Gate NanoASR Bedienungsanleitung
Last update on DECEMBER 22, 2016 www.gatee.eu
USER GUIDE
GATE Menet, Wojtak Sp. J. does not take any responsibility for damages, injuries
and accidents resulting in the use of this product or the use of Air Electric Gun
with the product installed.
Information contained in this document is subject to updating without notice.
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE INSTALLING THE DEVICE
THE DEVICE COVER MUST NOT BE REMOVED BY THE USER
Caution must be exercised to prevent short circuiting the battery as the
consequences can be very dangerous.
We recommend that this product should be installed by an experienced airsoft
service.
Notice
Safety Summary
DANGER!
FOR YOUR SAFETY
USER GUIDE
02 WWW.GATEE.EU
CERTIFICATE OF CONFORMITY
The symbol shown here means that the product is classed as Electrical or Electronic Equipment
and should not be disposed with other household and commercial waste at the end of its
working life. The Waste of Electrical and Electronic Equipment (WEEE Directive 2012/19/U )
has been put in place to recycle products using best available recovery and recycling
techniques to minimize the impact on the environment. Purchasers shall take any old electrical
equipment to waste recycling public centers or points of sale.
E
PRODUCT DISPOSAL INSTRUCTIONS
GATE Menet, Wojtak Sp. J. hereby declares under our sole responsibility that the product
GATE NanoASR is in conformity with the essential requirements of the following Directives:
EC DIRECTIVE 2011/65/EU
This product has been certified as RoHS Compliant.
WARNING:
WARNING:
WARNING:
NOTE:
Before starting installation process, please ensure that your AEG is
empty and there are no BBs inside.
Always use a fuse between the battery and the mosfet.
Incorrectly connecting positive and negative battery terminals will
cause immediate damage to the unit and it can lead to fire.
Please check if you have downloaded the latest manual from the Technical Support
section of our website: www.gatee.eu. The Product Warranty Form is also
available there.
In case you have any difficulties while installing or using this product, we
recommend to email us at [email protected].
USER GUIDE
03
WWW.GATEE.EU
Table of Contents:
Safety Summary ........................................................................................................2
Table of Contents .......................................................................................................4
01. Overview ..............................................................................................................5
• Key Functions .........................................................................................................5
• Package Contents ...................................................................................................6
02. Installation ............................................................................................................7
• AEG standard installation diagram ........................................................................7
• Installation of NanoASR without replacement of wires.......................................7
• Installation of NanoASR with replacement of wires.............................................8
03. GATE Limited Warranty Policy ............................................................................9
04 WWW.GATEE.EU
USER GUIDE
01. Overview
NanoASR is the latest standard 3rd generation MOSFET. The application of the
most up-to-date transistors and microprocessor enabled us to create the smallest
and most reliable MOSFET in the market. Thanks to its special coating, it is resistant
to atmospheric conditions.
05
WWW.GATEE.EU
Key Functions
Do you want to achieve higher rate of fire and faster trigger response?
Are you planning power upgrade of your rifle? In that case, you need
a MOSFET.
It targets the energy from the battery directly to the motor, bypassing
the mechanical trigger contacts. As a result, you gain a higher rate
of fire of the rifle and faster trigger response, and the contacts
are protected against burn out.
MOSFET
USER GUIDE
We know how important reliability is on the battlefield. That’s why our
new MOSFET has thermal protection. In tandem with a time-lag fuse,
it fully protects your AEG installation.
Electronic Fuse
The usage of modern transistors and microcontroller has enabled us
to create the smallest and most reliable AEG Controller in the market.
3rd Generation MOSFET
This provides full compatibility with the micro-switches. It is fully
resistant to contact bounce. You gain a bigger ROF, a faster trigger
response and your MOSFET is less prone to heating.
Debouncing (Digital Interface)
06 WWW.GATEE.EU
Included in the kit:
NanoASR
Additional kit of Deans-T Connectors
Single signal wire for trigger contacts
Double signal wire for trigger contacts
01
02
03
04
02
04
03
USER GUIDE
01
07
WWW.GATEE.EU
02. Installation
To adapt the standard AEG installation to work with NanoASR you have to get to
the trigger contacts. In case of a GB v2 contacts are located inside a gearbox. With a
version 3 gearbox, installation is easier because the contacts are on the outside of
the gearbox. Please consult a local airsoft technician if you have never
disassembled a gearbox before or if you have any installation concerns.
Fig 1. Standard AEG wiring scheme
a) Installation of NanoASR without replacement of wires
Using this method, the original wiring is kept, and the connections are modified.
Referencing Figure 2, de-solder A wire from one of the trigger contacts and then
solder it to the B wire. It does not matter which wire you disconnect from the trigger
switches, just join two wires together at one terminal. In the place of the A wire,
solder additional single signal wire (03 – provided with the NanoASR kit). The
GATE wire is thin because it handles very low current and is only used for switch-
detection. If you have already connected the NanoASR between the battery and
the AEG, do not forget about a signal wire. Connect it to the top pin.
BATTERY
AEG Motor
A B
CONTACTS
C
up to 14.8V FUSE
USER GUIDE
08 WWW.GATEE.EU
Fig 2. Connection-modification scheme - the top view
b) Installation of with replacement of wires
Replacing the existing AEG wiring with a high-quality, low-resistance wiring in
conjunction with the installation of a MOSFET allows for the ultimate in efficiency.
16 awg or thicker wire is recommended. Solder the double signal wire (04 -
provided with the kit) to the contacts, according to the Figure 3.
NanoASR
Fig 3. Complete re-wiring scheme
USER GUIDE
03
TOP PIN
AEG Motor
CONTACTS
BATTERY
up to 14.8V FUSE
BATTERY
up to 14.8V FUSE 04
AEG Motor
CONTACTS
09
WWW.GATEE.EU
06. GATE Limited Warranty Policy
GATE Menet, Wojtak Sp. J. warrants that its Product is free from manufacturing and
material defects at the date of purchase and for a period of one (1) year from the date
of purchase and it is not-extendable. This Limited Warranty is conditioned upon
proper use of Product by Purchaser.
1. This Limited Warranty is valid provided that the owner provides a proof of
purchase and properly completed warranty form.
2. This Limited Warranty does not cover: (a) defects or damage (eg. mechanical,
thermal or chemical) resulting from accident, misuse (misinterpretation of the
instructions), abuse, neglect, unusual physical, electrical or electromechanical
stress, water immersion, repairs or structural modification of any part of Product
(eg. heat-shrink tube removal), or (b) the Product that has the serial number
removed or made illegible; (c) defects or damage from improper operation,
maintenance or installation, (d) installation of the products.
3. Requests for warranty are processed as soon as possible, not exceeding seven
(7) working days. The company's obligation under this Limited Warranty shall be
limited to providing replacement of part/s only.
Contact: [email protected]
USER GUIDE
Inhaltsverzeichnis
Andere Gate Halbleiter Handbücher
Beliebte Halbleiter Handbücher anderer Marken
Philips
Philips AN10369 Montage- und Bedienungsanleitung
GigaDevice Semiconductor
GigaDevice Semiconductor AN055 Montage- und Bedienungsanleitung
Hotenda
Hotenda MPC8349EA Gebrauchsanweisung
Fujitsu
Fujitsu F2MC-8FX Series Bedienungsanleitung
NXP Semiconductors
NXP Semiconductors AN10365 Montage- und Bedienungsanleitung
Fujitsu
Fujitsu F2MC-16L Series Bedienungsanleitung
BIRD
BIRD 8931A400-115 Bedienungsanleitung
Arrow
Arrow verical CYPRESS CY8CKIT-049-42 Series Handbuch
Texas Instruments
Texas Instruments SimpleLink CC2640 Bedienungsanleitung
Honeywell
Honeywell CD3000M-2PH Bedienungsanleitung
Southchip
Southchip SC8913 EVM Bedienungsanleitung
Toshiba
Toshiba TPC8402 Bedienungsanleitung
