FUTABA 16IZ Gebrauchs- und Pflegehandbuch

YourFutabaT16IZtransmitterprogrammingcanbeupdatedeasilyonline.Whenfunctionsareaddedorimproved,theupdatefilecanbedownloadedfromourwebsite.CopytheupdatefilestothemicroSDcardandthenusethefollowingproceduretoupdatetheprogram.CheckourwebsitefortheFAQregardingupdatingformoreinformation.HowtoupdateT16IZŸƓƇƄƗƌƑƊŃƓƕƒƆƈƇƘƕƈ

Note: If the battery fully discharges during

program updating, updating will fail. When

the remaining battery capacity is 50% or

less, always recharge the battery before

updating.

Note: The model data in the transmitter can

be used unchanged after updating, but to

be safe, back up the model data before

updating.

1. Download the zip file of the update data

from our website.

([WUDFWWKH]LSÀOHRQ\RXUFRPSXWHU

3. The "FUTABA" folder will be created on your

computer.

4. Copy the "FUTABA" folder into your microSD

card.

Note: If the microSD card has already had

"another FUTABA" folder before you make a

copy, the "FUTABA" folder is OVERWRITTEN.

5. Insert the microSD card with "FUTABA" folder

that contained the update software into the

SD card slot on your T16IZ radio transmitter.

6. Turn on the transmitter power while pressing

down the "HOME/EXIT" button. The update

screen appears on the LCD display of your

T16IZ and the software update is started.

FutabaWEB16IZUpdateZipﬁleDownloadCopythe"FUTABA"folderintoyourSDcard.InstalledmicroSDcardoftheupdateﬁlePresstheHOME/EXITswitchandturnonUpdating12

7. When the software update is completed,

"Completed" message is shown on the LCD

display of your T16IZ. (Show below picture.)

8. Turn off the power switch of your T16IZ and

remove the microSD card from the card slot.

Possible Problems

When one of the error messages shown

below appears on the LCD screen your

T16IZ, the software update will not be

completed.

"Low battery."

Software update is postponed because

of low battery. Retry the software update

after the battery is recharged.

8SGDWHÀOHQRWIRXQG

The T16IZ cannot find the update file on

the microSD card. Check to be sure all the

update files have been copied onto the

microSD card.

%URNHQÀOH

7KH7,=GHWHFWVWKHXSGDWHÀOHHUURU7KH

update file may be broken or for another

transmitter.

"Write error."

The software update procedure is stopped

for an unknown reason. Contact your local

service center when this error message

appears on the LCD screen of your T16IZ.

Don't absolutely remove the battery

and the microSD ca r d f r o m t h e

transmitter during the update.

There is a possibility that the transmitter

will be damaged.

Recovering a failed update

If you failed to update for any reason, it

may transmitter will not start.

In t hat case, please update again

transmitter in the following procedure.

1. Detach the battery from the transmitter.

2. Insert the microSD card that contained

WKHXSGDWHÀOHVWRWKHWUDQVPLWWHU

3. Attach the battery to the transmitter

while pressing down the "HOME/EXIT"

button.

4. The update will start.

Even af t e r t h e above s t e p s , if the

transmitter fails to update or does not

start, please have it serviced.

Complete

1M23Z07711T16IZSOFTWAREUPDATECHANGESV3.2V3V3.11. Compatible with Futaba ESC MC-980H/A, MC-9130H/A, MC-9200H/A

Supports the telemetry function of MC-980H/A, MC-9130H/A, and MC-9200H/A.

1. Fixed an issue where the Vario Melody settings were not saved.

1. Fixed telemetry voice for Futaba ESC and Hobbywing ESC.

2. Fixed the problem that model copy fails.

This software updates or alters the functions and features noted below. The instructions and information that follow are meant as a supplement to the original

instruction manual that accompanied the T16IZ transmitter. Please refer to the original instruction manual where applicable, but replace the steps indicated below with

these instructions. Please check to ensure that the update has been installed.

1) Select the System Menu.

2) Touch the [Information] button.

3) Conﬁrm that the information in the display indicates the version numbers as noted above.

◆RegistertheESCwithtransmitter.◆Alternatively,select[FutabaESC]instartslot24.◆TheregisteredESCwillbedisplayedas"FutabaESC".ConnectSBM-2totheS.I/Fportonthebackoftransmitter.◆Linkagemenu→Sensor→3/3Registrationtotransmitter●Callpage3of[Sensor].*Pleasenotethattheproperdefaultslotforthisaccessoryisnumber8(8-15).Thissensoruseseightslots.Beingmadetoastartslotare8,16,and24.Informationonhowtochangetheslotassignmentisincludedinthetransmitter'smanual.ConnecttheSBM-2tothetransmitterasshown,thentapRegister.CompleteregistrationandremoveSBM-2fromthetransmitter.◆The registered Hobbywing ESC is displayed as "Hobbywing ESC".

