Galaxy GS-105HS Bedienungsanleitung
1
Operation Manual
(GS-105HS)
Safety Instructions
When using your heat press,
basic precautions should be followed,
including the following:
1. Read all instructions.
2. Use heat press only for its intended use.
3. To reduce the risk of electric shock, do not immerse the heat press in water or
other liquids.
4. Never pull power cord to disconnect from outlet, instead grasp plug and pull to
disconnect.
5. Do not allow power cord to touch hot surfaces, allow heat press to cool completely
before storing.
6. Do not operate heat press with a damaged cord or if the equipment has been
dropped or damaged. To reduce the risk of electric shock, do not disassemble or
attempt to repair the heat press. Take it to a qualified service person for
examination and repair. Incorrect assembly or repair could increase the risk of fire,
electric shock, or injury to persons when the equipment is used.
7. This appliance is not intended to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
8. Close supervision is necessary for any heat press being used which can be sure
to keep children away from the equipment. Do not leave equipment unattended
while connected.
9. Burns can occur when touching hot metal parts.
10. To reduce the likelihood of circuit overload, do not operate other high voltage
equipment on the same circuit.
11. If an extension cord is necessary, then a 20-amp rated cord should be used.
Cords rated for less amperage may overheat. To arrange the cord in a correct way
so that it cannot be pulled or tripped over.
2
Table of Contents
Safety Instructions……………………….1
Technical Parameters……………………3
Machine View…………………………….4
Control Panel Guide……………………...5
Operating Instructions……………………6-10
⚫Assemble the Control Box……………………………………………6
⚫Connecting the System……………………………………………....7
⚫Ramspin system (Auto& Manual switch) …………………………...7
⚫Turning the System On…………………………………….…………8
⚫Adjusting the Temperature…………………………………………...8
⚫Adjusting the Time………………………………………………….....8
⚫Adjusting the Pressure………………………………………………..9
⚫Printing and Pressing………………………………………………....9
⚫Counter Setting………………………………………………………..9-10
⚫Switch Between F/C…………………………………………………..10
⚫Temperature Calibration……………………………….………………10
Exploded Views and Parts List…………12-16
Electrical Schematic……………………..17
3
Technical Parameters (GS-105HS)
Model:
GS-105HS-1620
Heater Size:
16’’×20’’
Pressure Display：
Yes
Auto Open：
Yes / Can also be setup as a Manual
Operation Press
Slide-out Lower Platen：
Yes
Power(110volt)
1800W/16.4Amps
Temperature Range：
Max. 430℉/ 221℃
Heating Up Time（180℃）
20 minutes
Time Range：
0~999S
Platen Exchange System
“Ramlock”quick change system
Optional Lower Platens (*Sold
Separately)
4’’×4’’
11’’×15’’
8’’×10’’
6’’×20’’
6’’×10’’
15” ×15”
Size (open) ：
29.5”x 16.9”x 39.3”
Packing Size：
33.1”x 20.5”x 23.4”
Packing Weight：
119.0lbs
Certificate：
CE, FCC
Machine View
4
5
Control Panel Guide
Operation Instructions
6
Assemble the Control Box
1. ASSEMBLE THE CONTROL BOX
1.1 Take out control box inside of the
packing carton, then place the control
box on top of the machine in the right
position. (figure 1.1)
1.2 Fasten the control box onto the
machine with 4 screws tightly. (figure
1.2)
1.3 Connect 5 phase aviation plug and 2
phase aviation plugs, then fasten
tightly. (figure 1.3)
ATTNTION: the aviation plug must be
connected tightly. (figure 1.4)
CAUTION
A sway connector will cause burning.
Ensure the connector is secure.
7
Connecting the System
2. CONNECT THE POWER CORD
2.1 Connect the power cord into a properly grounded electrical outlet with a sufficient
amperage rating.
⚫VOLTAGE
110 Volt –The GS-105(HS) requires a full 20-amp grounded circuit for 110-volt
operation.
⚫EXTENSION CORDS If used, should be as short as possible and not less than
12 gauge. Heavy duty cords are recommended.
⚫CIRCUITS that have less than 15 amps or that have other high demand
equipment or appliances (especially more than one heat seal machine) plugged
in, should not be used.
NOTE: If the supply cord is damaged, be sure to contact the manufacturer, its service
agent or a similar qualified person for a replacement to avoid hazard
CAUTION Failure to follow these instructions will cause:
1) Erratic controller functions. 2) Inaccurate displays and slow heat-up. 3) The circuit
breaker to disengage.
Ramspin system (Auto& Manual switch)
11.1 When the Ramspin system (Auto
& Manual switch) is facing down,
the machine will automatically open
after pressing is complete. (fig.11.1)
11.2 When the magnetic plate is facing
up, the machine needs to be
opened manually. (fig.11.2)
8
Turn on the System
3. Switch the System On
Adjusting the Temperature
4. ADJUST THE TEMPERATURE
4.1 Press “SET” button. “Set Temp”
lights located in the display will
illuminate. (figure 4.1)
4.2 Next, press the UP and DOWN
Arrow to increase or decrease the
figure to set the Temperature. The
temperature setting range is 170° F
(76° C) to 430° F (220° C).
9
Adjusting the Time
5. ADJUST THE TIME
Counter Setting
6. COUNTER SETTING (Used to show how many completed presses you have
done)
5.1 Once you have set your target
Temp., press the “SET” button
again. “Set Time”lights located in
the display will illuminate. (figure
5.1)
5.2 Next, press UP and DOWN Arrow
to increase or decrease the figure
to set the Time. The time setting
range is from 0 to 999S.
6.1 Once you have adjusted the time, press
“SET” button again. “Counter”lights
located in the display will illuminate
indicating. (figure 6.1)
6.2 You can press “SET”button to quit the
setting if you do not want to set the
Counter or you can press UP and
DOWN Arrow to adjust the counter if
needed. The counter setting range can
be set from 0~999.
10
Adjusting the Pressure
7.ADJUST THE PRESSURE
PRESSURE READOUT
REMEMBER: To allow for the thickness of your garment when adjusting the pressure.
Printing and Pressing
8.PRESS
NOTE: Please be aware after time is complete, gas shocks will automatically release
the platen into the “UP” position.
7.1 First, locate the LED Display on the
Press. The Pressure Adjustment Knob
is located in the center of the heat platen
(See figure 7.1)
7.2 To adjust the Pressure, simply turn the
Pressure Adjustment Knob to the right
or clockwise to increase the Pressure
and to the left or counterclockwise to
decrease the Pressure. The readout will
display the Pressure when locked down
in the print position.
7.3 A visual Pressure Readout is located on
the lower right side of the LCD Display.
When the handle is locked into the Print
Position, a pressure number will be
displayed. Readout will be on a scale of
0 - 9.A 0 Pressure readout would
indicate no pressure at all and 9 would
indicate very heavy pressure. (See
figure 7.3)
⚫Once your equipment has reached the designated temperature.
⚫Position the garment and application on the lower platen.
⚫Lower and lock the heat platen into the press position. Closing the press will
start the automatic timing process.
⚫The timer will automatically count down and lift the heat platen into the “UP”
position when the press cycle is complete.
7.1
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Andere Galaxy Elektrowerkzeuge Handbücher
