FUTABA T14SG Technisches Handbuch

T14SG SOFTWARE UPDATE MANUAL

[Updating procedure]

1. SD card format

1. You will rst want to format your SD card to the 14SG. If you are using an existing

SD card, any data previously saved to it will be deleted during the "format". We

suggest you either save this data on your computer or purchase a new card.

2. After inserting the new SD card into the transmitter, turn

on the power switch. You will see the word "FORMAT" if

you have not previously used this card in the transmitter.

3. Please select "YES" and touch “RTN” .

4. The following screen is displayed during

formatting.

5. When the format is completed, the following screen is

displayed.

6. Turn o the power switch and remove the SD card from

its slot.

2. Preparing the software update card.

1. Please unzip the zipped le. The following les will be created.

・T14sgUpdate.exe ... File copy utility

・T14sgUpdate.dat ... Information le for T14sgUpdate.exe

・T14SG_UPDATE.dat … Identied le of T14SG

・T14SG_TS.bin ... Update le of T14SG (piece 3)

・T14SG_AP.bin ... Update le of T14SG (piece 2)

・T14SG_UPLD.bin ... Update le of T14SG (piece 1)

① Push to open.

②Slide in the direction of the

arrow on the battery cover.

③ Battery cover will open downward. ④ Insert the SD card in the

slot as shown above.

SD card slot

-1-

2. Insert the 'formatted" SD card into a card reader in your PC.

3. Please run "T14sgUpdate.exe".

4. Select the drive that your card reader is

assigned to in your PC.

5. After the Update les are copied to the SD card, the following screens are displayed.

Click the "End" button.

Update

-2-

3. Update software of T14SG

1. Please insert the SD card which includes the update le.

2. Push the HOME/EXIT button.

3. While still holding the HOME/EXIT button, power

on the transmitter.

4. After a few seconds, the following screen is displayed.

5. Push the U.MENU/MON. button for three

seconds. The software update will begin.

6. When the update is complete, the following screen is

displayed. Turn o the power switch.

7. Remove the SD card.

8. Please check the software version at INFO in SYSTEM

menu.

HOME/EXIT

button

U.MENU/MON.

button

PROGRAM UPDATE

START : PUSH MON . 3SEC

PROGRAM UPDATE

UP LOADING

-3-

PROGRAM UPDATE

COMPLETED

T14SG Installing Speech Data

Before installing the speech data, you will need to update your T14SG software to

Version 2.0 or later.

If the software version of T14SG is before Ver.2.0, the speech data can not be installed.

There are three language versions, English, German, and Japanese, in speech data. It is

possible to install only one language.

If you install a second language, it will override the rst one that you installed.

[Installing procedure]

1. Making of card for installing speech data

1. Please unzip the zipped le. The following les will be created.

English Version

・T14sgInstallSoundEng.exe ... File copy utility

・T14sgUpdate.dat ... Information le for T14sgInstallSoundEng.exe

・T14SG_INSTALL_SOUND.dat … Identied le

・T14sgSpeechEng1.bin ... Data le (piece 1)

・T14sgSpeechEng2.bin ... Data le (piece 2)

・T14sgSpeechEng3.bin ... Data le (piece 3)

German Version

・T14sgInstallSoundEng.exe ... File copy utility

・T14sgUpdate.dat ... Information le for T14sgInstallSoundEng.exe

・T14SG_INSTALL_SOUND.dat … Identied le

・T14sgSpeechGer1.bin ... Data le (piece 1)

・T14sgSpeechGer2.bin ... Data le (piece 2)

・T14sgSpeechGer3.bin ... Data le (piece 3)

Japanese Version

・T14sgInstallSoundEng.exe ... File copy utility

・T14sgUpdate.dat ... Information le for T14sgInstallSoundEng.exe

・T14SG_INSTALL_SOUND.dat … Identied le

・T14sgSpeechJpn1.bin ... Data le (piece 1)

・T14sgSpeechJpn2.bin ... Data le (piece 2)

・T14sgSpeechJpn3.bin ... Data le (piece 3)

-4-

2. Install the already formatted SD card into your PC's card reader.

3. Please run "T14sgInstallSound***.exe".

4. Select the drive that your card reader is

assigned to in your PC. Click "OK".

