Furuno FSV-84 Bedienungsanleitung

COLOR SCANNING SONAR

FSV-84

www.furuno.co.jp

The paper used in this manual

is elemental chlorine free.

・FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,

Nishinomiya, 662-8580, JAPAN

Telephone : +81-(0)798-65-2111

Fax

+81-(0)798-65-4200

A : SEP 2006

Printed in Japan

B3 : JUN . 21, 2007

Pub. No. IME-13290-B3

*00015742911**00015742911*

(DAMI ) FSV-84

00015742911

* 0 0 0 1 5 7 4 2 9 1 1 *

WARNING

Do not install the equipment where it

may get wet from rain or water splash.

Water can cause fire or electrical shock, or

damage the equipment.

Be sure no water leaks in at the trans-

ducer installation site.

Water leakage can sink the vessel. Also

confirm that the transducer will not loosen

by ship's vibration. The installer of the

equipment is solely responsible for the

proper installation of the equipment.

FURUNO will assume no responsibility for

any damage associated with improper

installation.

Install the specified transducer tank

in accordance with the installation

instructions. If a different tank is to be

installed the shipyard is solely respon-

sible for its installation, and it should

be installed so the hull will not be

damaged if the tank strikes an object.

The tank or hull may be damaged if the

tank strikes an object.

DANGER

Keep away from raise/lower

shaft in hull unit when it is

moving.

Gears will cause serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury.

Warning, Caution Mandatory Action

Prohibitive Action

SAFETY INSTRUCTIONS

The installer must read the safety instructions before attempting to install the equipment.

DANGER

Indicates a potentially hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING

Do not open the equipment unless

totally familiar with electrical circuits

and service manual.

High voltage exists inside the equipment,

and a residual charge remains in capacitors

severalminutes after the power is turned off.

Improperhandling can result in electrical

shock.

Turn off power at the switchboard before

beginning the installation.

Electrical shock or fire can result if the

the power is left on.

CAUTION

Maximum speed while the transducer is

projected or being raised or lowered

is as below, to prevent damage to the

transducer.

Projected Raising/

Lowering

800 mm stroke Max. 18 kt Max. 15 kt

1100 mm stroke Max. 18 kt Max. 15 kt

Observe the following compass safe

distances to prevent interference to a

magnetic compass:

Processor Unit

Control Unit

Monitor Unit

Standard

compass Steering

compass

2.05 m 1.35 m

0.20 m 0.15 m

1.25 m 0.85 m

Ground the equipment to prevent

electrical shock and mutual

interference.

WARNING

If a steel tank is installed on a wooden

or FRP vessel, take appropriate

measures to prevent electrolytic

corrosion.

Electrolytic corrosion can damage the

hull.

Be sure to power each unit with proper

voltage.

Connection of an improper power supply

can cause fire or damage the equipment.

iii

TABLE OF CONTENTS

SYSTEM CONFIGURATION..........................................................................................iv

EQUIPMENT LISTS.......................................................................................................vi

1. MOUNTING THE EQUIPMENT..............................................................................1-1

1.1 Hull Unit ...............................................................................................................................1-1

1.2 Processor Unit .....................................................................................................................1-7

1.3 Monitor Unit (option)............................................................................................................ 1-8

1.4 Control Unit.........................................................................................................................1-11

1.5 Transceiver Unit.................................................................................................................1-13

1.6 Attachment Kit (option)...................................................................................................... 1-14

1.7 FRP Tank (option).............................................................................................................. 1-16

1.8 Control Box Extension Kit (option).....................................................................................1-18

2. WIRING ..................................................................................................................2-1

2.1 How to Use the Crimping Tool, Pin Extractor...................................................................... 2-1

2.2 Wiring...................................................................................................................................2-2

2.3 Monitor Unit (option)............................................................................................................ 2-4

2.4 Processor Unit .....................................................................................................................2-8

2.5 Transceiver Unit.................................................................................................................2-14

2.6 Control Box of Hull Unit.....................................................................................................2-17

2.7 Input Voltage and Fuses.................................................................................................... 2-18

2.8 Controller Extension Kit (Junction Box).............................................................................2-19

3. ADJUSTMENT AND CHECK.................................................................................3-1

3.1 Hull Unit Check.................................................................................................................... 3-1

3.2 Heading Adjustment.............................................................................................................3-4

3.3 Configuring Own Ship Mark................................................................................................. 3-6

3.4 Other SYSTEM Menu Items................................................................................................ 3-7

3.5 CONE Board Setting in the Processor Unit....................................................................... 3-12

3.6 DIP Switch Setting.............................................................................................................3-13

4. CONNECTING EXTERNAL INTERFACE CS-120A ..............................................4-1

PACKING LIST............................................................................................................A-1

OUTLINE DRAWINGS ................................................................................................D-1

INTERCONNECTION DIAGRAMS ............................................................................. S-1

SYSTEM CONFIGURATION

System with locally supplied monitor

Note 1: Power Kit (option, installed in

processor unit) required to connect CS-120A.

220 VAC,

3φ, 50/60 Hz

Loudspeaker

Echo Sounder,

Current Indicator,

other

Navigator 1

Navigator 2

AD Converter

AD-100

Current

Indicator

E/S Interface

VI-1100A

Net Recorder

VI-1100A

Net Sonde

Junction Box

CS-170

VI-1100A

Net Sonde

External

Interface CS-120A

(Note 1)

100-115/

220-230 VAC,

1φ, 50/60 Hz

External

Monitor

PROCESOR UNIT

FSV-8402

CONTROL UNIT

FSV-8401

External equipment

Option

100/110/115/

220/230 VAC,

1φ, 50/60 Hz

HULL UNIT

FSV-8432

FSV-8442

Speed Log

CONTROL UNIT

FSV-8401

TRANSCEIVER UNIT

FSV-841A

Satellite

Compass

SC-50/110

System with FURUNO monitor

PROCESSOR UNIT

FSV-8402

Current

Indicator

E/S Interface

VI-1100A

Net Sonde

Junction Box

CS-170

E/S Interface

VI-1100A

External

Interface CS-120A

(Note 1)

Net Recorder

VI-1100A

100-115/

220-230 VAC,

1φ, 50/60 Hz

220 VAC,

3φ, 50/60 Hz

HULL UNIT

FSV-8432

FSV-8442

Note 1: Power Kit (option, installed in

processor unit) required to connect CS-120A.

TRANSCEIVER UNIT

FSV-841A

100/110/115/

220/230 VAC,

1φ, 50/60 Hz

Loudspeaker

Sub Monitor

Echo Sounder,

Current Indicator,

other

Navigator 1

Navigator 2

AD Converter

AD-100

Speed Log

CONTROL UNIT

FSV-8401

MONITOR

UNIT

FSV-2400

Speed Log

CONTROL UNIT

FSV-8401

Net Sonde

External equipment

Option

Satellite

Compass

SC-50/110

EQUIPMENT LISTS

Standard supply

Name Type Code No. Qty Remarks

Control Unit FS

-8401-10

—

1 w/10 m cable

FSV-8402-100 — 110 VAC

Processor Unit FSV-8402-200 — 1 220 VAC

Transceiver Unit FS

-841

—

FSV-8432 — 800 mm stroke w/motion sensor

& no dome

Hull Unit FSV-8442 —

1 1100 mm stroke w/motion

sensor & no dome

CP10-06000 000-067-071 1 set

Cable between transceiver unit

and hull unit, 8 m

CP10-07011 001-005-660 1 set For transceiver unit

Installation

Materials* CP10-06100 000-067-067 1 set

For processor unit,

CP10-04502, CP10-04506

FP10-02901 007-008-780 1 set For

rocessor unit

Accessories* FP10-02201 006-922-390 1 set Memor

card for control unit

SP10-03101 007-008-530 1 set For transceiver unit

SP10-02601 006-921-340 1 set For

rocessor unit

Spare Parts* SP10-02603 006-921-360 1 set For hull unit

Optional equipment

Name Type Code No. Qty Remarks

Power Kit for

CS-120

FSV-2403 000-067-013 1

For CS-120A

Hood FP03-06503 008-490-970 1 For monitor unit

Loudspeaker SEM-21Q 000-144-917 1

MJ-

6SPF0012-050C 000-154-053-10 1 5 m, NMEA, 6P-6P

Cable Assy. MJ-

6SPF0012-100C 000-154-037-10 1 10 m, NMEA, 6P-6P

8-core Cable VVS 0.3×8C *6M* 000-555-043 1 6 m, for echosounder,

02S8040

37-core Cable 10S1258 000-101-006 1 Len

th specified b

user

E/S Interface VI-1100

—

Net Sonde

Junction Box CS-170 — 1

Monitor Unit FSV-2400-10 —

1 CP10-04501, FP03-06201,

FP10-02201, FP10-02202,

FP10-02203, Dust cover

-8401-5

—

w/5 m cable

Control Unit FSV8401-10

—

1 w/10 m cable

Installation

Material for

interface* CP10-04801 006-934-240 1

ttachment Kit OP10-30 00-067-179 See section 1.7.

OP10-28 000-067-077 1 For steel vessel

Retraction Tank OP10-29 000-067-178 For FRP vessel

Controller

Extension Kit FSV-846 — 1

For control box in hull unit

* See packing list at back of this manual.

1-1

1. MOUNTING THE EQUIPMENT

1.1 Hull Unit

Note 1: The raise/lower control box on the hull unit contains a motion sensor. Therefore,

never drop the hull unit.

Note 2: Handle the transducer carefully. Shock will damage its sensitive components.

1.1.1 Mounting considerations

Decide the location of the hull unit through consultation with the dockyard and ship owner.

When deciding the location, the following points should be taken into account.

• Choose an area where propeller noise, cruising noise, air bubbles and interference from

turbulence are at a minimum. Generally, the point at 1/3 to 1/2 of the ship’s length from the

bow on or near the keel is optimum. On-the-keel installation is advantageous for

minimizing oil consumption in comparison with off-the-keel. If the hull unit can not be

installed on the keel, the center of the retraction tank should be within 600 mm of the keel

to prevent a rolling effect. For large ship with deep draft, the hull unit can be installed at

the bow.

1/2 1/3 Within 600 mm

Hull unit mounting location

• Choose a place where the hull bottom is flat and the draft is sufficiently deep. Normally,

the transducer should protrude at least 500 mm beyond the keel to minimize the effect of

air foam and bubbles.

• Choose a place where interference from other transducers is minimal. The hull unit should

be at least 2.5 m away from the transducers of other equipment.

• No obstacle should be in the fore direction since it causes a shadow zone and aerated

water, resulting in poor sonar performance.

• The physical distance between the hull unit and the transceiver unit should be no more

than 5 m.

• The space shown in the figure on the next page is required around the hull unit for wiring

and maintenance.

• If the ambient temperature around the unit will be below0°C, provide the sonar

compartment with a heater to keep the temperature above 0°C. See the next page for

details.

1-2

Compartment

1200 mm 500 mm

500 mm

Maintenance space, example sonar compartment

Note: After mounting the equipment, be sure to install anti-vibration stays, as shown on

page 1-6.

Andere Handbücher für FSV-84

Inhaltsverzeichnis

Andere Furuno Sonar Handbücher

Furuno

Furuno CSH-5 MARK-2 Handbuch

Furuno

Furuno CH-500 Bedienungsanleitung

Furuno

Furuno DS-30 Bedienungsanleitung

Furuno

Furuno CSH-5L Bedienungsanleitung

Furuno

Furuno FSV-35 Bedienungsanleitung

Furuno

Furuno CSH-5 MARK-2 Bedienungsanleitung

Furuno

Furuno CH-300 Bedienungsanleitung

Furuno

Furuno CH-32 Bedienungsanleitung

Furuno

Furuno DS-60 Bedienungsanleitung

Furuno

Furuno COLOR SCANNING CSH-23F/24F Bedienungsanleitung

Furuno

Furuno MODEL CSH-73 Bedienungsanleitung

Furuno

Furuno DS-30 Bedienungsanleitung

Furuno

Furuno CH-37 Bedienungsanleitung

Furuno

Furuno CSH-5LMARK-2 Bedienungsanleitung

Furuno

Furuno CH-300 Bedienungsanleitung

Furuno

Furuno CI-60G Bedienungsanleitung

Furuno

Furuno CSH-8LMARK-2 Bedienungsanleitung

Furuno

Furuno CSH-5L Bedienungsanleitung

Furuno

Furuno COLOR SCANNING CSH-55 Bedienungsanleitung

Furuno

Furuno FSV-24 Bedienungsanleitung

Furuno

Furuno FCV-1200L Bedienungsanleitung

Furuno

Furuno FCV-1000 Bedienungsanleitung

Furuno

Furuno CSH-7 Bedienungsanleitung

Furuno

Furuno CI-68 Bedienungsanleitung

Beliebte Sonar Handbücher anderer Marken

Kongsberg

Kongsberg Simrad SP90 Series Bedienungsanleitung

Eagle

Eagle TriFinder 2 Bedienungsanleitung

Lowrance

Lowrance X-70A Bedienungsanleitung

Lowrance

Lowrance LMS-150 GPS Bedienungsanleitung

Simrad

Simrad EQ 55 Bedienungsanleitung

Lowrance

Lowrance Traditional Bedienungsanleitung

Teledyne

Teledyne BlueView BV3200 Bedienungsanleitung

Reson

Reson SeaBat 7125 SV2 Bedienungsanleitung

Eagle

Eagle 101 Bedienungsanleitung

IMAGENEX

IMAGENEX 881A-GS Bedienungsanleitung

Eagle

Eagle Z-15 Bedienungsanleitung

Simrad

Simrad SH80 - REV C Bedienungsanleitung

Simrad

Simrad ST90 Bedienungsanleitung

Hawk

Hawk Sultan Bedienungsanleitung

Lowrance

Lowrance 1240A Bedienungsanleitung

Kongsberg

Kongsberg Flexview Bedienungsanleitung

VEXILAR

VEXILAR 107 PRO Bedienungsanleitung

Klein

Klein 5000 V2 Series Bedienungsanleitung