Furuno CSH-7 Bedienungsanleitung

COLOR SCANNING SONAR

MODEL CSH-7

FIRST EDITION : MAY 1997

 D : NOV. 5,1998

Your Local Agent/Dealer

FURUNO ELECTRIC CO

LT D

9-52, Ashihara-cho,

Nishinomiya, Japan 662

Telephone: 0798-65-2111

Telefax: 0798-65-4200

Printed in Japan

PUB. No. IME-13020-D

CSH-7

(TATA)

iiiiiiiiiiiii

SAFETYINSTRUCTIONS

Do not work inside the

equipment unless totally

familiar with electrical

circuits.

Hazardous voltage which can

shock exists inside the equip-

ment.

Turn off the power at the

mains switchboard before

beginning the installation.

Post a sign near the switch

to indicate it should not be

turned on while the equip-

ment is being installed.

Fire or electrical shock can

result if the power is left on or

is applied while the equip-

ment is being installed.

WARNING

Install the display unit and transceiver

unit where they will not be exposed to

water splash or rain.

Fire or electrical shock can result if water

leaks inside those units.

Ensure no water leaks through the

mounting location for the transducer.

The ship may sink if water leaks through the

mounting location. Check the location care-

fully at installation.

The retraction tank should be con-

structed of the specified material and

installed in accordance with the pro-

cedures set forth in this manual. Use of

other material or procedure is the

responsibility of the shipyard. In any

case the tank should be installed so

the hull will not be seriously damaged

in the event the tank is struck by an

object.

CAUTION

Use the proper fuse.

Use of a wrong fuse can result in fire or

permanent equipment damage.

Replace zinc block near the transducer

yearly.

If not replaced corrosion between trans-

ducer and main shaft may result.

Do not exceed speed noted in the speci-

fications when operating the equipment

or lowering or raising the transducer.

The transducer may become damaged.

Ground the equipment to

prevent mutual interference.

POSSIBILITY OF INJURY

1. If breaker (hull unit) trips do the

following:

1) Turn off power swich on hull unit.

2) Wait 60 sec after breaker has tripped.

3) Press breaker.

2. Turn off hull unit before using hand

crank.

WARNING

POSSIBILITY OF WATER LEAKAGE

To prevent loss of main shaft of the hull

unit and water leakage tighten bolts fixing

shaft retainer for torque of 2000-2500 N•

cm and tighten fastening band for torque

600-800 N•cm.

iii

TABLEOFCONTENTS

SYSTEM CONFIGURATION .................................................................................. iii

MOUNTING

1.1 General Mounting and Handling Considerations ............................................................1-1

1.2 Mounting the Hull Unit ...................................................................................................1-2

1.3 Mounting the Transceiver Unit......................................................................................1-11

1.4 Mounting the Display Unit ............................................................................................1-11

1.5 Grounding the Display Unit and Transceiver Unit ........................................................1-12

WIRING

2.1 Wiring Diagram ...............................................................................................................2-1

2.2 Wiring the Hull Unit ........................................................................................................2-2

2.3 Wiring the Transceiver Unit.............................................................................................2-3

2.4 Wiring the Display Unit...................................................................................................2-4

2.5 Synchronizing Transmission with Other Equipment .......................................................2-5

2.6 How to Unplug the XH Connector ..................................................................................2-7

CHECKS ANDADJUSTMENTS

3.1 General Checks................................................................................................................3-1

3.2 Heading Alignment ..........................................................................................................3-3

3.3 Sea Trial ...........................................................................................................................3-4

INSTALLATION OF INTERFACE MODULE CSH-7050 (option)

4.1 Introduction .....................................................................................................................4-1

4.2 Installation .......................................................................................................................4-2

ASSEMBLING TRANSCEIVER FRAME (Option).................................... 5-1

DRAWINGS

Equipment Lists ....................................................................................................................A-1

Outline Drawings..................................................................................................................D-1

Interconnection Diagram ...................................................................................................... S-1

Schematic Diagram............................................................................................................... S-2

SYSTEMCONFIGURATION

Equipment Lists

Standard Supply

emaNepyTytQssaM )gk( skrameR

1tinUyalpsiD0107-HSC101

2reviecsnarT tinU 0207-HSC15.11

3tinUlluH0307-HSC 146ekortsmm006

1307-HSC06ekortsmm004

4noitallatsnI slairetaM 00040-01PC tes1 elbacm5sulp10040-01PCtceleS eno

01040-01PCelbacm01sulp10040-01PC

02040-01PCelbacm51sulp10040-01PC

03040-01PCelbacm03sulp10040-01PC

5seirosseccA01340-30PFtes1

6straPerapS00320-01PStes1

7etomeR rellortnoC 0407-HSCtes100240-01PCslairetam.tsnihtiW

Optional Equipment

emaNepyTytQ.oNedoCskrameR

1eludoMecafretnI0507-HSCtes1— tinuyalpsidnitliuB

2emarFreviecsnarT tiK 41-01PO1046-039-600.ceDmorfelbaliavA 7991

3reifitceR4243-UR1—

4knaTnoitcarteR5-01POtes1367-960-000dnaknatmunimulA teksagnoitalusni

5revoCtsuD1042-340-411030-561-001

6dooH02130-30PF1011-932-800tinuyalpsidrof

1-1

MOUNTING

1.1 General Mounting and Handling Considerations

• Be sure the power supply matches equipment voltage rating. Improper power supply will

damage the equipment.

• Locate the transducer where the affects of noise and air bubbles are minimal. Noise and air

bubbles will affect performance.

• When selecting a mounting location keep the following points in mind:

• Keep equipment out of direct sunlight.

• Keep equipment away from air conditioner.

• The useable temperature range of the display unit is 0°–50°C.

• Provide sufficient ventilation.

• Select location where vibration is minimal.

• Locate the equipment away from magnets and magnetic materials.

• Keep the transducer away from oil. Oil can corrode the cable.

• Do not expose the transducer to hot water. Hot water can damage the transducer.

• Do not turn on the equipment with the transducer exposed to air. Exposing the transducer to

air may damage it.

• Magnetic compass performance will be affected if it is placed too close the display unit.

Observe the compass safe distances shown below to prevent deviation of a magnetic com-

pass.

Standard compass: 1.3 m

Steering compass: 1.0 m

1-2

1.2 Mounting the Hull Unit

Location

Discussion and agreement are required with the dockyard and ship owner in deciding the loca-

tion for the hull unit. When deciding the location, take into account the following points:

• Select an area where propeller noise, cruising noise, bubbles and interference from turbu-

lence are minimal. Generally, the point at 1/3 to 1/2 of the ship’s length from the bow or near

the keel is the best. On-the-keel installation is advantageous for minimizing oil consumption

in comparison with off-the-keel. If the hull unit cannot be installed on the keel, the center of

the retraction tank should be within 1 meter of the keep to prevent a rolling effect.

1/2 1/3 Within 1 m

Figure 1-1 Installation location for hull unit

• Select a place where interference from the transducers of other sounding equipment is mini-

mal.The hull unit should be at least 2.5 meters away from the transducers of other sounding

equipment.

• An obstacle in the fore direction not only causes a shadow zone but also aerated water,

resulting in poor sonar performance. Be sure to locate the transducer well away from any

obstacle in the fore direction.

• The following space is required around the hull unit for wiring and maintenance. If the

transducer is to be operated in ambient temperature below 0°C, the sonar compartment must

be provided with a heater to keep the temperature above 0°C.

BOW

Direction

400800

400 800

45°

If the space shown is not available,

leave at least 50 cm in fore

direction.