5. After the Update les are copied to the SD card, the following screens are displayed.

Click the "End" button.

Update

-5-

2. Install speech data of T14SG

1. Please insert the SD card which includes the installing speech data.

2. Push the HOME/EXIT button.

3. Still holding the HOME/EXIT button, power

on the transmitter.

4. After a few seconds, the following screen is displayed.

5. Press the U.MENU/MON. button for three seconds. The

speech data begins to install.

6. After about 16 seconds, uploading reaches the right of the

progress bar, and then begins again after a pause.

7. The uploading may appear to progress slowly.

8. The progress bar will again upload. This can take a few

minutes.(About. 2 min.)

And, “COMPLETED” is displayed. Please turn o the power.

(Don't turn o the power before COMPLETED is

displayed.)

9. Please detach SD card.

10. Please check the language at TELEM.SET. menu in LINKAGE menu.

HOME/EXIT

button

U.MENU/MON.

button

INSTALLSOUND

START : PUSH MON . 3SEC

INSTALLSOUND

INSTALLING

INSTALLSOUND

INSTALLING

-6-

INSTALLSOUND

COMPLETED

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

©FUTABA CORPORATION 2013, 8 (1)

- 1 -

T14SG Software Update Changes

(Version 2.0)

This software update modies features found on the 14SG. If you have questions about these updated directions,

please consult your instruction manual or futaba-rc.com for further details. Refer to the original manual where

applicable but replace the steps indicated below with these instructions.

1.TELEMETRY MONITOR

The telemetry screen is modied.

● TELEMETRY MONITOR set up

① The HOME/EXIT button is pushed from

HOME screen and TELEMETRY MONITOR

is called.

② Move the cursor to the "RECEIVER" or

"SENSOR" (SBS-XXX etc.) and touch the

RTN button.

③ You will use the "Display" function to

choose how many sensors are shown on

your Telemetry monitor.

It pushes from

HOME screen.

To TELEMETRY MONITOR

You can display any items on the telemetry screen

up to 4 items at FASSTest 14CH mode. The benet

of expansion of a character will be obtained by

choosing the display items 1 and 2.

Ex. 1 item is displayed Ex. 2 items are displayed

Ex. 4 items are displayedEx. 3 items are displayed

If the numeric part

(included "+","-",",")

is over the 6 letters, it

becomes the smaller size

automatically. It is same

size as 2 items screen.

In FASSTest12CH mode,

they are only 1 and 2 item

displays.

If a cursor is moved to items (Rx-BATT,

EXT-VOL, TEMP. etc.) and RTN is touched,

the alarm setting screen of the item will be

displayed.

1 3

2 4

[ Display position ]

The Telemetry Monitor is accessed by a quick tap of the HOME/EXIT key. Do not press and hold as this

will activate Key Lock.

Key-Lock

Lock or unlock is done either by pressing and holding the S1 key or by pressing and holding the HOME/EXIT key.

- 2 -

④ If you want to show two sensors on your

Telemetry screen, select 2 in "Display".

Then move down to the Sensor to select

which other item is shown.

⑤ If you want to show three sensors

on your Telemetry screen, select 3

in "Display". Then move down to the

Sensor to select which other item is

shown.

⑥ To SENSOR " ----------" selection will

reduce a display item.

2. Telemetry Speech function

■ There is not only a software update, but also a

Speech update that must be done.

■ There are two languages available in the

Speech data, English and German.

■ The language chosen for the Speech data will

affect only the Speech function. It will not

change the language used in the transmitter's

text display.

■ The Speech function can only be used with

headphones plugged into the phone jack.

■ You will need to purchase headphones or

earphones with a 3.5plug.

● TELEM.SET. menu is added to the

LINKAGE MENU.

When using a sensor that has two or more

functions, you will want to scroll to select

which will be displayed. (ALTITUDE,VARIO,

etc.)

1 3

The speech language installed is

indicated.　When the speech data is

not installed, "----------" is displayed.

The version No. of the speech data

file is indicated.　When the speech

data is not installed, nothing is

displayed.

The interval of speech can be set.

The setting range is from 0 [Sec] to

30 [Sec].

Earphone plug

- 3 -

● The phone volume is added to SOUND

menu in SYSTEM MENU.

● The vario melody outputs from the

phone jack.

● ACT/INH button and ON/OFF switch

button of the speech function are added

to the telemetry alert screen.

● When the telemetry alert occurred, the

speech function works.

*The format of the speech output is

[sensor type］[data］［unit]［data］［data］［data］［data］

Ex. Rx battery

「battery」「seven point four」「volt」「seven point

four」「seven point four」「seven point four」「seven

point four」

*If the telemetry data is changed frequently, the

speech data will not be the same as the displayed

data.

*The format of the speech output is

"warning" [sensor type］[data］［unit］

Ex. Rx battery

「warning」「battery」「four point zero」「volt」

*If the telemetry data is changed frequently, the

speech data will not be the same as the displayed

data.

The priority of the phone output is below;

Speaking Alarm >> Speaking data >> Vario Melody

The setting range is from 0 to 30.

0 is silence.

When the speech function is valid, "on" is displayed.

When the speech function is INH or the switch is off,

nothing is displayed.

The speech function does not work when the

telemetry data is not received, even if "on" is

displayed.

ACT/INH button ON/OFF button

When the ALERT button is ACT, the

speech function works when the alert

occurs.

When the melody function

is active, the vario melody

outputs from the phone jack.

(High priority) (Low priority)

3. The setting range of the threshold of

temperature sensors is modied.

-19 ℃ ～ 200 ℃ ( ↑ THRESHOLD >

↓THRESHOLD)

at both of SBS-01T and Temp125

-20 ℃ ～ 199 ℃ ( ↑ THRESHOLD >

↓THRESHOLD)

at both of SBS-01T and Temp125

- 4 -

subject to change without prior notice. While this manual has been carefully written, there may be inadvertent errors or omissions.

Please contact our service center if you feel that any corrections or clarications should be made.

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

©FUTABA CORPORATION 2013, 8 (1)

Andere Handbücher für T14SG

Inhaltsverzeichnis

Andere FUTABA Fernbedienung Handbücher

FUTABA

FUTABA FP-3EG Bedienungsanleitung

FUTABA

FUTABA 8FG Bedienungsanleitung

FUTABA

FUTABA 14MZ Bedienungsanleitung

FUTABA

FUTABA FP-2GS Bedienungsanleitung

FUTABA

FUTABA T18MZ Bedienungsanleitung

FUTABA

FUTABA T16IZ Handbuch

FUTABA

FUTABA T10PX Montageanleitung

FUTABA

FUTABA 7PX Bedienungsanleitung

FUTABA

FUTABA 8FG Bedienungsanleitung

FUTABA

FUTABA 1M23N20718 Bedienungsanleitung

FUTABA

FUTABA 3PDF Bedienungsanleitung

FUTABA

FUTABA T18SZ Bedienungsanleitung

FUTABA

FUTABA Mega Tech 3PK Bedienungsanleitung

FUTABA

FUTABA 10CAP Bedienungsanleitung

FUTABA

FUTABA 4EXA Bedienungsanleitung

FUTABA

FUTABA FP-5NLK Bedienungsanleitung

FUTABA

FUTABA FP-8GHP Bedienungsanleitung

FUTABA

FUTABA 32MZ Bedienungsanleitung

FUTABA

FUTABA 12FG Bedienungsanleitung

FUTABA

FUTABA T12FG Technisches Handbuch

FUTABA

FUTABA FP-7UAF Bedienungsanleitung

FUTABA

FUTABA FP-S130 Bedienungsanleitung

FUTABA

FUTABA PCM1024H Bedienungsanleitung

FUTABA

FUTABA 3PRKA Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung