FUTABA CIU-2 S-Link Bedienungsanleitung
USB INTERFACE
Instruction Manual
USB port
Thank you for purchasing a CIU-2.
The CIU-2 is a USB interface for communications between Link supported devices and a Windows
computer.
Connecting and disconnecting the PC and CIU-2
1M23N19202
*Windows is registered trademark of Microsoft Corporation.
Notes
sPlease read this manual thoroughly before using your CIU-2.
sStore this manual in a safe place where it can be accessed at any time.
Drivers and Link programs must be installed.
sTo use the CIU-2, drivers must be installed.
sFor communication and setting, Link programs corresponding to each device must be installed.
Install the drivers and Link programs available on the dealer’s website.
Connection
1.Turn on the PC power.
2.Connect the CIU-2 to the USB port of the PC.
3.When the CIU-2 is first connected to the PC;
the “Found New Hardware Wizard” shown at
the right is displayed. Install the drivers
downloaded from the dealer’ s website.
Disconnection
The CIU-2 can be disconnected even while the
PC power is on. However, do not disconnect
the CIU-2 while it is communicating with a Link
supported device.
sReproduction of all, or part, of the contents of this manual without prior written permission is
prohibited.
sThe contents of this manual are subject to change without prior notice.
sThe contents of this manual should be complete, but if you find any errors or unclear points, please
contact us.
sFutaba will not be responsible for the results of use of devices by the customer.
Specifications
(Specifications and ratings are subject to change without prior notice accompanying technological developments.)
sInterface : USB Rev1.1 compliant
sUSB connector : USB Series A connector
sOperating voltage : 5.0V ±0.2V (USB bus power)
sCurrent drain
(At connection, idle): 12.3 ±2.0mA
*The PC must have a USB port (Type A).
sOperating environment:
Temperature -10 ~ 50degrees Celsius
sDimensions : 18.2 X 56.5 X 9.0 mm
sWeight : 7.5g
sApplicable OS : Windows Vista/XP/2000
*A 500mm extension
cord is supplied with
the CIU-2.
Connection method
1.Connect the CIU-2 to the USB port
of the PC.
2.Connect the Link supported device
to the CIU-2.
3.Connect the batteries by referring
to the Link supported device
instruction manual.
4.Set the power switch of the Link
supported device to ON.
5.Communication with the Link
program is possible.
Example of connection to Link supported device
(The figure below is an example of connection to an MC850C.)
Usage Precautions
Do not disassemble the CIU-2. Do not open the CIU-2 case.
Opening the case may damage the PC board. In this case, PC assembly replacement or repair will become
impossible. There is also the danger of fire and electric shock.
Do not expose the CIU-2 to water or other liquids. Do not touch the CIU-2 when you hands are
wet.
Water droplets entering the CIU-2 may cause trouble. There is also the danger of fire and electric shock.
Do not drop or expose the CIU-2 to strong shock.
It may cause trouble.
Do not set anything on top of the CIU-2.
It may cause trouble.
Do not touch the connectors with your hands. Also, do not connect a dusty or dirty connector.
It may cause trouble.
Handle the PC and peripheral devices in accordance with the instruction manual and cautions
and warnings given in the instruction manual of each product.
Connect to PC USB port
Power switch
Connects the connector of
the Link supported device.
Connect the batteries to
the Link supported device
When connecting, use the accessory 500m
extension cord, as required
.
Special Markings
Pay special attention to the
safety at the parts of this
manual that are indicated by
the following marks.
Mark Meaning
Procedures which may lead to a dangerous condition or cause death or serious
injury to the user if not carried out properly, or procedures where the probability of
superficial injury or physical damage is high.
Procedures where the possibility of serious injury to the user is small, but there is a
danger of injury, or physical damage, if not carried out properly.
Symbol: :Prohibited
:Mandatory
<When requesting repair>
Before requesting repair, read this instruction manual again. When there is an abnormality, request repair to your local
Futaba dealer.
©FUTABA CORPORATION 2007,05 (1)
FUTABA CORPORATION Makuhari Techno Garden Bldg., B6F 1-3 Nakase, Mihama-ku, Chiba 261-8555, Japan
Phone: (043) 296-5119 Facsimile: (043) 296-5124
Andere Handbücher für CIU-2 S-Link
1
Inhaltsverzeichnis
Andere FUTABA USB-Schnittstelle Handbücher
Beliebte USB-Schnittstelle Handbücher anderer Marken
PASCO
PASCO SCIENCEWORKSHOP 750 Bedienungsanleitung
Phonic
Phonic FIREFLY 302 USB Bedienungsanleitung
OHAUS
OHAUS Scout STX Series Bedienungsanleitung
Denon
Denon DN-HC4500 - DJ Mixer USB Controller Bedienungsanleitung
Lutron Electronics
Lutron Electronics Stanza SZ-CI-USB-CPN5138 Bedienungsanleitung
Paradox
Paradox PMC5-TI00 Bedienungsanleitung
Thorsis Technologies
Thorsis Technologies isDNet USB Bedienungsanleitung
Thorsis Technologies
Thorsis Technologies isHRT USB Bedienungsanleitung
microHAM
microHAM DigiKeyer Bedienungsanleitung
Apogee
Apogee Jam X Bedienungsanleitung
RigExpert
RigExpert TI-3000 Bedienungsanleitung
microHAM
microHAM USB Interface II Bedienungsanleitung