Figure 1-2 Hull unit maintenance space

1-3

Installation of the retraction tank

The retraction tank is 1000 mm in length as supplied. Shorten the tank referring to the table

below so the transducer fully protrudes beyond the keel when it is lowered. Refer to pages D-1

to D-6 for details.

Figure 1-3 How to shorten the retraction tank

Reletion of tank length and shft length

Shaft supplied 945 1300 1550 2350

Shaft/Cut length Shaft

length Cut

length Shaft

length Cut

length Shaft

length Cut

length Shaft

length Cut

length

Hull Unit Tank

length

400

Stroke 550 945 0

600

Stroke

750 1300 0

800 1365 185

850 1415 135

900 1465 85

950 1515 35

1000 1550 0

1100 1665 685

1200 1765 585

1300 1865 485

1400 1965 385

1500 2065 285

1600 2165 185

1700 2265 85

1800 2350 0

Andere Handbücher für CSH-7

Inhaltsverzeichnis

Andere Furuno Sonar Handbücher

Furuno

Furuno Black Box Searchlight Sonar CH-250BB Bedienungsanleitung

Furuno

Furuno CSH-53 Bedienungsanleitung

Furuno

Furuno CH-24 Bedienungsanleitung

Furuno

Furuno CSH-83 Bedienungsanleitung

Furuno

Furuno CSH-5L Bedienungsanleitung

Furuno

Furuno CH-37BB Bedienungsanleitung

Furuno

Furuno FSV-85-MARK-2 Bedienungsanleitung

Furuno

Furuno CH-270 Bedienungsanleitung

Furuno

Furuno CSH-23/24 Bedienungsanleitung

Furuno

Furuno CHS-5LMARK-2-55 Bedienungsanleitung

Furuno

Furuno FSV-85 Bedienungsanleitung

Furuno

Furuno CI-88 Bedienungsanleitung

Furuno

Furuno CH-250 Bedienungsanleitung

Furuno

Furuno CSH5LMK2 Bedienungsanleitung

Furuno

Furuno CH-28 Bedienungsanleitung

Furuno

Furuno CH-270 Betriebsanleitung

Furuno

Furuno COLOR SCANNING CSH-55 Bedienungsanleitung

Furuno

Furuno FSV25 Bedienungsanleitung

Furuno

Furuno CH-300 Bedienungsanleitung

Furuno

Furuno FSV-75 Bedienungsanleitung

Furuno

Furuno FSV-24 Bedienungsanleitung

Furuno

Furuno FSV-75 Bedienungsanleitung

Furuno

Furuno FCV-360 Bedienungsanleitung

Furuno

Furuno CH-16 Bedienungsanleitung

Beliebte Sonar Handbücher anderer Marken

Kongsberg

Kongsberg Simrad SP90 Series Bedienungsanleitung

Eagle

Eagle TriFinder 2 Bedienungsanleitung

Lowrance

Lowrance X-70A Bedienungsanleitung

Lowrance

Lowrance LMS-150 GPS Bedienungsanleitung

Simrad

Simrad EQ 55 Bedienungsanleitung

Lowrance

Lowrance Traditional Bedienungsanleitung

Teledyne

Teledyne BlueView BV3200 Bedienungsanleitung

Reson

Reson SeaBat 7125 SV2 Bedienungsanleitung

Eagle

Eagle 101 Bedienungsanleitung

IMAGENEX

IMAGENEX 881A-GS Bedienungsanleitung

Eagle

Eagle Z-15 Bedienungsanleitung

Simrad

Simrad SH80 - REV C Bedienungsanleitung

Simrad

Simrad ST90 Bedienungsanleitung

Hawk

Hawk Sultan Bedienungsanleitung

Lowrance

Lowrance 1240A Bedienungsanleitung

Kongsberg

Kongsberg Flexview Bedienungsanleitung

VEXILAR

VEXILAR 107 PRO Bedienungsanleitung

Klein

Klein 5000 V2 Series Bedienungsanleitung