) CENTER

This key sets the own vessel to the center on the screen of Plotter and Radar and cancels echo history of Fish Finder.

(3) CURS / SCRL (CURSOR / SCROLL)

This key switches the joystick functions between cursor and scroll modes. At default the

joystick works to move a cursor. Pressing the [CURS/SCRL] key, the joystick works to scroll the Chart,

Radar, and Fish Finder screen.

Plotter screen – Cursor in motion Plotter screen – Scrolled with joystick

(4) Joystick

The joystick can move in eight (8) directions to move a cursor or scroll the screen as shown

above. It also has a “push” function. As an example, if you push the joystick on the Plotter screen,

contextual menus will appear as follows.

(Sample: Plotter screen from TZTBB)

Note:

The joystick has NO “drag” function. For details on limitations

of operations with the MCU002, see Section 3-5.

(5) －/ UP (▲)

(6) ＋/ DOWN (▼)

(7) ENT

These three (3) components work as the RotoKey™: [-/▲(UP)] key as rotating the RotoKey™

clockwise, [+/▼(DOWN)] key as rotating the RotoKey™ counterclockwise, and [ENT] as pushing the

RotoKey™. The following screenshots from the Plotter page show how to operate these keys.

Press [ENT] to show RotoKey™ menus. Press [-/▲] or [+/▼] to move the RotoKey™ menus and

press [ENT]. In this example, [Overlay] is selected.

Press [-/▲] or [+/▼] to zoom in or zoom out the Plotter and Radar screen.

(8) CANCEL & MOB

This key has two (2) functions: Short press to activate the “CANCEL” and long press the “MOB”

functions as shown below.

Short Press for “CANCEL” Long Press for “MOB”

- Closes Home/Menu/Lists/Tides/Catalog pages,

RotoKey™ and contexual menus, and dialog boxes

- Mutes alarm sound

- Ends action such as creating a route and moving a point

Note: No “Undo” function

- Enters an MOB point at the own ship’s position

(9) FUNC (FUNCTION)

This key activates the function set in [Menu] – [General] – [Function Gesture]. In the following

example, the Function Gesture is assigned to [Event]. The [FUNC] key pops up the event window. You

can select an event mark with the [-/▲] or

[+/▼] key and enter it with the [ENT] key,

or place a cursor with the joystick on a

required event mark and push the joystick.

(10) HOME & BRILL

This key has two (2) functions: Short press to activate the “HOME” and long press the “BRILL”

functions. On the Home page and Brilliance window, you can proceed to further settings as follows.

Short Press for “HOME” Long Press for “BRILL”

Press [-/▲] or [+/▼] to select a page and [ENT] to open

the selected page.

Press [-/ ▲] or [+/ ▼] to adjust the brillaince and

[CANCEL] to close the window. To turn off the unit, place

a cursor with the joystick on [Power Off This Device] or

[Power Off Network] and press it.

Note:

It is not possible to turn on the TZT9/14/BB with the MCU002 although the power can be turned off as shown above.

3-3. Showing a Cross Cursor – New with Model TZT9/14/BB v3.12

The TZT9/14/BB v3.12 program has new setting options of Cross Cursor and Cross Cursor Speed, which enables to

show a cross cursor on the screen and adjust its speed. With the MCU002, the cross cursor will help to see a present

cursor location.

Menu Settings Cross Cursor on Screen

[Menu] – [General] – [Cross Cursor] – [ON] While the joystick in operation, the gray, thick cross cursor

appears on the screen.

[Menu] – [General] – [Cross Cursor Speed] – [1] to [20]

The cursor speed can be adjusted between [1] and [20]:

[1] – slowest, [8] – default, and [20] – fastest.

Cross Cursors on Other Screens

Tips – No cross cursor while touch operations

When the TZT9/14/BB is operated by touch, the cross cursor will not appear. The cross cursor will appear only when

the cursor is in operation with the MCU002 joystick.

3-4. Auto Scroll ON or OFF – New with Model TZT9/14/BB v3.12

The TZT9/14/BB v3.12 program has another new setting option of Auto Scroll, which enables to scroll the Plotter, Radar,

and Sounder screen by placing a cursor at the edge of the screen. The following screenshots show the menu settings and

scroll motions.

Menu Settings

[Menu] – [General] – [Auto Scroll] – [ON]

Menu Settings

[Menu] – [General] – [Auto Scroll] – [OFF] (Default)

In this example, a cursor is placed at the left edge of the

Plotter screen, while the chart is automatically scrolled.

(You can see the [Center Vessel] icon.) To stop the scroll

motion, place the cursor away from the edge.

At default, the Auto Scroll mode is set to OFF. When a cursor

is placed at the edge of the screen, the chart is not scrolled.

3-5. Entering a Point

– New with Model TZTBB and TZT14 (External Touch Screen Mode) v3.12

Pushing the MCU002 joystick, [New Point] will be highlighted at default on the contextual menus. You can just press

[ENT] to enter the point.

Note:

This specification is for the TZTBB and TZT14 under the External Touch Screen Mode only. With the TZT9 and TZT14

Andere Handbücher für MCU-002

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Furuno Fernbedienung Handbücher

Furuno

Furuno MCU-002 Bedienungsanleitung

Furuno

Furuno MCU-002 Bedienungsanleitung

Furuno

Furuno GD-8540 Handbuch

Furuno

Furuno MCU-002 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung