G-Tek BTG-100 Bedienungsanleitung
1
Table of Contents
Introduction……………………………………………………………………..3
Installation……………………………………………………………………....6
Pairing Bluetooth headset with the Gateway……………………………..8
Making a call…………………………………………………………………….8
Answering a call………………………………………………………………10
Pairing with Multiple Headsets……………………………………………..10
Specifications………………………………………………………………….11
Troubleshooting………………………………………………………………12
First edition (April 2004)
Corrections, changes and improvements to this manual might be made at any time and without notice. Such update
will, however, might be incorporated into new edition of this manual. The manufacturer assumes no responsibility or
reliability for any error or inaccuracy that may appear in this user guide.
All rights reserved.
Bluetooth is trademark of the Bluetooth SIG, Inc. The trademark are owned by Bluetooth SIG, Inc. USA
2
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and use in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
zConsult the dealer or an experienced radio/TV technician for help.
zYou are cautioned that changes or modifications not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment.
3
A. Introduction
Thank you for your purchase of BTG-100, Bluetooth Phone Audio Gateway. Your BTG-100
enables convenient cordless communication with analogue landline phone and Bluetooth
headset that are compliant with Bluetooth version 1.1 (or higher) and support the headset
profile.
Bluetooth technology make wireless link between any compatible mobile and stationary
communication devices. The technology adopts a global available RF frequency range to
establish RF link that offer secure, fast and reliable transmission of voice and data.
This user guide is intended to help you set up the gateway and to quickly familiarize
yourself with its operations. This document will guide you through the installation and
provide you with instructions on how to use the gateway’s features.
What is inside the box
The following items should be in your giftbox that comes with the Bluetooth Phone Audio
Gateway. If an item is missing, please contact your dealer.
Quantity Description
BTG-100 Bluetooth Phone Audio Gateway for house phone * 1
Linear AC Power Adapter with cord * 1
Phone cord * 1
User Manual * 1
Quick Start Guide * 1
It is recommended to use the power supply provided, otherwise there is risk of damaging the
Bluetooth phone audio gateway.
PICTURES of ITEMS in the BOX
BTG-100 Audio Gateway Linear AC Power Adapter RJ-11 Phone cord
4
Product Overview
5
Top View
Pairin
g
Button
LED 2/Power LED (Blue)
- Blue on while in Talk Mode
- Blue flashes as in Standby Mode pairing failed
LED 1/Pairing LED (Red)
Red flashes while Pairing
Mode starts or during Phone
Rings
A
ntenna
Rear View
VR (Variable Resistor)
for transmitter
gain adjustment
DC
Jack
RJ-11
Jack for
Analog
Landline
RJ-11
Jack for
Phone Line
B. Installation
Follow the procedures below to hook up your Gateway to your phone, cordless or otherwise.
This would allow you to receive or make call with your Bluetooth headset through a regular
phone line. This also frees you from being restrained by the length of your phone
cord during conversation.
1. Un-hook the original phone line from the phone.
2. Hook up the Gateway by RJ11 port marked “PHONE” to your landline phone using the
phone cord provided in the giftbox.
3. Hook up the original phone line to another phone jack marked “LINE” (RJ11 next to the
power jack) on the Gateway
6
4. Verify if working range of your AC power adapter input voltage complies to local receptacle
output voltage.
5. Plug the AC power adapter to the DC power Jack of Gateway and plug the leads of AC
power adapter to a receptacle that provides corresponding power source.
6. The LED Indicator start to flashes blue after power on.
7
8
C. Pairing Bluetooth Headset with the Gateway
1. Make sure the Gateway is powered on and is in idle mode. That is, LED indicator
should be blinking every two (2) seconds.
2. Set the Bluetooth headset in its “pairing mode”. Please refer to your headset manufacturer
user documentation on pairing for the proper procedures.
3. The Passkey (Pin Code) of the Gateway has been pre-stored in factory as 0000.
4. Make sure your Bluetooth headset’s PIN code is the same as the Gateway has.
5. Press the “Pair” button on the Gateway and release, LED indicator start blinking red
Within a few seconds, then LED Indicator shall flash both red and blue at the same time for
a very short moment, which indicates the pairing process are completed. You can also
check your headset LED to verify the status.
6. After pairing has completed, Gateway returns to the idle mode regardless of whether
pairing has been successful or not. The LED indicator should flash blue every two seconds.
Remark : 1 It is recommends that proceed pairing in a secured arena.
2 The Gateway can be paired with up to 4 different headsets. The 5th pairing removes the
memoryofthe1stone.
3. After paired successfully, the gateway will keep this pairing ID in memory even power
off. Once power on again, it work with paired device without re-pairing.
D. Making a Call
1. If your headset supports Multi-Device ID Switch (e.g. BTH-101) then select the line
9
switch to the gateway’s ID number; or if your headset does not support such switch and
has been paired with the Gateway only, press and release the headset’s talk button once
to ascertain that the Gateway goes off hook. LED indicator on the Gateway should light
steady blue. Skip to 3.
2. If your headset does not support the switch function in 1, and you need your headset
to be paired with more than one device (e.g. the gateway and your mobile phone),
please pair the Gateway lastly. press and release the headset’s talk button once to
ascertain that the Gateway goes off hook. LED indicator on the Gateway should light
steady blue. Skip to 3.
3. Lift the handset of phone, upon hearing a dial tone from the headset, you should key in the
numbers that you want to dial using the keypad on your phone, then, wait for the ringing
tone.
4. When you are done with your conversation, press and then release the talk/end button on
the headset once to terminate the call. The Gateway would then return to idle mode.
Remark : You can also proceed 3 and then 1 to make phone call. That is to usthe dialing pad on the
landline phone to dial the numbers first then press the Talk Button on the Bluetooth headset,
the landline phone will hand over the ring tone or voice if getting through. Hang up the
handset and start to talk or wait from the Bluetooth headset.
10
E. Answering a Call
1. Make sure the headset, which has been paired with the Gateway, is powered on, in
stand-by mode and within the working radius of each other.
2. When receive call, you hear a ringing tone in your headset and the Gateway LED indicator
shall blinks red, press the talk button once to answer the call. The Gateway will go off-hook
almost immediately. Gateway LED indicator shall light steady blue while phone call going.
3. When you are done with your conversation, press the talk button on the headset
once to terminate the call, and the Gateway will go back to idle mode.
F. Pairing With Multiple Headsets
The Gateway could be paired with up to four (4) headsets at one time. Headsets that are
paired with the Gateway thereafter would replace those of the previous 4’s, starting with the
first, followed by the second, and so forth. Once paired with the Gateway, headsets could
make calls at freedom any time without having to re-pair again, as long as these headsets,
except those headsets supporting Multi-Device ID Switch(e.g. BTH-101), do not pair with
other Bluetooth devices such as the Bluetooth enabled mobile phones afterwards. Normal
headset without Multi-Device ID Switch function that pairs with another Bluetooth device
after it has paired with the Gateway would have to re-pair with the Gateway before it could
again initiate outgoing calls.
Inhaltsverzeichnis
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