For details on Hobbywing ESC telemetry

support, refer to the Hobbywing website.

AlarmischosenfromBuzzer,Voice,andInhibit.AllowsSpeechtobeturnedONorOFF.↑Anupwardarrowindicatesthealarmwillsoundwhenthecurrentreachesaboveyoursetvalue.↓Adownwardarrowindicatesthealarmwillsoundwhenthecurrentreachesbelowyoursetvalue.*The current and capacity consumption display may vary

depending on the usage conditions, so use it as a guide.

◆ESC telemetry display screen

The ESC status is displayed. Alarm setting is also possible.

Displaymax/minvaluePressandholdtoreset.Displaymax/minvaluePressandholdtoreset.Taptomovetothecurrentsettingpage.Taptomovetothevoltagesettingpage.Taptomovetothecapacitysettingpage.Taptomovetotherotationsettingpage.Enterthenumberofpolesforyourmotor.Whenenabled,thealarmwillbeactivatedinthefollowingwarningstate.Ifthegearisdown,enterthegearratiotodisplaythehelicopterrotorspeedandtheairplanegeardownpropellerspeed.Whenenabled,thevibratorwillstartinthefollowingwarningstate.◆Warningstate◆AlarmscanbesetforVoltage,Capacity,Rotation,ESCtemperature,andThrottleusingthesameprocedure.ShowstheoutputlevelfromtheESCtothemotor,notthepositionofthethrottlestick.Evenifthestickisinthe50%position,theoutputmaynotbe50%dependingontheESCsetting.Throttlenotat0%LowvoltageOvertemperatureOvercurrentMotorlockedThrottlesignallostWhenthethrottlestickisnotlowwhenESCisstartedWhenthebatteryvoltageisbelowthecutoﬀvoltageWhentheESCtemperatureis110°CorhigherPeakcurrentoverWhenthemotorlocksWhennothrottlesignalisreceivedformorethan0.25sTaptomovetothetemperaturesettingpage.Taptomovetothethrottlesettingpage.◆MC-9130H/AtelemetryconnectionexampleSBM-2ESCToCH3TofreeportTodrivebatteryThrottleToS.BUS2◆AlarmsettingSetsthecurrentonwhichthealarmoperates.

V21. Add GYA553 Airplane Gyro setting function. (Refer the T16IZ GYA553 Setting Manual)

2. Compatible with SCORPION ESC telemetry

Added support for SCORPION POWER SYSTEM ESC some models.

©FUTABA CORPORATION 2021, 12

2. GYA553 Addition of setting parameters

AIL / ELE / RUD holding power setting has been added to the setting parameters of GYA553.

Adjusted the gyro holding force of the aircraft in AVCS mode.

Decreasing the value weakens the holding power and makes

the operation feeling closer to the Normal mode.

Inhaltsverzeichnis

Andere FUTABA Fernbedienung Handbücher

FUTABA

FUTABA 8FG Bedienungsanleitung

FUTABA

FUTABA 12FG Bedienungsanleitung

FUTABA

FUTABA T10J Bedienungsanleitung

FUTABA

FUTABA T14MZ Bedienungsanleitung

FUTABA

FUTABA 4PK-2.4GHZ Bedienungsanleitung

FUTABA

FUTABA T18SZ Bedienungsanleitung

FUTABA

FUTABA 12Z Series Bedienungsanleitung

FUTABA

FUTABA 2PC Bedienungsanleitung

FUTABA

FUTABA 3PJ Super Bedienungsanleitung

FUTABA

FUTABA T18SZ Bedienungsanleitung

FUTABA

FUTABA 16SZ Bedienungsanleitung

FUTABA

FUTABA 6k Bedienungsanleitung

FUTABA

FUTABA 4YF-2.4GHZ Bedienungsanleitung

FUTABA

FUTABA T32MZ Bedienungsanleitung

FUTABA

FUTABA 9z Installationsanleitung

FUTABA

FUTABA 3GR-2.4GHZ Bedienungsanleitung

FUTABA

FUTABA 4PK-2.4G SuperR Bedienungsanleitung

FUTABA

FUTABA T18MZ Bedienungsanleitung

FUTABA

FUTABA GV T2PG Bedienungsanleitung

FUTABA

FUTABA T18SZ Bedienungsanleitung

FUTABA

FUTABA 7C-2.4GHz Bedienungsanleitung

FUTABA

FUTABA 6YG-FM Bedienungsanleitung

FUTABA

FUTABA 2PL Bedienungsanleitung

FUTABA

FUTABA AZPT14SG-24G Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung