GBC Discovery 1100 Bedienungsanleitung
TS-82-914-90011
TS-82-914-90040
User Manual
PRODUCT CODE: DCV10001
• Welcome:
Thanks for purchasing this product. Please read the instructions carefully before using this
product.
• FCC Compliance Statement (Class A):
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received; including interference that may cause undesired operation.
• Federal Communications Commission (FCC) Statement :
This Equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
• European Community Compliance Statement (Class A):
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
The symbol of the crossed out wheeled bin indicates this product should
not be placed in municipal waste. Instead, you need to dispose of the waste
equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment.
1
Warning
1. Do not look directly at the LED light source, which may cause retinal damage.
2. Carry the product by holding the base of the main unit in both hands. Never hold the
product by the arm or the camera head only.
3. The camera can be damaged if it hits a desk surface or any hard object.
4. Never turn the arm in the opposite direction.
5. Be sure to keep one hand on the
device base when adjusting the arm
and camera head.
2
Preparing the Document Camera
Knowing the Document Camera Parts
Camera Head
LED Lamp
Gooseneck Arm
Microphone
Remote Control Signal Receiver
Control Panel
SD Card Slot
VGA Output Port
HDMI Output Port
USB Port
DC 5V Power Socket
Anititheft Slot
3
Control Panel
Icon Button Function
Power Power on/off
Menu/OK Show menu and select.
Up/Down Up/Down button
/PLB/BACK Enter playback mode to display
recorded still images and video
clips/Leave current menu
LAMP Turn on/off the LED lamp and
adjust the brightness of the LED
lamp
FLIP Flip image
OUTPUT OUTPUT VGA/HDMI output switch
SNAP/REC. Capture a still image/Record a
video clip
Zoom in Zoom in
Auto Focus One-time auto focus
Zoom out Zoom out
4
Remote Control
Button Function
Brightness hotkey
Power on / off
Freeze current image.
* Pause the clip while playing videos
Show or hide on-screen icons
To show or hide OSD menu
Playback mode to display recorded
pictures and video clips
Invert image 180°
Select and adjust
Record a video clip
Capture a still image
/ Zoom out / Zoom in
One-shot auto focus
/ Use the level bar to adjust the focus
manually
2X or 4X digital zoom
Highlight function on / off
Mask function on / off
Macro / Normal switch
Adjust highlighted / masked area
size
Set color for highlighted / masked
area
Button Function
VGA
HDMI
VGA-HDMI output switch
Picture in Picture function on /
off *For displaying a still image as
an insert while displaying another
image.
Infrared remote control can only be
used in proximity to the unit.
Remove the battery cover and load
the batteries into the battery com-
partment correctly according to the
“+” and “-” symbols.
Be sure to use two AAA batteries. Do
not use new and old batteries or dif-
ferent battery types together.
VGA
HDMI
5
Setting Up
This section provides useful tips on how to adjust the document camera smoothly for your
needs.
Illumination Lamp
If you are in a dark environment, please turn the
LED lamp on to make better exposure.
1. Press the LED lamp button ( ) on the base to
turn on/off the LED lamp.
2. Adjusting the brightness by pressing the lamp
button ( )
Output Switch
Adjust the Output Switch on the control
panel according to your output port.
Gooseneck Arm
The gooseneck arm can be adjusted to support various working areas.
6
If the document is not put in the
recommend working area, the image
should be rotated
by FLIP button ( ) on control
panel or remote control.
16.54”
11.69”
Height 16.93”
for Max. working
(16.54”x 11.69”)
Minimum height 7.09”
7
Adjusting the brightness
1. Press BRIGHTNESS button on the control panel ( ) or remote control ( ).
2. Use ( or ) buttons on the control panel or ( or ) buttons on the remote control to
increase or decrease the brightness level.
Zoom Function
Use the Zoom buttons ( / ) to zoom in or zoom out the screen.
Flip Function
Press the Flip Button ( ) to flip image
VGA
HDMI
VGA
HDMI
8
Adjusting the Focus
▶Automatic Focus
Press AF button ( ) to do an one-time auto focus. This function provides a one-time auto-
focus.
▶Manual Focus
Use the manual focus buttons ( / )( )
on remote control to finetune the focus.
Anti-glare
Anti-glare sheet is a transparent plastic that is overlaid on top of shiny object or glossy surface
to reduce the glare.
To use, simply place the anti-glare sheet on top of shiny object to glossy surface such as
magazine to reduce light reflectio
Functions indicated by can only be used by the remote control.
VGA
HDMI
+ Anti-glare
Inhaltsverzeichnis
Sprachen:
