FUTABA 3GR-2.4G Bedienungsanleitung

3GR-2.4G

3-channel, FASST

Radio control system for Car

1M23N18005

Thank you for purchasing a Futaba 3GR-2.4GHz system.

Before using your 3GR-2.4GHz system, read this manual carefully in order to use your R/C set safely.

After reading this manual, store it in a safe place.

Application, Export, and Modification

1. This product may be used for models only. It is not intended for use in any application other than the

control of models for hobby and recreational purposes.

2. Exportation precautions:

(a) When this product is exported from the country of manufacture, its use is to be approved by the laws govern-

ing the country of destination for devices that emit radio frequencies. If this product is then re-exported to other

countries, it may be subject to restrictions on such export. Prior approval of the appropriate goverment authori-

ties may be required. If you have purchased this product from an exporter outside your country, and not the

authorized Futaba distributor in your country, please contact the seller immediately to determine if such export

regulations have been met.

(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, and

an application for export approval must be submitted.

3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized

modification, adjustment, and replacement of parts on this product. Any such changes may void the

warranty.

Compliance Information Statement (for U.S.A.)

This device, trade name Futaba Corporation of America, model number R603FF, complies with part

15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

TEL (217)398-0007 or E-mail: [email protected] (Service)

Battery Recycling (for U.S.A.)

The RBRCTM SEAL on the (easily removable) nickel-cadmium battery contained in

Futaba products indicates that Futaba Corporation of America is voluntarily participating

in an industry program to collect and recycle these batteries at the end of their useful

lives, when taken out of service within the United States. The RBRCTM program provides

a convenient alternative to placing used nickel-cadmium batteries into the trash or mu-

nicipal waste system, which is illegal in some areas.

You may contact your local recycling center for information on where to return the spent battery.

Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling in your area. Futaba Cor-

poration of America's involvement in this program is part of its commitment to protecting our environ-

ment and conserving natural resources.

RBRCTM is a trademark of the Rechargeable Battery Recycling Corporation.

Warning: This product contains a chemical known to cause cancer and birth defects (or other

reproductive harm).

•No part of this manual may be reproduced in any form without prior permission.

•The contents of this manual are subject to change without prior notice.

•This manual has been carefully written. Please write to Futaba if you feel that any corrections or clarifications

should be made.

•Futaba is not responsible for the use of this product.

For Your Safety As Well As That Of Others...........6

Explanation of Symbols ................................................................................ 6

2.4GHz System Precautions ......................................................................... 6

Operation Precautions .................................................................................. 7

NiCd Battery Handling Precautions ............................................................. 9

Storage and Disposal Precautions ............................................................ 10

Other Precautions ....................................................................................... 11

Table Of Contents

Before Using ...........................................................12

Features........................................................................................................ 12

Set Contents ................................................................................................ 14

Nomenclature (Transmitter/Receiver/Servo) ............................................ 15

Installation ..............................................................21

Receiver and Servo Connections .............................................................. 21

Installation Safety Precautions .................................................................. 21

Initial Set-Up ...........................................................23

How to link the transmitter and the receiver............................................. 23

Preparations (Transmitter) ......................................................................... 24

Functions ................................................................30

End Point Adjuster ...................................................................................... 30

Steering Speed ............................................................................................ 33

Steering EXP / Throttle EXP ....................................................................... 34

A.B.S. Function ............................................................................................ 36

Throttle Acceleration................................................................................... 38

Brake Mixing ................................................................................................ 40

Programmable Mixing ................................................................................. 41

Fail Safe/Battery Fail Safe (HRS System Only) ......................................... 42

Trim ............................................................................................................... 43

Steering D/R ................................................................................................. 44

ATL Function ............................................................................................... 44

Channel 3 Position ...................................................................................... 45

Subtrim ......................................................................................................... 46

Servo Reverse.............................................................................................. 47

Function Map ..........................................................28

(Function Selection) .................................................................................... 28

Model Select ...................................................................................... 48

Timer................................................................................................... 49

(System Functions)

Model Copy ........................................................................................ 51

Model Reset ....................................................................................... 52

Model Name ....................................................................................... 52

HRS/PPM Select ................................................................................ 53

Function Select Switch ..................................................................... 54

Function Select Lever ....................................................................... 55

Condition 2 Selection........................................................................ 56

LED Mode Selection .......................................................................... 56

Throttle Neutral Adjuster .................................................................. 57

For Your Safety

As Well As

That Of Others

Before

Using

Installation

Initial

Set-Up

Function

Map

Functions

Reference

Reference .........................................................58

Ratings ............................................................................................... 58

Optional Parts .................................................................................... 59

Troubleshooting ................................................................................ 60

Error Displays .................................................................................... 61

When requesting repair .................................................................... 62

For Your Safety As Well As That Of Others

Use this product in a safe manner. Please observe the following safety precautions at

all times.

Explanation of Symbols

The parts of this manual indicated by the following symbols are extremely important

and must be observed.

Danger

Indicates a procedure which could lead to a dangerous situ-

ation and may cause death or serious injury if ignored and

not performed properly.

Warning Indicates procedures which may lead to dangerous situa-

tions and could cause death or serious injury as well as su-

perficial injury and physical damage.

Caution Indicates procedures that may not cause serious injury, but

could lead to physical damage.

Symbols: ; Prohibited ; Mandatory

Symbols Explanation

Special attention should be paid before turning on the system while other cars are run-

ning or other airplanes are flying because the 2.4GHz RC system could potentially af-

fect them.

Warning

2.4GHz System Precautions

Prohibited Procedures

Always use R603FF under the following conditions;

Power supply: 6V Nicd battery (PPM/HRS mode)

Servo: 6V type Futaba Digital Servo (HRS mode)

If these conditions are not followed, control may be impossible or the servo may be damaged.

Caution

Mandatory Procedures

For Your Safety As Well As That Of Others

Operation Precautions

Warning

Prohibited Procedures

Do not operate outdoors on rainy

days , run through puddles of water,

or use when visibility is limited.

Should any type of moisture (water or snow) enter any

component of the system, erratic operation and loss

of control may occur.

Do not operate in the following

places.

-Near people or roads.

-On any pond when boats are present.

-Near high tension power lines or communi-

cation broadcasting antennas.

Interference could cause loss of control. Improper in-

stallation of your Radio Control System in your model

could result in serious injury.

Do not operate this R/C system when

you are tired, not feeling well or under

the influence of alcohol or drugs.

Your judgment is impaired and could result in a dan-

gerous situation that may cause serious injury to your-

self as well as others.

Mandatory Procedures

Adjust the antenna vertically to the ground.

Otherwise, the operating range may become shorter.

Always perform an operating range check prior to use.

Problems with the radio control system as well as improper installation in a model could cause loss of control.

Simple range test method;

Have a friend hold the model, or clamp it down or place it where the wheels or prop cannot come in contact with any

object. Walk away and check to see if the servos follow the movement of the controls on the transmitter. Should you

notice any abnormal operation, do not operate the model. Also check to be sure the model memory matches the

model in use.

Caution

Prohibited Procedures

Do not touch the engine, motor, speed control or

any part of the model that will generate heat while

the model is operating or immediately after its use.

These parts may be very hot and can cause serious burns.

Never hold only the an-

tenna.

Hold the grip handle, otherwise the

antenna may be damaged.

Mandatory Procedures

When making adjustments to the model, do so with the engine not running or the motor

disconnected.

You may unexpectedly lose control and create a dangerous situation.

For Your Safety As Well As That Of Others

(Turning on the power switches)

Always check the throttle stick on the transmitter to be sure it is at the neutral position.

1. Turn on the transmitter power switch.

2. Turn on the receiver or speed control power switch.

(Turning off the power switches)

Always be sure the engine is not running or the motor is stopped.

1. Turn off the receiver or speed control power switch.

2. Then turn off the transmitter power switch.

If the power switches are turned off in the opposite order the model may unexpectedly run out of control and cause

a very dangerous situation.

(Fail safe function) ---when using HRS mode

Before running (cruising), check the fail safe function.

Check Method:

Before starting the engine, check the fail safe function as follows:

1. Turn on the transmitter and receiver power switches.

2. Wait at least one minute, then turn off the transmitter power switch. (The transmitter automatically transfers the fail

safe data to the receiver every minute.)

3. Check if the fail safe function moves the servos to the preset position when reception fails.

The fail safe function is a safety feature that minimizes set damage by moving the servos to a preset position when

reception fails. However, if set to a dangerous position, it has the opposite effect.

Setting example: Throttle idle or brake position

For Your Safety As Well As That Of Others

NiCd Battery Handling Precautions

(Only when NiCd batteries are used)

Warning

Mandatory Procedures

Always check to be sure your batter-

ies have been charged prior to oper-

ating the model.

Should the battery go dead while the model is operat-

ing, loss of control will occur and create a very dan-

gerous situation.

To recharge the transmitter and/or re-

ceiver NiCd batteries, use the special

charger made for this purpose.

Overcharging could cause the NiCd battery to over-

heat, leak or explode. This may lead to fire, burns,

loss of sight and many other types of injuries.

Caution Prohibited Items

Do not use commercial AA

size NiCd batteries.

Quick charging may cause the

battery contacts to overheat and

damage the battery holder.

Do not short circuit the NiCd battery

terminals.

Causing a short circuit across the battery terminals

may result in abnormal heating, fire and burns.

Do not drop the NiCd battery or ex-

pose it to strong shocks or vibrations.

The battery may short circuit and overheat. Electrolyte

may leak out and cause burns or chemical damage.

When the model is not being used,

always remove or disconnect the

NiCd battery.

Leaving the battery connected could create a dangerous

situation if someone accidentally turns on the receiver

power switch. Loss of control would occur.

Special

Charger

Shock

Prohibited

NiCd AA size

batteries.

Use

prohibited

Do not throw NiCd batteries into a

fire. Do not expose NiCd batteries to

extreme heat. Also do not disas-

semble or modify a NiCd battery

pack.

Overheating and breakage will cause the electrolyte

to leak from the cells and cause skin burns, loss of

sight as well as other injuries.

When the system will not be used for

any length of time store the system

with batteries in a discharged state.

Be sure to recharge the batteries prior

to the next time the system is used.

If the batteries are repeatedly recharged in a slightly

discharged state the memory effect of the NiCd bat-

tery may considerably reduce the capacity. A reduc-

tion in operating time will occur even when the batter-

ies are charged for the recommended time.

The electrolyte in NiCd batteries is a strong alkali. Should you get even the smallest amount of the

electrolyte in your eyes, DO NOT RUB. Wash immediately with water and seek medical attention at

once. The electrolyte can cause blindness. If electrolyte comes in contact with your skin or clothes,

wash with water immediately.

Prohibited Items

For Your Safety As Well As That Of Others

Storage and Disposal Precautions

Warning

Prohibited Procedures

Do not leave the radio system or models within the reach of small children.

A small child may accidentally operate the system. This could cause a dangerous situation and injuries. NiCd

batteries can be very dangerous when mishandled and cause chemical damage.

Caution

Prohibited Procedures

Do not store your R/C system in the

following places.

- Where it is extremely hot or cold.

- Where the system will be exposed to direct

sunlight.

- Where the humidity is high.

-Where vibration is prevalent.

-Where dust is prevalent.

-Where the system would be exposed to

steam and condensation.

Storing your R/C system under adverse conditions

could cause deformation and numerous problems

with operations.

Mandatory Procedure

If the system will not be used for a

long period of time, remove the bat-

teries from the transmitter and model

and store in a cool, dry place.

If the batteries are left in the transmitter, electrolyte

may leak and damage the transmitter. This applies to

the model also. Remove the batteries from it also to

prevent damage.

A used NiCd battery is valuable resource. Insulate the battery terminals and dispose of the battery by

taking it to a battery recycling center.

Inhaltsverzeichnis

Andere FUTABA Fernbedienung Handbücher

FUTABA

FUTABA T16IZ Bedienungsanleitung

FUTABA

FUTABA 8J Bedienungsanleitung

FUTABA

FUTABA T18MZ Technisches Handbuch

FUTABA

FUTABA 4PK 2.4GHZ Installationsanleitung

FUTABA

FUTABA SKYSPORT-6A Bedienungsanleitung

FUTABA

FUTABA FASSTest-2.4GHz T16SZ Series Bedienungsanleitung

FUTABA

FUTABA 12FG Bedienungsanleitung

FUTABA

FUTABA 9z Installationsanleitung

FUTABA

FUTABA 9VAP Bedienungsanleitung

FUTABA

FUTABA Magnum Sport FP-S148 Bedienungsanleitung

FUTABA

FUTABA ATTACK Bedienungsanleitung

FUTABA

FUTABA T12K Technisches Handbuch

FUTABA

FUTABA 9ZAP - PART1 Bedienungsanleitung

FUTABA

FUTABA GYA460 Bedienungsanleitung

FUTABA

FUTABA 3GR-2.4GHZ Bedienungsanleitung

FUTABA

FUTABA FP-G134 Bedienungsanleitung

FUTABA

FUTABA SBC-1 Bedienungsanleitung

FUTABA

FUTABA T6L SPORT Bedienungsanleitung

FUTABA

FUTABA 3PM-X 2.4GHZ Bedienungsanleitung

FUTABA

FUTABA 6YG-FM Bedienungsanleitung

FUTABA

FUTABA R6014FS Bedienungsanleitung

FUTABA

FUTABA T10PX Montageanleitung

FUTABA

FUTABA 4PK-2.4GHZ Bedienungsanleitung

FUTABA

FUTABA 3pv-2.4g Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung