Gator G395 Bedienungsanleitung
G395 Rear View Monitor +
Butterfly Reversing Camera
Instruction Manual
INTRODUCTION !
Thank you for purchasing the Gator G390 Rear View Monitor + Butterfly Reversing Camera.
This product is designed to provide you the driver with a rear view image whilst reversing your
vechicle. Please read the manual carefully before installation and operation.
INSTALLATION: !
The video signal is transferred from the camera to the monitor via an RCA cable that will need to
be run from the boot through the passenger compartment to the monitors wired loom run under the
dash. From there the power and video signals are sent directly to the monitor. At the rear of the car
the camera is powered directly from the reversing taillight.
F
F
F
F
M
M
M
Monitor
Camera
Moulded
splitter
Moulded
splitter
+
Powerwires
(ACC)
Power connector
(Positive wire only. Negative wire not required)
+
(Optional front camera)
(Camera priority)
INSTALLING THE CAMERA
In most instances, the camera is best mounted above the vehicles license plate as shown here.
!
!
!
!
INSTALLATION.!!
1. Connect the RED wire of the Cameras Power Harness to the wire that supplies power to
the reversing light globe (the wire that is energised only when the car is put into reverse).
Before making the electrical connection, temporarily disconnect the camera from the power
plug whilst making the connection to the back up light. Use a suitable splicing/crimp
connector (Scotch lock type) or strip connector. This connection can also be soldered,
making sure to insulate the joint with electrical insulation when done. The camera has only
one wire to connect (positive (+). There is no need to hook up a ground wire as the
camera gets its earth through the RCA lead. Hooking up the earth may cause a ground
loop. In this case Horizontal lines will appear in the image.
2. After you have insulated the join you can connect the power harness to the camera.
NOTE: Some cars that Run LED or Computer controlled lighting systems and may not
deliver enough voltage to run the camera. If the voltage at the reversing wire light is less
than +12 volts it may be necessary to use a relay to supply power to the transmitter
harness from the wiring in the front of the car. In this case the reversing light only needs to
trigger the relay. Make sure that you do not drill holes in the panels that have an opposite
face that is visible outside the car for example guard panels. In fact, whenever drilling holes
in the bodywork of a vehicle, always see what is on the other side.
3. Connect one end of the Supplied RCA Video lead to the RCA lead coming from the camera
then run the RCA lead to the front under side of the driver side dash board (This is were the
monitors loom will be located). To do this you will need to remove the rear seat to pass the
cable into the cabin area and you will need to remove the door scuff plates to run the wire
along the side of the vehicle. The RCA cable will be hidden when you replace the scuff
plates. When the cable is at the front of the vehicle the RCA cable needs to be run from the
scuff plate area to the under side of the dash behind the kick trim (Remove to run cable).
4. The monitor has two power wires to be connected. Connect the Red wire (Accessories
+12V) to a wire that is energised when the accessories position on the key is active (When
the radio is on) and the black wire to a ground wire or you can connect the back wire to the
body of the car using the steel of the cars body behind the kick trim as an earth. In this case
drill a small 1/8th hole and connect the wire using a suitable O-ring terminal. Scrape off the
cars paint around the hole to ensure a good earth.
5. Connect the RCA lead to the RCA Connector from the Monitors loom.
!
!
TESTING THE REVERSE CAMERA FUNCTION!
!
1. Engage the park brake and turn the ignition key to the on position. DO NOT start the
vehicle.
2. Select reverse gear with the gearshift. The Monitor will sense the Video signal from camera
automatically and image should start broadcasting the image of the rear of the vehicle.
SPECIFICATIONS
Monitor
· Size: 3.5 inch· Display Format: 480 x 234 RGB
· Video System: PAL / NTSC auto-switch
· Video Input x 2: Yellow = Reverse Camera Input
White = DVD Signal Input/optional camera
· Supply Power: DC12V +/-10%
Butterfly Camera
· Aluminum case & waterproof for outdoor use. IP67 Standard.
· Lense Angle 170 degree horizontal & 90 degree vertical
· Ultra bright night vision
TECHNICAL ASSISTANCE
If you need assistance setting up or using your Gator product now or in the future, call Gator
Support.
Australia
TEL: 03 –8587 8898
FAX: 03 –8587 8866
Mon-Fri 9am –5pm AEST
Please retain this user guide for future reference.
Inhaltsverzeichnis
